• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.337-340
• /
• 2004

To develop the highly sensitive Magneto-Impedance sensor, the amorphous ribbon was micro-processed to meander type sensor pattern and the filter circuit was constructed with this pattern. Its external magnetic field dependence of impedance and the output properties of the filter circuit were investigated. The impedance of the pattern had a peak value at the magnetic field of 10 Oe and its changing ratio was about 280%. The impedance change per unit magnetic field was about 36%, in which the output with high sensitivity and linearity could be obtained. The output sensitivity was about 7%/Oe at bias field of 6 Oe..

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.88.5-88
• /
• 2002

A new floating power supply for the current measurement system of a high voltage power line is developed. It is confirmed that, the current measurement system can stably transfer the signal of the power line current about 50 - 300 A by using the proposed power supply. The excellent characteristics are obtained by the steady-state and transient experiments of the proposed circuit. $\textbullet$ The right figure shows the external view of the trial measurement system for 6.6 kV. In order to see the inside, 120 degrees of the insulator is cut. The toroidal coil for the power supply and the Rogowskii coil for the current sensor are both divided into two and fixed on the power line as...$\textbullet$ The proposed circuit can supply +5V and -5V voltages without using a solar cell and/or a battery.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.747-750
• /
• 2002

A circuit building block for realizing a continuous-time active-only current-mode integrator is presented. The proposed integrator is composed only of internally compensated type operational amplifier (OA) and operational transconductance amplifiers (OTAs). The integrator is suitable for integrated circuit implementation in either bipolar or CMOS technologies, since it does not require any external passive elements. Moreover, the integrator gain can be tuned through the transconductance gains of the OTAs. Some application examples in the realization of current-mode network functions using the proposed current-mode integrator as an active element are also given.

• Journal of Korean Society for Quality Management
• /
• v.25 no.1
• /
• pp.135-141
• /
• 1997

The Copper-Clad Laminate (CCL) is a main electronic component of specialtype printed circuit boards (PCBs) such as Silver Through Hole PCB. This CCL should have high reliability under the aging test, and usually the test is done at a higher temperature (110-$150^{\circ}C$) than the normal. Then, this test condition of high temperature may cause such quality problems as hole eccentricity and reduction of distance between part holes. After measuring the CCL shrinkage affected by temperature, the correction factor of a press mold was a, pp.ied to solve these problems. The results showed that the tolerance of hole pitch(${\pm}$$100{\mu}m$) was satisfactory and the internal and external failure costs were reduced by 55%.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1822-1824
• /
• 1996

Damage and upset of control and communication equipment due to transient overvoltages which occur due primarily to internal switching surge and external lightning surge are an important problems in electromagnetic compatibility(EMC). In this paper, we analyzed operation characteristic of metal oxide varistor widely used low voltage AC line using the electromagnetic transients program(EMTP) and compare it with experimental results and also, we modeled combination generator producing $1.2/50{\mu}s$ open circuit voltage and $8/20{\mu}s$ short circuit current as a source which is critical in calculating operation characteristic. Simulation results showed that most of Transient energy consumes at MOV located in service entrance side than load side, and it showed similar to experimental results. Therefore, entrance side MOV should be selected more energy capacity than that of load side MOV.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2254-2256
• /
• 2000

This paper presents an implantable telemetry LC resonance-type pressure sensor for the measurement of the ventricle pressure. This sensor consists of a capacitor and an inductor. This resonant circuit is magnetically coupled with an external antenna coil. The resonance frequency of the circuit decreases as the sensor capacitance is increased by the applied pressure. The inductance and the capacitance are 428nH and 0.98${\mu}F$, respectively. The resonance frequency is 245.7MHz when the differential pressure is zero. The sensitivity of the sensor is 9.477kHz/Pa.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.91-93
• /
• 1998

In this paper 30 kVA superconducting generator's transient-state electromagnetic analysis by FEM is described. The transient-state analysis by moving air gap technique was performed to analyze its 3 phase sudden short circuit characteristics. External circuit components were connected to generator model with end-winding resistance and inductance.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.3
• /
• pp.34-42
• /
• 1993

An analytic approach to wide-band amplification using simplified equivalent MESFET modeling has enabled an ultrabroad-band flat-gain amplifier from DC to microwave. The developed lossy-match ultrabroad-band amplifier operates as a RC coupled circuit in the low-frequency range and lossless impedance matching circuit in the microwave frequency range with gain compensation circuits. The reduced gain caused by external resistors is compensated using 2-stage cascade amplification, and the gain of designed unit is 12.5.+-.1dB from the vicinity of DC to 7GAz. The experimental gain characteristics are good agreement with computer simulated results. The input and output VSWRs are measured under 2:1 over the operating frequency range, and the gain goes down over 15dBrange with various gate bias voltages.

• Journal of the Korea Safety Management & Science
• /
• v.16 no.2
• /
• pp.111-119
• /
• 2014

This paper describes the design and implementation of a electromagnetic energy harvesting mechanism and electronic circuit for autonomous emergency call system. This analysis results show the power output of the proposed harvesting mechanism and circuit up to max power output 5V and it can hold up to 65 msec of the power generation and 10msec of the RF transmission. Based on the these testing results, the implementation of autonomous emergency call device without battery power or any external power source is feasible.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.8 s.227
• /
• pp.1159-1165
• /
• 2004

This paper describes fabrication of a micro cell counter integrated with an oxygen micropump and counting experiment with Sephadex G-25 beads ($70{\sim}100\;{\mu}m$). The pumping part consisted of a microheater, catalyst (manganese dioxide) enveloped with paraffin, hydrogen peroxide, and microchannel, and the counting part consisted of collimated light, a microwindow, and a phototransistor including an external circuit. The micropump generated oxygen gas by decomposing hydrogen peroxide with manganese dioxide, which was initiated by melting the paraffin with the microheater, and pumped beads in the microchannel. When the beads passed the microwindow, they shaded the collimated light and changed the illumination on the phototransistor, which caused the current variation in the circuit. The signals, according to the bead size, reached up to 22 mV with noise level of 2 mV during 50 seconds and the numbers of peaks were analyzed by magnitude.