• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.224-225
• /
• 2017

Ultra-high-strength concrete exposed to high temperature is likely to cause spalling. Spalling is caused by the vapor pressure of the concrete, and the vapor pressure may be different depending on the heating conditions of the concrete. Therefore, in this study, a ring-type restrained specimen was fabricated using ultra-high-strength concrete and the vapor pressure generated in the concrete by heating condition(rapid and slow heating) was evaluated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.745-750
• /
• 2014

The chatter vibration in the machining process plays bad role in machining quality such as high roughness as well as tool life and machine failure. And the grinding process under this risk in the fully automated factory is exposed to the unexpected mass machining quality problem. Studying the vibration signal of the hub bearing grinding process, the reason of chatter vibration was explained with the specific machining pattern of chatter. And this study suggests the chatter detecting method in the production line, which is monitoring the peak acceleration level around the natural frequencies of the specimen, and calculating kurtosis value by assuming the chatter is related to the resonance of the specimen. The suggested method was applied to the vehicle hub bearing grinding process and proved good to detecting the chatter induced machining quality problem.

• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.1003-1008
• /
• 1995

CVD-Si3N4/CVD-SiC/pack-SiC/pyro-carbon/(3-D C/C composite) multilayer coating was performed to improve the oxdiation resistance and erosion resistance properteis of the 3-D carbon/carbon composite, and the plasma test was performed to measure the oxidation resistance and erosion resistance properties. The thicknesses of each film layer were about 10${\mu}{\textrm}{m}$ for pack-SiC, 5${\mu}{\textrm}{m}$ for CVD-SiC and 40${\mu}{\textrm}{m}$ for CVD-Si3N4. When the multilayer coated specimen was exposed to the plasma flame with temperature of 500$0^{\circ}C$ for 20 seconds, it showed the weight loss five times less than that of the only pyro-carbon coated specimen.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.215-216
• /
• 2006

Solid insulation exposed to voltage is degraded by electrical tree process. And the degradation of the insulation is accelerated by voltage application. For this experimental, specimen of e1ectrical tree model is made by XLPE (cross-linked polyethylene). And the size of the specimen is $7*5*7\;mm^3$. Distance of need1e and plane is 2 mm. Voltages applied for acceleration test are 12 kV to 15 kV. And distribution characteristic of degraded stage is studied too. As a PD detecting and data process, discharge data acquire from PD detecting system (Biddle instrument). The system presents statistical distribution as phase resolved. Moreover the processing time of electrical tree is recorded to know the speed of degradation according to voltage.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1476-1477
• /
• 2006

Solid insulation exposed to voltage is degraded and by electrical tree process. And the degradation of the insulation is accelerated by voltage application. For this experimental, specimen of electrical tree model is made by XLPE(cross-linked polyethylene). And the size of the specimen is 7*5*7 $mm^3$. Distance of needle and plane is 2mm. Voltage applied for acceleration test are 12kV. And distribution characteristic of degraded stage is studied too. As a PD detecting and data process, discharge data acquire from PD detecting system(Biddle instrument). Their results of PD distribution show good present and are good discriminating skill.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1343-1344
• /
• 2007

In this paper, we investigated mechanical characteristics about thermal properties in semiconductor layer of power cables. Method of specimen making used solution mixing and Tensometer 2000 of Alpha used for measurement of stress and strain. Semiconductor layer made an experiment on separately environmental temperature$[25^{\circ}C]$ and high temperature$[90^{\circ}C]$ which running temperature$[90^{\circ}C]$ of cables exposed. As a result, specimen of applicable DFS(Dual Filler System) could know mechanical superiority that its structural characteristics reinforcement considered thermal characteristics.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1627-1629
• /
• 1999

In order to analysis the degradation process of epoxy/glass fiber for outdoor condition, FRP laminate was exposed to high temperature and water. Then the degradation process was evaluated by comparing contact angle, surface potential decay, and surface resistivity. For the change of wettability, the contact angle of thermal-treated specimen with the high temperature of $200^{\circ}C$ increased. But that of water-treated specimen decreased. The characteristic of surface potential decay shows the tendency of the remarkable decrease on water-treated specimens, but no difference on thermal-treated specimen compared with untreated one. Also, for the surface resistivity, it shows the same trend compared with the change of contact angle.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.51 no.3
• /
• pp.298-304
• /
• 2018

A single specimen of Gymnothorax pseudothyrsoideus (424.0 mm TL) belonging to the family Muraenidae, order Anguilliformes, was collected from Jeju Island, Korea, for the first time. The specimen is characterized by jaws closing completely, canine teeth on jaws, teeth not exposed when mouth is closed, ovoid posterior nostril, and body color ranging from yellowish brown to brownish with small dark spots aggregating to form larger spots that from approximately four irregular rows along the body. A comparison of mitochondrial DNA 16S rRNA sequences indicated that this specimen corresponds well with G. pseudothyrsoideus (K2P distance, d=0.002) but differs from other Gymnothorax species (11.9-13.7%). Therefore, the new Korean name "Geu-mul-nun-gom-chi" is proposed for the species G. pseudothyrsoideus.

• Restorative Dentistry and Endodontics
• /
• v.14 no.1
• /
• pp.199-204
• /
• 1989

The purpose of this study was to observe the anodic polarization curve from 4 kinds of low copper amalgam (Fine cut alloy, Spheralloy, Aristalloy and Amalcap) and 4 kinds of high copper amalgam (Dispersalloy, Sybraloy Orosphere and Tytin) obtained by using the potentiostat. The specimen made as the direction of manufacturer was stored at room temperature for about 7 days. The standard surface preparation was routinely carried out. The 0.9% saline solution was used as electrolyte in pH 6.8-7.0 at $37^{\circ}C$. The open circuit potential was determined after 30 minutes' immersion of specimen. The scan rate was 1mV/sec and the surface area of amalgam exposed to the solution was 0.785$cm^2$ for each specimen. All potentials reported are with respect to Ag/AgCl eelctrode. The following results were obtained. 1. The corrosion potential of high copper amalgams was higher than one of low copper amalgams, and the current density of high copper amalgam was lower than one of low copper amalgams. 2. The low copper amalgams had the similar pattern of polarization curve, but the high copper amalgams had the different pattern one another. 3. The polarization curve of Orosphere amalgam which is the admixed type was similar to one of low copper amalgam.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.2 s.257
• /
• pp.253-259
• /
• 2007

A new material tester has been developed to measure mechanical properties of thin film specimens at high temperature. It is useful for observing oxide film growth or local deformation on the surface, and for measuring creep strength. Main characteristics of the tester is as follows; First, high temperature is achieved by Joule heating generated by electricity passing through the specimen, which does not need to enclose the specimen by a furnace or a heating chamber. The exposed specimen enables one to observe the surface during the test. Because the overall size of the test rig is compact, the whole test rig can be placed in a chamber for environmental controlled tests. The loading device is from a level scales. Not only static load with fixed counter weight, but also variable load by moving counter weight controlled remotely can be applied for an ordinary creep test and creep-fatigue test, respectively. The detail of the construction, operation principle, and the specification are described. And also, an example of test result obtained using the creep tester is presented.