• 한국기계가공학회지
• /
• 제13권4호
• /
• pp.13-20
• /
• 2014

In this paper, the effects of a nonionic surfactant on the etch uniformity and the etch profile during the wet-etching process of high-purity aluminum were investigated for the fabrication of uniform micropattern arrays. To improve the surface roughness of a high-purity aluminum plate, a mechanical lapping process and an electrolytic polishing process were used. After electrolytic polishing process, the surface roughness, Ra, of the high-purity aluminum plate was improved from $1.25{\mu}m$ to $0.02{\mu}m$. A photoresist was used as an etching mask during the aluminum etching process, where the mixture of phosphoric acid, acetic acid, nitric acid, a nonionic surfactant and water was used as the aluminum etchant. Different amounts of the Triton X-100 nonionic surfactant were added to the aluminum etchant to investigate the effect of a nonionic surfactant during the wet-etching process of high-purity aluminum. The etch rate and the etch profile were measured by an optical interferometer and a scanning electron microscope.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1269-1271
• /
• 2008

We find some array mura are caused by S/D bridge or channel open in 4 mask process. The gray tone PR thickness non-uniformity is the main reason of these defects. By the adjustment of exposure and dry etch parameters, S/D bridge and channel open ratio drops by 10.87%.

• 전자공학회논문지A
• /
• 제32A권12호
• /
• pp.115-121
• /
• 1995

A mask for x-ray lithography is fabricated with SiN membrane and WTi absorber. SiN membrane is deposited by plasma enhanced chemical vapor deposition, and the stress of SiN membrane is controlled to be less than 100 MPa by rapid thermal annealing. WTi absorber is reactively deposited by DC-magnetron type sputter, and the working gases are argon and nitrogen. Added nitrogen is contributed to the stress of WTi absorber. The stress of WTi absorber is controlled to be less than $\pm$ 100 MPa by controlling the deposition pressure. 10$\mu$m WTi pattern is delineated on SiN membrane by dry etching technique.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1364-1369
• /
• 2004

New method for the design, fabrication, and calibration of micro-machined heat flux sensor has been developed. Two types of micro-machined heat flux sensor having different thicknesses of the thermal-resistance layer are fabricated using the MEMS technique. Photo-resist patterning using a chrome mask, bulk-etching and copper-nickel sputtering using a shadow mask are applied to make heat flux sensors, which are calibrated in the convection-type heat flux calibration facility. The sensitivity of the device varies with thermal-resistance layer, and hence can be used to measure the heat flux in heat-transfer phenomena.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.12.1-12.1
• /
• 2009

For the micro conductive line, memory device fabrication process use many expensive processes such as manufactur-ing of photo mask, coating of photo resist, exposure, development, and etching. However, direct printing technology has the merits about simple and cost effective processes because nano-metal particles contained inks are directly injective without mask. And also, this technology has the advantage about fabrication of fine pattern line on various substrates such as FPCB, PCB, glass, polymer and so on. In this work, we have fabricated the fine and thick metal pattern line on flexible PCB substrate for the next generation electronic circuit using Ag nano-particles contained ink. To improve the line tolerance on flexible PCB, metal lines are fabricated by sequential prinitng method. Sequential printing method has vari-ous merits about fine, thick and high resolution pattern lines without bulge.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 A
• /
• pp.518-520
• /
• 2004

In these days, there is a demand to develop fault current limiters(FCLs) to reduce excessive fault current and protect electrical equipments which are installed in the transmission and distribution power systems. We considered the resistive superconducting FCLs among the various kinds of FCLs. In this study, in order to develop the resistive superconducting FCL of 6.6kV 200A $3\phi$, we designed the new mask pattern for etching YBCO films by means of numerical analysis method, current limiting experiments and visualization of bubbles in films and investigated dielectric performance of the designed mask by using elecrtostatic numerical analysis method and breakdown experiments. We etched YBCO films by using the newly designed mask, connected the etched films in series and in parallel, and designed the 6.6kV resistive SFCL and then we observed the current limiting characteristics of the SFCL.

• 한국세라믹학회지
• /
• 제36권1호
• /
• pp.55-60
• /
• 1999

Hexamethyldisilane(Si2(CH3)6)의 single precursor를 출발원료로 사용하여 화학기상증착법으로 Si 기판위에 buffer층의 형성 없이 $\beta$-SiC의 박막을 증착하였다. Si 기판과 SiO2 mask에서 SiC 박막 증착의 선택성을 위하여 HCI의 식각 가스를 도입하였고 출발원료와 HCI 가스의 공급방법을 변화시켰다. SiC 박막 증착 과정에서 HCI 가스의 도입이 막의 표면 조도에 미치는 영향을 조사하였고 Hall 측정을 통하여 SiC 막의 전기적 특성을 조사하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.770-772
• /
• 1998

The highest etch rate of Pt film was obtained at 10% $Cl_2$/90% Ar gas mixing ratio in our previous investigation. However, the problems such as the etch residues(fence) remained on the pattern sidewall, low selectivity to oxide as mask and low etch slope were presented. In this paper, the etching by additive $O_2$ gas to 10% $Cl_2$/90% Ar gas base was examined. As a result, the fence-free pattern and high etch slope was observed and the selectivity to oxide increased without decreasing of the etch rate. And the reasons for this phenomenon was investigated by XPS(x-ray photoelectron spectroscopy) surface analysis and plasma characteristic.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1509-1511
• /
• 2001

In this study, etching characteristics of polyimide(Pl) film with $O_2/CF_4$ gas mixing ratio was studied using inductively coupled plasma (ICP). The etch rate and selectivity were evaluated to chamber pressure and gas mixing ratio. High etch rate (over 8000$\AA$/min) and vertical profile were acquired in $CF_4$/($CF_4+O_2$) of 0.2. The selectivities of polyimide to PR and polyimide to $SiO_2$ were 1.15, 5.85, respectively. The profiles of polyimide film etched in $CF_4/O_2$ were measured by a scanning electron microscope (SEM) with using an aluminum hard mask pattern. The chemical states on the polyimide film surface were measured by x-ray photoelectron spectroscopy (XPS).

• 대한기계학회논문집A
• /
• 제20권10호
• /
• pp.3113-3125
• /
• 1996

The objective of this study is to develop novel method named mechanical and chemical machining technique, which is capable of producing three dimensional patterns of few micrometers in dimension on a silicon wafer without the use of a mask. The strategy is to impart mechanical energy along the path of the pattern to be fabricated on a single crystal silicon by way on introdusing frictional interaction under controlled conditions. Then, the surface is preferentially etched to reveal the areas that have been mechanically energized. Upon completion of the etching process, the three dimensional pattern is produced on the silicon surface. Experiments have been conducted to identify the optimal tool material, geometery, as well as fabrication condition. The new technique introduced in this paper is significantly simpler than the conventional method which require sophisticated equipment and much time.