• 한국통신학회논문지
• /
• 제28권10B호
• /
• pp.899-915
• /
• 2003

다양한 미디어 콘텐츠를 최선형 서비스에 머무르고 있는 유무선 인터넷의 네트워크 상태에 무관하게 전달하기 위해서는 네트워크 가장자리에서 동작하는 미디어 응용프로그램들이 보다 적응화되어야 한다. 즉 응용프로그램에서 전달하고자 하는 미디어 콘텐츠가 요구하는 네트워크 품질에 대한 요구와 기반 네트워크 서비스론 적응적으로 연결하는 것이 매우 중요하다. 본 논문에서는 먼저 응용프로그램에게 요구되는 혼잡제어 및 전송율 제어, 오류 제어, 그리고 동기화 및 적응형 재생 등과 같은 네트워크 적응화 기능들에 대해 의논한다. 이어서 네트워크 적응적 미디어 스트리밍을 실현하는 기반이 되는 요소들을 물리적인 네트워크, 프로토콜 지원에서 미들웨어에 걸치는 총체적인 지원의 구도하에서 설명한다. 최종적으로는 상기한 미디어 응용프로그램과 네트워크 지원 기반을 동시에 이해하면서 실현되는 동적인 네트워크 적응화의 구조를 제안한다.

• Nuclear Engineering and Technology
• /
• 제31권5호
• /
• pp.486-497
• /
• 1999

The local heat transfer coefficient is experimentally investigated for the reflux condensation in a countercurrent flow between the steam-air mixture and the condensate, A single vertical tube has a geometry which is a length of 2.4m, inner diameter of 16.56mm and outer diameter of 19.05mm and is made of stainless steel. Air is used as a noncondensible gas. The secondary side has a shape of annulus around vertical tube and the lost heat by primary condensation is transferred to the coolant water. The local temperatures are measured at 11 locations in the vertical direction and each location has 3 measurement points in the radial direction, which are installed at the tube center, at the outer wall and at the coolant side. In three different pressures, the 27 sets of data are obtained in the range of inlet steam flow rate 1.348∼3.282kg/hr, of inlet air mass fraction 11.8∼55.0%. The investigation of the flooding is preceded to find the upper limit of the reflux condensation. Onset of flooding is lower than that of Wallis' correlation. The local heat transfer coefficient increases as the increase of inlet steam flow rate and decreases as the increase of inlet air mass fraction. As an increase of the system pressure, the active condensing region is contracted and the heat transfer capability in this region is magnified. The empirical correlation is developed by 165 data of the local heat transfer. As a result, the Jacob number and film Reynolds number are dominant parameters to govern the local heat transfer coefficient. The rms error is 17.7% between the results by the experiment and by the correlation.

• 한국안광학회지
• /
• 제13권4호
• /
• pp.103-107
• /
• 2008

목적: 본 연구는 처음 근용 안경을 착용하고자 하는 노안을 대상으로 근용 가입도 검사를 하여 가입도와 나이, 성별, 직업군, 구면 도수, 난시 도수와의 상관관계를 평가하고자 하였다. 방법: 155명의 피검사자의 좌, 우안(310안)을 대상으로 비조절마비 자각적 굴절 검사 및 크로스 실린더를 이용한 근용 가입도 검사를 하였다. 결과: 최초 근용 가입도는 +0.75D에서 +1.75D까지 검사되었고, 43세 이전의 평균 가입도는 +1.06D, 44세~46세까지는 +1.08D, 47세~49세까지는 +1.23D, 50세 이상에서는 +1.46D이었다. 피검사자의 평균 연령은 47.6세, 남자 74명, 여자 81명이었고 근거리 직업군이 71명, 원거리 직업군이 83명이었다. 결론: 가입도는 나이, 직업군, 난시 도수와 높은 상관성을 나타내었다(p<0.05, p<0.05, p<0.05).

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권1호
• /
• pp.65-74
• /
• 2004

The heat transfer coefficient and pressure drop of $CO_2$(R-744) during gas cooling Process of carbon dioxide in a horizontal tube were investigated experimentally and theoretically. The experiments were conducted without oil in the refrigerant loop. The main components of the refrigerant loop consist of a receiver. a variable-speed pump. a mass flowmeter, an evaporator. and a gas cooler(test section). The main components of the water loop consist of a variable-speed Pump. an constant temperature bath. and a flowmeter. The gas cooler is a counterflow heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus The test section consists of smooth, horizontal stainless steel tube of 9.53 mm outer diameter and 7.75 mm inner diameter. The length of test section is 6 m. The refrigerant mass fluxes were 200 ~ 300 kg/($m^2{\cdot}s$) and the inlet pressure of the gas cooler varied from 7.5 MPa to 8.5 MPa. The main results were summarized as follows : The predicted correlation can evaluated the R-744 exit temperature from the gas cooler within ${\pm}10%$ for most of the experimental data, given only the inlet conditions. The predicted gas cooley capacity using log mean temperature difference showed relatively food agreement with gas cooler capacity within ${\pm}5%$. The pressure drop predicted by Blasius estimated the pressure drop on the $CO_2$ side within ${\pm}4.3%$. The predicted heat transfer coefficients using Gnielinski's correlation evaluated the heat transfer coefficients on the $CO_2$ side well within the range of experimental error. The predicted heat transfer coefficients using Gao and Honda's correlation estimated the heat transfer coefficients on the coolant side well within ${\pm}10\;%$. Therefore. The predicted equation's usefulness is demonstrated by analyzing data obtained in experiments.

• 대한물리의학회지
• /
• 제9권2호
• /
• pp.201-211
• /
• 2014

PURPOSE: The purpose of this study was to investigate the inter-rater absolute reliability and the concurrent validity of the Tinetti-gait scale that was translated into Korean for chronic stroke patients. METHODS: Fifty-two patients with post-stroke participated in this study. Inter-rater reliability was analyzed by Intraclass Correlation Coefficient ($ICC_{3,1}$) and Kappa coefficient, and absolute reliability was analyzed by the Standard Error of Measurement (SEM), and the Minimal Detectable Change (MDC). Concurrent validity was analyzed by correlating between the Tinetti-gait scale and physical functions. The physical functions were measured by using the Dynamic Gait Index(DGI), 10m walking test(10WT), One Leg Standing Test of affected/non-affected side(OLST), Sit to Stand test(STS), (Fugl Meyer assessment of Lower Extremity(FM-LE). RESULTS: The inter-rater reliability of the Tinetti-gait scale was high; $ICC_{(3,1)}=.91$ (95% CI=.85~.95) (very reliable), the range of Kappa coefficient were .73~.92 (substantial~good). The inter-rater agreement of the each item in Tinetti-gait scale ranged from .74 to .92 (95 % CI=.59~.95) (reliable~very reliable). The SEM and MDC were .56 and 1.55, respectively. In the results of concurrent validity, there were moderate positive correlation between Tinetti-gait scale and DGI (r=.78), 10WT (r=.74), OLST (r=.65~.73), FM-LE (r=67). And there was moderate negative correlation between Tinetti-gait scale and STS (r=-79) (p<.01). CONCLUSION: The Tinetti-gait scale(Korean version) was a reliable and valid tool to measure gait ability in patients with chronic stroke. Thus, it could be a useful tool for examining a gait ability of post-stroke patients. Further study should be conducted to investigate the usability to predict fall risk of post-stroke patients of the Tinetti-gait scale.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.503-506
• /
• 2005

The PWR Nuclear Fuel assembly consists of more than 250 fuel rods that are supported by leaf springs in the cells of more than 10 Spacer Grids (SG) along the rod length. Since it is not easy to conduct mechanical tests on a full-scale model basis, the small-scaled rod bundle (5$\times$5) is generally used for various performance tests during the development stage. As one of the small-scaled tests, a flow test should be carried out in order to verify the performance of the spacer grid like the coolant mixing performance and to obtain the Flow-Induced Vibration (FIV) characteristics of the rod bundle over the specified flow range. A vibration test should be also performed to obtain the modal parameters of the bundle prior to the flow test. In this study, we want to develop the estimation procedure of the damping ratio for the small scaled test bundle. For the damping factor of the rod bundle and the grid case at the first vibration mode, as one of the vibration tests, a so-called pluck testing has been performed in air as a preliminary test prior to in-flow damping measurement test. Logarithmic decrement method is used for calculation of the damping ratio. Estimated damping ratio of the rod bundle is about 0.7% with reasonable error of 2% for the previous results. Nonlinear behavior of the rod bundle might be stem mainly Iron the rod-grid support configuration.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.551-554
• /
• 2005

The method of the reduction of the automotive induction noise can be classified by the method of passive control and the method of active control. However, the passive control method has a demerit to reduce the effect of noise reduction at low frequency (below 500Hz) range and to be limited by a space of the engine room. Whereas, the active control method can overcome the demerit of passive control method. The algorithm of active control is mostly used the LMS (Least-Mean-Square) algorithm because the LMS algorithm can easily obtain the complex transfer function in real-time. Especially, When the Filtered-X LMS (FXLMS) algorithm is applied to an ANC system. However, the convergence performance of LMS algorithm goes bad when the FXLMS algorithm is applied to an active control of the induction noise under rapidly accelerated driving conditions. Thus Normalized FXLMS algorithm was developed to improve the control performance under the rapid acceleration. The advantage of Normalized FXLMS algorithm is that the step size is no longer constant. Instead, it varies with time. But there is one additional practical difficulty that can arise when a nonstationary input is used. If the input is zero for consecutive samples, then the step size becomes unbounded. So, in order to solve this problem. the Correlation FXLMS algorithm was developed. The Correlation FXLMS algorithm is realized by using an estimate of the cross correlation between the adaptation error and the filtered input signal to control the step size. In this paper, the performance of the Correlation FXLMS Is presented in comparison with that of the other FXLMS algorithms based on computer simulations.

• 한국측량학회지
• /
• 제28권5호
• /
• pp.485-491
• /
• 2010

붕괴된 사면의 정보는 제2차 피해의 발생우려가 있기 때문에 신속 정확하게 지형자료를 획득할 수 있어야 하고, 필요에 따라서 접근하지 않고 간접적인 측량방식으로 보다 효율적으로 표현할 수도 있어야 한다. 따라서 본 연구에서는 무인 헬리콥터 사진촬영시스템을 이용하여 붕괴된 도로 절개지 사면에 근접하여 상공에서 정지비행으로 대상지역의 영상을 촬영하였다. 그리고, 무타켓 Total Station에 의해 관측된 점과 영상해석에 의해 분석된 좌표점 10개와 비교한 결과 절대치 평균값은 X축 방향으로 평균 0.056m, Y축 방향으로 0.082m, Z축 방향으로 0.066m으로 나타났다. 또한, 검사점 10점에 대한 오차의 RMSE는 X축 방향으로 0.015636m, Y축 방향으로 0.021319m, Z축 방향으로 0.018734m로 나타났다. 따라서, 이러한 절개지 붕괴사면의 지형에 대하여 관계형 영상정합방법에 의해 접근하지 못하는 위험지역에서의 사면 범위와 각사면의 종 횡단면을 나타낼 수가 있었다.

• 한국산학기술학회논문지
• /
• 제13권8호
• /
• pp.3301-3306
• /
• 2012

LED 칩 패키징에서 다이 본딩은 분할된 칩을 리드 프레임에 고정시켜 칩이 이후 공정을 견딜 수 있도록 충분한 강도를 제공하는 중요한 공정이다. 기존의 다이 본더의 픽업 장치는 단순히 콜렛의 하강 동작과 이젝터 핀의 상승 동작만으로 구동되어 픽업 장치와 다이가 접촉하는 순간 충격에 의한 다이의 손상과 위치 정렬 오차에 대한 문제점이 발생한다. 본 연구에서는 위치 정렬 에러 및 다이의 손상을 최소화시키기 위하여 고정밀, 고속 이송이 가능한 픽업 헤드를 사용한 다이 본더 시스템을 개발하였다. 구조적 안정성을 평가하기 위해 다이 본더의 유한요소모델을 생성하였고 구조 해석을 수행하였다. 그다음, 다이 본더의 작동 주파수에 대해 픽업 헤드의 유한요소모델을 이용하여 진동해석을 수행하였다. 해석 결과, 다이 본더에 작용하는 응력 및 변위, 고유진동수에 대해 분석하였고 개발된 시스템의 구조적 안정성에 대해 확인하였다.

• Journal of Korean Neurosurgical Society
• /
• 제39권4호
• /
• pp.256-259
• /
• 2006

Objective : Having a reliable and reproducible measurement technique to measure the sagittal contour in vertebral fractures is paramount to clinical decision making. This study is designed to determine the most reliable measurement technique in osteoporotic vertebral compression fracture. Methods : Fifteen lateral radiographs of thoracic and lumbar fractures were selected and measured on two separate occasions by three spine surgeons using six different measurement techniques [Centroid, Harrison Posterior Tangent Methods and 4 different types of modified Cobb method]. The radiograph quality was assessed and the center beam location was determined. Statistical analysis including ANOVA for repeated measures was carried out using the SAS software [v 8.0]. Results : The inter and intraobserver variance of the Cobb method 4 and Harrison posterior tangent method were significantly lower than the other four methods. The intraobserver correlation coefficients were the most consistent using the Cobb method 4 [0.982]. which was followed by the Harrison posterior tangent [0.953] and Cobb methods 1 [0.874]. The intraobserver agreement [% of repeated measures within 5 degrees of the original measurement] ranged from 42% to 98% for each technique for all three observers, with the Cobb method 4 showing the best agreement [97.8%] followed by the Harrison posterior tangent method [937%]. Conclusion : The Cobb method-4 and Harrison posterior tangent methods, when applied to measuring the kyphosis, are reliable and have a similar small error range. The Cobb method 4 shows the best overall reliability. However, the centroid method and Cobb method using a fractured endplate do not produce an accurate result due to inter and intraobserver differences in determining the baseline.