• 전자공학회논문지A
• /
• 제33A권7호
• /
• pp.156-161
• /
• 1996

Accurate equivalent circuit modeling using multi-circuit optimization has been perfomred for detemining small-signal model of AlGaAs/GaAs HBTs. Three equivalent circuits for a cutoff biasing and two active biasing at different curretns are optimized simultaneously to fit gheir S parameters under the physics-based constrain that current-dependent elements for one of active circuits are connected to those for another circit multiplied by the ratio of two currents. The cutoff mode circuit and the physical constrain give the advantage of extracting physically acceptable parameters, because the number of unknown variables. After this optimization, three ses of optimized model S-parameters agree well with their measured S-parameters from 0.045 GHz to 26.5GHz.

• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2004년도 하계학술대회
• /
• pp.295-297
• /
• 2004

A double-role double through switch with defected ground structure (DGS) is Proposed. The equivalent circuit for the proposed switch structure is derived based on equivalent circuit of newly proposed DGS unit structure. The equivalent circuit parameters of DGS unit are extracted by using the circuit analysis method The on/off operation of the proposed switch Is obtained by varying the capacitance in the ground metallic plane The experimental results show excellent insertion loss characteristic at on state and isolation characteristic at off state.

• 전자공학회논문지A
• /
• 제33A권6호
• /
• pp.164-171
• /
• 1996

We report the experimental resutls on AlGaAs/GaAs heterojunction bipolar transistors (HBTs) with carbon-doped base structure. To characterize the output power, load-pull mehtod was employed. By characterizing the devices with HP8510C, we extracted the small-signal equivalent circuit. The HBTs were fabricated employing wet mesa etching and lift-off process of ohmic metals. the implementation of polyimide into the fabriction process was accomplished to obtain the lower dielectric constant resultig in significant reduction of interconnect routing capacitance. The fabricated HBTs with an emitter area of 6${\times}14{\mu}m^{2}$ exhibited current gain of 45, BV$_{CEO}$ of 10V, cut-off frequency of 30GHz and power gain of 1 3dBm. To extract the small signal equivalent circuit, the de-embedded method was applied for parasitic parameters and the calculation of circuit equations for intrinsic parameters.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.97-99
• /
• 2002

3D Equivalent magnetic Circuit Network Method (EMCNM) is comparatively the easy way that analyzes 3D models of Electric Machine by using permeance as a distributive magnetic circuit parameter under the existing magnetic equivalent circuit method and Numerical Method. The existing 3D EMCNM could not correctly describe the shape of an analysis target when using rectangular shape element or fan shape element, so it made errors when calculating permeance. Therefore, this paper use the trapezoidal element contained rectangular element. This paper calculate the torque based on the maxwell stress tenser method when the airgap is one layer, three layers, and 5 layers, respectively.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1999년도 춘계학술대회 논문집
• /
• pp.328-335
• /
• 1999

Three phase full bridge rectifier has been used to obtain dc voltage from three phase ac voltage source. The rectifier system has drawbacks that power factor is low and power flow is unidirectional. Therefore, when dc voltage increases due to regeneration of power the dynamic resister for dissipation of regeneration power must be installed. But three phase PWM converter can be controlled to operate with unity power factor and bidirectional power flow. Therefore when the PWM converter is used as do supply system, the dissipating resistor is not necessary. On this thesis, in order to design a controller having good performance, the hee phase PWM converter is completely modeled by using circuit DQ-transformation and thus a general and simple instructive equivalent circuit is obtained; the inductor set becomes a second order gyrator-coupled system and three phase inverter becomes a transformer as well. Under given phase angle(${\alpha}$) and modulation index(MI) of the three phase inverter, the dc and ac characteristics are obtained by analysis of the transformed equivalent circuit The validity of the equivalent circuit is confirmed through PSPICE simulation. And based on the dc and ac characteristics a controller with unity power factor is proposed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.120-122
• /
• 2005

Magnetic field analysis of claw-pole type generator using equivalent circuit is presented in this paper. On the basis of 3D geometry and flux paths, equivalent magnetic circuit is designed and field analysis is performed by solving the circuit. Non-linear characteristic of material is considered for precise analysis results. 3D FEA is performed to verify analysis results, and flux densities in rotor and stator regions are compared. Calculated no-load back emf for field input voltage and speed are verified by experiment. Comparing to 3D FEA, presented method provides precise results with instant calculation time.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권3호
• /
• pp.132-138
• /
• 2005

In this paper a DPDT(Double-Pole Double Through) switch with defected ground structure(DGS) is proposed. The equivalent circuit for the proposed switch structure is derived according to based on equivalent circuit of proposed DGS unit structure. The equivalent circuit parameters of DGS unit are extracted by using the circuit analysis method. The on/off operation of the proposed switch is obtained by varying the capacitance of the varactor diode at the defected ground plane. In the case of ON state, the insertion loss of the fabricated DPDT was shown under 1dB. And in OFF state, we found the rejection characteristic over 20dB at the designed frequency 2.45GHz. The experimental results show excellent insertion loss at on state and isolation at off state.

• Journal of electromagnetic engineering and science
• /
• 제15권1호
• /
• pp.26-30
• /
• 2015

In this paper, a simple equivalent circuit model for a defected ground structure (DGS) microstrip line with stepped impedance slot-lines in the ground plane is presented. In addition, an analytic expression for the resonance frequency of the proposed structure is derived. In equivalent circuit modeling, the capacitance and the inductance of the resonance circuit are evaluated from the dimensions of the etched pattern in the ground plane. The resonance frequencies calculated from the proposed method are compared with those obtained with an electromagnetic (EM) simulation.

• 한국전기전자재료학회논문지
• /
• 제26권7호
• /
• pp.515-521
• /
• 2013

Magnetoelectric(ME) bulk composites with PZT-PNN-PZN/$Fe_2O_4$ were prepared by using a conventional ceramic methods and investigated on the ME voltage vs frequency of ac magnetic fields. We made the electric equivalent circuits by using the Maxwell-Wagner model and simulated the frequency dependence of ME voltage in low frequency region. ME devices were described by a series of two equivalent circuits of piezoelectric and magnetic, which have the relaxation time ${\tau}$ due to the interaction between ME device and load resistor. Equivalent circuit of piezoelectric material is independent of frequency. However ferrite magnetic materials have Debye absorption and dipolar dispersion, whose equivalent circuit is a function of frequency. Therefore we suggest the resistance in the equivalent circuit is proportion to $1+{\omega}^2{\tau}^2$ and the capacitance is in inverse proportion to $1+{\omega}^2{\tau}^2$ in the magnetic materials.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.613-619
• /
• 2000

This paper presents a mettled to reduce the number of conductors of catenary system for estimating line constants. Conductors of a catenary system are grouped and reduced. For example, the model representing the contact and the messenger conductors with a single equivalent conductor is. probably more realistic than assuming the two conductors completely separated, since they are generally connected by droppers every few meters. Therefore, this paper shows the method to reduce the number of conductors using electric circuit theory. To verify the results, we compared the equivalent line constants obtained by proposed method with those obtained by measurement.