• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.7
• /
• pp.395-400
• /
• 2004

In this paper, the four-pole elliptic function microstrip filter at 2.4GHz band with fractional bandwidth of 4% is realized using compact miniaturized hairpin resonators. The parallel algorithm FDTD method is used to analyze S-parameter of hairpin resonator filter more accurately, and to calculate the electric coupling and magnetic coupling among the hairpin resonators. Absorbing boundary conditions for mesh termination used Sulivan's simplified PML and the FDTD code was paralleled by MPI for IBM SP2 which had enhanced calculation speed. The experimental measurements are performed by HP8720D vector network analyzer. Measured results on fabricated hairpin type cross coupled bandpass filters show good agreements with theoretic results.

• Journal of Advanced Navigation Technology
• /
• v.5 no.2
• /
• pp.141-148
• /
• 2001

This paper describe the development of narrow-band passband filter with small package and low loss, high selectivity performance. This filter is placed between power amplifier and frequency mixer of IMT-2000 mobile equipment. The elliptic-function narrow-band passband filter is designed with new architecture using the microstrip line. This package is very small by $3.2cm{\times}1.25cm$ and have the 3 % 3 dB bandwidth. Also in the passband the insertion loss is about 2.5 dB and is better than older RF SAW filter(insertion loss: 3.2 dB). In the stop-band it has the two deep notch under the -56 dB.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.1
• /
• pp.49-58
• /
• 1999

This paper describes an integrated low pass filter fabricated by using $0.8{\mu}m$ single poly CMOS ASIC technology. The filter has been designed for a 5th-order elliptic switched capacitor filter with cutoff frequency of 5khz, 0.1dB passband ripple. The filter consists of MOS swiches poly capacitors and five CMOS op-amps. For the realization of the SC filter, continuous time transfer function H(s) is obtained from LC passive type, and transfered as discrete time transfer H(z) through bilinear-z transform. Another filter has been designed by capacitor scaling for reduced chip area, considering dynamic range of the op-amp. The test results of two fabricated filters are cutoff frequency of 4.96~4.98khz, 35~38dB gain attenuation and 0.72~0.81dB passband ripple with the ${\pm}2.5V$power supply clock of 50KHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.352-361
• /
• 2010

In this paper, a compact 20 W block-up-converter for C-band satellite communication is designed and implemented. The designed block up-converter consists of an intermediate frequency circuit, a mixer and local oscillator, a driver amplifier, a solid-state power amplifier, waveguide circuits, and a power supply module. To reduce the size of the block-up-converter, all circuits are assembled within an housing, so its dimension is just $21{\times}14{\times}11cm^3$. Especially, the waveguide filter and microstirp-to-waveguide transition are easily implemented using an housing. Also, to meet spurious and harmonics specification, various compact microstrip filters including an elliptic filter are integrated. Measurement results show that the developed block up-converter has good electrical performances: the output power of 43.7 dBm, the minimum gain of 65 dB, the gain flatness of ${\pm}1.84$, the IMD3 of -35 dBc, and the harmonic level of -105 dBc.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.10
• /
• pp.820-825
• /
• 2010

In this study, we intended to design the optimal Fermi filter to apply the k-space date that is knee image of the rheumatoid arthritis patient acquired from the MRI (magnetic resonance imaging) instrument. After deciding the suitable coefficient for the Fermi filter, the results were compared with modified Fermi filter and inverse Chebyshev filter, Chebyshev filter, Elliptic filter and Butterworth filter. Firstly, in comparison to the results, the radiologist confirmed that modified Fermi filter was best decision for boundary of the rheumatoid arthritis images. The number of the black voxels of the histogram showed the quantity of the results. At the proposed filter images, numbers of the blacks voxels were statistically decreased. That meant voxels only appeared the black color were changed to others voxels color. Because the number of the total voxels was fixed, the area appeared block color could be effected to the other areas. If the modified Fermi filter were used for rheumatoid arthritis patient, the result will be better than other filters.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.5
• /
• pp.128-132
• /
• 2017

In this thesis, a BPF(band-pass filter) at the center frequency of 2.14GHz, and bandwidth of 20MHz is designed and implemented using high Q dielectric resonators with ${\varepsilon}_r=38$. The DR(dielectric resonator) is resonated by $TE_{01{\delta}}$-mode and it has a hole in the center of DR. The BPF consists of 6-poles dielectric resonators and the characteristic of elliptic function is obtained by non-adjacent coupling. It has the average insertion loss of 0.97dB and the return loss over 25dB in its passband. In this thesis, the frequency selectivity is more improved by the coupling characteristics between non-adjacent resonators than that of dielectric resonator filters with a Chebyshev response.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.6 no.4
• /
• pp.286-292
• /
• 2006

This paper presents the design of a low-voltage wide-band switched-capacitor (SC) filter for wireless communication receiver applications. The filter is the 5th-order Elliptic lowpass filter. With the clock frequency of 50MHz implying that an effective sampling frequency is 100MHz with double sampling scheme, the cut-off frequency of the filter is programmable to be 1.25MHz, 2.5MHz, 5MHz and 10MHz. For low-power systems powered by a single-cell battery, the SC filter was elaborately designed to operate at 1.2V power supply. Simulation result shows that the 3rd-order input intercept point (IIP3) can be up to 27dBm. The filter was fabricated in a $0.25-{\mu}m$ 1P5M standard CMOS technology and measured frequency responses show good agreement with the simulation ones. The current consumption is 34mA at a 1.2V power supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.2
• /
• pp.184-191
• /
• 1993

Continuous-time integrated filters, implemented in MOS VLSI technology, have been receiving considerable attention. In this paper, a continuous-time fifth order elliptic low-pass MOSFET-C filter has been designed with a cutoff frequency 3,400Hz. First an active RC filter is designed using cascade method which each block can be tunable. And then the resistors of an active RC network are replaced by a linear resistor using NMOS depletion transistors operated in the triode region. This continuous-time MOSFET filter have simpler structure than switched-capacitor filter, so reduce the chip area. The designed MOSFET-C filter characteristics are simulated by PSPICE program.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.5
• /
• pp.506-512
• /
• 2003

An output multiplexer of manifold type is widely used in a recent satellite transponder f3r its mass and volume reduction. For correct operation, the filter of such a multiplexer must be singly terminated. In this paper, a simple synthesis method of a 6-pole dual-mode singly terminated filter is described. From the transfer function of the filter, network parameters such as in/output terminations and coupling matrix are obtained with the aid of orthogonal projection and plane rotation. The rotation order, pivot, and rotation angle of the plane rotation process are given for easy filter synthesis. Two different-structure filters are taken into consideration and the network parameters of each filter have been obtained from the same transfer function. The method described in this paper can be applied to the other degree singly terminated filter.

• Journal of Satellite, Information and Communications
• /
• v.1 no.2
• /
• pp.63-70
• /
• 2006

This paper presents the results of Ka band qualification model multiplexers for COMS Payload to be launched in 2008. These are the input and output multiplexers of the satellite transponder to use available frequency resources effectively and the diplexer of the satellite antenna to use the same reflector for both transmitting and receiving frequency bands, respectively. The input multiplexer with four frequency channels has four(4) independent channel filters which consist of an 8-pole elliptic band-pass filter for high frequency selectivity and a 2-pole equalizer for group delay equalization. For low insertion loss, mass and volume reduction, manifold type os employed for output multiplexer. E-plane T-junction is used for either splitting or combining a frequency band into two sub-bands. Asymmetric inductive irises are used to tune the receiving filter easily. The electrical performance and environmental test such as vibration test, mechanical shock test, thermal vacuum test and EMC test are performed and the results of all qualification model multiplexers are compliant to the requirement of each multiplexer. Followed by this qualification, the flight model equipment will be developed.