• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• v.2 no.2
• /
• pp.169-179
• /
• 1998

This paper was performed to estimate interrelations between humus level of sediments and nutrient release from sediments in Dae-cheong reservoir. For investigations, sediments were sampled in June and October, in 1997 at fish farms, embayment, and the main stream of Dae-cheong reservoir. Items for investigation are as follows; water content, weight loss on ignition(IG), porosities of sediments, contents of element such as hydrogen, nitrogen, carbon, and nutrient release rates. Water contents and porosities were measured to conjecture the physical trait and grain size trait. Weight loss on ignition was measured to determine the contents of organic substance. For determination of the humus level of sediments, carbon and nitrogen contents were measured by elemental analyzer. As a result of elemental analysis, C/N ratio was determined in the range of $3.0\~13.1$. From the elemental analysis, humus level of Dae-cheong reservoir sediment was estimated from mesohumic state to oligotrophic state. For the determination of nutrient release rate, $PO_4-P$ and $NH_4-N$ concentrations of interstitial water and overlying water were measured. By using the concentration difference between interstitial water and overlying water and using the Fick's diffusion law, the release rates of phosphorus and nitrogen from the sediment samples were calculated. Release rates of nutrients which directly influence to the water quality were $0.05\~8.63mgP/m^2day$ and $4.99\~36.56mgP/m^2day$. It was found that release rate was measured higher in the 1st sampling period than in the 2nd sampling period. For the determination of phosphorus content in sediment, TPs were measured in 807\~1542{\mu}g/g$ in the 1st samling period and $677\~5238{\mu}g/g$ in the End samling period. Phosphorus release rate and phosphorus content were not interrelated each other.

• Journal of Radiation Protection and Research
• /
• v.28 no.3
• /
• pp.165-172
• /
• 2003

Humic acids present in the soils at the vicinity of domestic atomic power plants(NPPs), located in Yeongkwang(YK), Uljin(UJ), Kori(KR), Koseong(KS), Wolseong(WS) area were isolated, and characterized using elemental analysis and UV/Vis, IR, CPMAS $^{13}C$ NMR spectroscopic methods. The characteristics were compared with one another and with commercial humic acid (Aldrich Co.). Molecular size distributions of the humic acids were determined using a stirred cell ultrafiltration technique. The results of elemental analysis showed that soil humic acid from UJ contains higher oxygen content than humic acids from KR and KS (O/C ratios: 0.51 (UJHA) us. 0.45(KRHA), 0.43(KSHA)). The molecular size distribution revealed that the soil humic acids of UJ and YK contained a higher percentage of larger molecules of > 30,000 daltons, compared to those of KR and KS. The spectral features obtained from UV/vis., IR and CPMAS $^{13}C$ NMR showed that the aromatic character and oxygen containing functional groups in the humic acids from UJ and YK were relatively higher than those of KR and KS. These results indicate that the soil humic acids from UJ and YK were in a higher degree of humification, which may suggest higher affinity of the humic acids with radionuclides released in the soil environments.

• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.1
• /
• pp.28-40
• /
• 2015

To investigate the seasonal variations of carbonaceous aerosol in Daejeon, OC (organic carbon), EC (elemental carbon) and WSOC (water soluble organic carbon) in $PM_{2.5}$ samples collected from March 2012 to February 2013 were analyzed. $PM_{2.5}$ concentrations were estimated by the sum of organic matter ($1.6{\times}OC$), EC, water-soluble ions ($Na^+$, $NH_4{^{+}}$, $K^+$, $Mg^{2+}$, $Ca^{2+}$, $Cl^-$, $SO_4{^{2-}}$, $NO_3{^{-}}$). The estimated $PM_{2.5}$ concentrations were relatively higher in winter ($29.50{\pm}12.04{\mu}g/m^3$) than those in summer ($13.72{\pm}6.92{\mu}g/m^3$). Carbonaceous aerosol ($1.6{\times}OC+EC$) was a significant portion (34~47%) of $PM_{2.5}$ in all season. The seasonally averaged OC and WSOC concentrations were relatively higher in winter ($6.57{\times}3.48{\mu}gC/m^3$ and $4.07{\pm}2.53{\mu}gC/m^3$ respectively), than those in summer ($3.07{\pm}0.8{\mu}gC/m^3$, $1.77{\pm}0.68{\mu}gC/m^3$, respectively). OC was correlated well with WSOC in all season, indicating that they have similar emission sources or formation processes. In summer, both OC and WSOC were weakly correlated with EC and also poorly correlated with a well-known biomass burning tracer, levoglucosan, while WSOC is highly correlated with SOC (secondary organic carbon) and $O_3$. The results suggest that carbonaceous aerosol in summer was highly influenced by secondary formation rather than primary emissions. In contrast, both OC and WSOC in winter were strongly correlated with EC and levoglucosan, indicating that carbonaceous aerosol in winter was closely related to primary source such as biomass burning. The contribution of biomass burning to $PM_{2.5}$ OC and EC, which was estimated using the levoglucosan to OC and EC ratios of potential biomass burning sources, was about $70{\pm}15%$ and $31{\pm}10%$, respectively, in winter. Results from this study clearly show that $PM_{2.5}$ OC has seasonally different chemical characteristics and origins.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03a
• /
• pp.18-21
• /
• 1999

The wrinkling of thin sheet metal induced by compressive instability is one of major defects in sheet metal forming processes. compressive instability is influence by many factors such as mechanical properties of the sheet material geometry of the sheet contact conditions and plastic anisotropy. The analysis of compressive instability in a plastically deforming body is rather difficult because the effects of the above-mentioned factors are rather complex and the instability behavior may show swide variations even for small deviations of the factors. in this work the bifurcation theory is introduced for the finite elemental analysis of the instability behavior of a thin sheet with initially sound geometry and property. All the above-mentioned factors are conveniently considered by the finite element method. The instability limit is found by introducing a criterion scheme into the incremental analysis and the post-bifurcation behavior is analyzed by introducing the branching scheme. Wrinkling initiation and growth in the deep drawing process are analyzed.

• 한국연소학회:학술대회논문집
• /
• 1999.10a
• /
• pp.81-91
• /
• 1999

Fuel characteristics of sewage sludge as required for the fluidized bed incinerators have been evaluated. Sewage sludge is basically a solid fuel with high percentage of moisture. Moisture content of the fuel directly affects the heating value of the fuel and the exhaust gas composition. When the sludge of transported into the incinerator, sludge cake is subject to the mixing, break-up and heat-up. Fluidization process would enhance these physical processes. The sludge fuel could then undergo the moisture evaporation and devolatilization process. Subsequent oxidation of volatiles as well as the remaining char would then follow. Sludge samples are characterized with high percentage of volatiles out of total combustibles. Quantitative understanding of above listed subprocesses would certainly help in the utilization of fluidized bed incinerators. A limited set of fuel characterization tests including calorimetric analysis, proximate analysis, elemental analysis and thermogravimetric analysis were conducted for the selected sludge samples. The measurement reasults of sludge samples were reported along with some published data. Limited experience in the actual incinerator plant is also presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.427-430
• /
• 2001

The degradation characteristics versus MgO Additive for the ZnO ceramic devices fabricated by the standard ceramic techniques is investigated in this study. It were made these devices be basic Matsuoka's composition. Especially, MgO were added to analyze the degradation characteristics and sintered in air at 1300$^{\circ}C$. The conditions of DC degradation test were 115${\pm}$2$^{\circ}C$ for 12h. Using XRD and SEM, the phase and microstructure of samples were analyzed respectively. The elemental analysis in the microstructures was used by EDS, E-J analysis was used to determine ${\alpha}$ . Frequency analysis was accomplished to understand the relationship between R$\sub$g/ and $R_{b}$ with the electric stress at the equivalent circuit.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.3
• /
• pp.182-186
• /
• 2012

This paper aims to analyze the vibration characteristics of the test equipment that inspects any defects in manufactured semiconductor chips and classifies defective chips. This type of equipment should be robust against any vibrations because such vibrations can cause disruption in the process that requires higher precision. 3D model of the structure of the equipment has been used to configure vibration simulation model. Model analysis have been carried out to analyze which part of the equipment is weak against vibration. To minimize the vibration effect of the equipment, the thickness of the plate consist of the equipment and weights are modified. The results show that thicker plate and higher weight in the equipment can decrease vibration effect.

• Macromolecular Research
• /
• v.14 no.4
• /
• pp.443-448
• /
• 2006

A novel ${\beta}$-cyclodextrin derivative (CCD-C) was synthesized with chitosan and carboxymethyl-${\beta}$-cyclodextrin. Its structure was characterized by elemental analysis, infrared spectra analysis, and X-ray diffraction analysis. The adsorption properties for guanosine 5'-monophosphate, cytidine 5'-monophosphate and uridine 5'-monophosphate were studied. Experimental results demonstrated that CCD-C had higher adsorption capability for guanosine 5'-monophosphate, and that the adsorption capacity for guanosine 5'-monophosphate was 74.20mg/g. The adsorption capacity was greatly influenced by pH, time and temperature. The introduction of chitosan enhanced the adsorption ability and adsorption selectivity of ${\beta}$-cyclodextrin for guanosine 5'-monophosphate. This novel derivative of chitosan is expected to have wide applications in the separation, concentration and analysis of nucleotides in biological samples.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.6
• /
• pp.565-572
• /
• 2000

To quantitatively estimate mass contribution of long-range transported yellow sand, their sources should be separated independently from various local soil sources having similar elemental compositions. While it is difficult to estimate total mass loadings of pure yellow sand by traditional bulk analysis, it can be clearly solved by an particle-by-particle analysis. To perform this study, two yellow sand samples and three local soil samples were collected by a mini-volume sampler. These samples were three analyzed using a scanning electron microscope(SEM) equipped with an energy dispersive x-ray analyser (EDX) was used to obtain basic chemical information of individual yellow san particles. A total of 19 elements in a single particle were measured to develop a source profile with newly created homogeneous particle classes (HPCs) as chemical variables. The present study showed that the yellow sand samples as well as three local soil samples were characterized with reasonably well created HPCs. Finally the mass fraction of each HPC in each sample was calculated and then compared each other.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.398-405
• /
• 2002

The degradation characteristics of MgO additive for the ZnO ceramic devices fabricated by the standard ceramic techniques are investigated in this study. These devices were made from basic Matsuoka's composition. Especially, MgO was added to analyze the degradation characteristics and devices were sintered in air at $1200^{\circ}C$. The conditions of DC degradation test were $115\pm2^{\circ}C$ for 12h. Using XRD and SEM, the phase and microstructure of samples were analyzed, respectively. The elemental analysis in the microstructures was performed by EDS, E-J analysis was used to determine $\alpha$. Frequency analysis was accomplished to understand the relationship between $R_G$ and $R_B$ with the electric stress at the equivalent circuit.