• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.2
• /
• pp.213-219
• /
• 2002

A cone-shaped active magnetic healing spindle system for high speed internal grinding with built-in motor that has 7.5kW power and maximum rotational speed of 50,000 rpm is designed and built. Using cone-shaped AMB(Active Magnetic Bearing) system, the axial rotor dick and magnets of conventional 5-axis actuating design can be eliminated. so this concept of design provides a simple magnetic bearing system. In this paper, the cone-shaped electromagnets are designed by magnetic circuit theory, and a de-coupled direct feedback PID controller is applied to control the coupled magnetic bearings. The designed crone-shaped AMB spindle system is built and constructed with a digital control system, which has TMS320C6702 DSP, 16 bit AD/DA, switching power amplifier and gap sensors. As the AMB system provides high damping ratio eliminating overshoot and resonance speed, this spindle runs up to 40,000 rpm stably with about 5${\mu}{\textrm}{m}$ of runout.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.466-469
• /
• 1995

This paper presents a design and performance of the 6 D.O.F linear motion table with a magnetic bearing suspension. The linear positioning of the table with a 150mm stroke is driven by a brushless DC Linear motor and the other attitudes of the stage are controlled by the analog PD controller with magnetic bearing actuators. Each magnetic bearing unit which consists of 3 electromagnets, 3 capacitance probes and 3 backup bearings affords controlled forces by detecting the air gap between the probes and guideways. An integral type capacitance probe amplifier is equipped on the upper plate of the table so that the probe line to the probe amplifier can be shorter therefore the problems due to the stray capacitance and noise can be reduced. Form the pitch-yaw errormeasured by the autocollimator, the vertical and horizont straightness errors of the table are derived that they are maintained below 1.mu. m over 100mm stroke. The positioning accuracy of the linear motion is maintained below 2 .mu. m and the repeatability error is below 1 .mu. m

• Journal of the Korean Society for Railway
• /
• v.13 no.1
• /
• pp.1-8
• /
• 2010

In domestic developing magnetically levitated (Maglev) vehicle, bogie frames install electromagnets which provide the vehicles to run with levitation and guidance forces; moreover, the linear motors used for traction are integrated into the same mechanical structure. This paper presents the process which predicts the evaluation of life cycle for bogie frame on various running conditions. Durability analysis considering vibration effect is simulated by using random loads resulted from dynamic simulation which takes into account the irregularities of guide rail. And it supports additional weak points which were not examined in static analysis.

• Journal of the Korean Magnetics Society
• /
• v.19 no.2
• /
• pp.74-79
• /
• 2009

We have investigated the magnetic education in elementary science of Korea. Text books and other related materials are analysed. Students learn playing with magnets in third grade and learn making electromagnets in sixth grade. Arrangement of topics are in accord with the historical development of electromagnetism in physics although the order is not well suited to other field of science. Teacher's guide books need to be developed to consider various environments in school such as city and country, and rich and poor town. Several details in the science textbook are pointed out for better education. Overall course looks sound.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.997-1001
• /
• 2000

In this paper, the case studies of reducing rotational errors is theoretically done for a grinding spindle with an active magnetic bearing system. The rotational errors acting on the magnetic bearing spindle are due to mass unbalance of rotor, runout, grinding excitation and unmodeled nonlinear dynamics of electromagnets. For the most case, the electrical runout of sensor target is big even in well finished surface, this runout can cause a rotation error amplified by feedback control system. The adaptiveed forward method based on LMS algorithm is discussed to compensate this kind of runout effects, and investigated its effectiveness by numerical simulation and experimental analysis. The electrical runout form the rear sensor target of grind spindle is about 70$\mu\textrm{m}$ with harmonic frequencies. The rotor orbit size in rear bearing is reduced about to 5$\mu\textrm{m}$ due to 1X and 2X rejection by feedforward control.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.3
• /
• pp.236-246
• /
• 2014

This paper presents a hybrid rubber mount with magnet to isolate effectively the vibration in vehicle, forklift, and so on. The hybrid mount does not have any controller of the magnetic force. Dynamic stiffness of the mount is reduced by only magnetic suction according to the applied magnetic field and damping coefficient increased. Performance of conventional rubber mount with using electromagnet has been investigated by MTS Tester. The governing equation of the hybrid mount was derived and verified by comparison with experimental and theoretical results. The equation can be used practically and usefully in the design of the mount and analysis of the mounting system. The hybrid mount provides excellent performance in vibration isolation and its structure is very simpler than active with controller and a semi-active mount with a functional fluid. Furthermore, production cost of the mount using permanent magnets is very lower than that of the active mount with electromagnets. Therefore, commercial potential of the mount is very high.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.4
• /
• pp.395-401
• /
• 2014

Magnetic levitation systems using the attraction force of electromagnets have many constraints according to the variation of air gap and the nonlinearity of electromagnetic force and inductances. As a result of these constraints, the nonlinear control of a magnetic levitation system has been improved by the latest advanced processors and accurate measurement system which can overcome problems such as many constraints and nonlinearity. This paper concentrates on the modeling of a nonlinear magnetic levitation system and an application of an exponential reaching law based sliding mode controller using the exponential reaching law which is one of the most robust controllers against external unexpected disturbances or parameter fluctuations. Controllability of a magnetic levitation system using the sliding mode control algorithm and robustness against parameter fluctuations have been verified through the experimental results.

• The korean journal of orthodontics
• /
• v.20 no.2
• /
• pp.319-331
• /
• 1990

The purpose of this study was to help examining force system, optimal treatment, and prevention of relapse. Orthodontic force was generated by electromagnets, therefore duration could be freely controlled, and applied for 4 days in dogs. Force magnitude was 200gm and 50gm. duration was contious and intermittent. Intermittent duration was divided into 2 kinds of types in on/off, 1 mininute/1 minute, 10 seconds/1 minute. The results were as follows: 1. In the intermittent group to which force was applied for 10 seconds and ceased for 1 minute, osteoclast was not observed. 2. In the intermittent group to which 200gm of force was applied for 1 minute and ceased for 1 minute, there was blood circulation in periodontal space on pressure side, but mild hyalinized zone was observed. 3. More number of total osteoclast was counted in the pressure side of continous group to which 200gm of force was applied than in any other groups. 4. More number of frontal osteoclast was counted in the pressure side of intermittent group to which 200gm was applied for 1 minute and ceased for 1 minute than in any other groups. 5. On tension side, less periodontal space widening, more new bone and secondary cementum formation were observed in the intermittent group to which force was applied for 1 minute and ceased for 1 minute than in the continous group.

• 연구논문집
• /
• s.26
• /
• pp.5-14
• /
• 1996

Test results of electromagnetic suspension (EMS) type urban transit maglev system are reported. Electromagnetic levitation system is a transportation system taking advantage of the attraction of normal conducting electromagnets to support and guide the train in combination with the linear induction traction motors. Urban Transit Maglev (UTM) Which is being developed by the maglev team in KIMM and the Hyundai Precision Company since 1995 consists of three bogies. In the first year, two types of Bogies are developed. Bogie I uses an analog controller for levitation and guidance control and is driven by two linear induction motors (LIM) mounted on the right and left side of module. Bogie II uses a digital controller and is driven by one LIM mounted along the center line of the bogie. Test results reported in this paper are those obtained with Bogie II with a digital controller. Also included in this paper is a brief explanation of the electromagnetic suspension levitation system which is being developed by the maglev team in KIMM.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.813-819
• /
• 2013

The authors have developed a test system for a hemispherical resonator gyroscope by using NI FPGA equipment. We have verified its suitability for the research of resonator gyroscopes through several tests: deriving resonance, controlling amplitudes, and estimating resonator parameters. The authors have adjusted a vibrating pattern to be aligned with the driving axis (or electromagnets). This pattern alignment is a basic and important operation of the FTR mode, which is one of operating modes for resonant gyroscopes.