The effects of substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio on the dielectric constant and optical bandgap of amorphous silicon nitride (a-SiNx:H) thin films prepared by PECVD method using RF glow discharge decomposition of $SiH_{4}$ and $NH_{3}$ gas mixtures have been studied. The dielectric constant and optical bandgap of a-SiNx:H thin films were greatly exchanged as by increasing substrate temperature, RF power, and $NH_{3}/SiH_{4}$ gas flow ratio. The dielectric constant of a-SiNx:H films was increased and optical bandgap of a-SiNx:H films was decreased as the substrate temperature was increased. When the substrate temperature, RF power, gas pressure, $NH_{3}/SiH_{4}$ gas flow ratio, and thickness were $250^{\circ}C$, 20 W, 500 mTorr, 10 and $1500\;{\AA}$, respectively, the dielectric constant, breakdown field and optical bandgap of a-SiNx:H film were 4.3, 1 MV/cm, and 2.9 eV, respectively.
Journal of the Korean Institute of Electrical and Electronic Material Engineers
/
v.18
no.11
/
pp.977-982
/
2005
Al/AlN/n-type 6H-SiC (0001) MIS structures were prepared by AlN layers on vicinal 6H-SiC(0001) substrates with reactive RF magnetron sputtering method. The AlN films were annealed at $900^{\circ}C$, $N_2$ atmosphere lot 1 minutes showed the best result. With XRD analysis, AlN(0002) peak was clearly found. The typical dielectric constant value of the AlN film in the MIS capacitors was obtained as 8.4 from photo C-V. Also, the gate leakage current density of the MlS capacitor was $10^{-10}\;A/cm^2$ order within the electric field of 1.8 MV/cm. Finally, the amount of interface trap densities, $D_{it}$, was evaluated as $5.3\times10^{10}\;eV^{-1}cm^{-2}$ at (Ec-0.85) eV.
Journal of the Institute of Electronics Engineers of Korea SD
/
v.47
no.3
/
pp.51-57
/
2010
A dual-mode direct conversion receiver is developed in $0.13\;{\mu}m$ RF CMOS process for IEEE 802.11n based wireless LAN and IEEE 802.16e based mobile WiMAX application. The RF receiver covers the frequency band between 2.3 and 2.7 GHz. Three-step gain control is realized in LNA by using current steering technique. Current bleeding technique is applied to the down-conversion mixer in order to lower the flicker noise. A frequency divide-by-2 circuit is included in the receiver for LO I/Q differential signal generation. The receiver consumes 56 mA at 1.4 V supply voltage including all LO buffers. Measured results show a power gain of 32 dB, a noise figure of 4.8 dB, a output $P_{1dB}$ of +6 dBm over the entire band.
Proceedings of the Korean Vacuum Society Conference
/
2013.02a
/
pp.365-365
/
2013
본 실험에서는 RF magnetron sputter장비와 evaporator장비를 이용하여 다층박막 IGZO/Ag/IGZO를 제작하였다. 소결된 타겟은 In:Ga:ZnO 1:1:1mol%로 조성된 타겟을 사용하였으며, Ag는 99.999%의 순도를 가진다.다층박막 OMO구조의 Oxide layer는sputter장비를 이용 IGZO막을 제작하였으며, Metal layer는 evaporator 장비를 이용 Ag막을 제작하였다. 변수로는 Metal layer 두께에 따른 구조적, 광학적 특성 변화를 연구하였다. Oxide layer의 RF sputter 공정 조건으로는 초기압력 $3.0{\times}10^{-6}$ Torr 이하로 하였으며, 증착압력 $2.0{\times}10^{-2}$ Torr, RF power 30 W, Ar 50 sccm으로 고정시켰으며, Metal layer의 evaporator 공정조건으로는 $5.0{\times}10^{-6}$ 이하, 전압은 0.3V, 기판 회전속도는 2RPM 두께는 Thickness moniter로 3. 5. 7. 9. 11. 13. 15 nm를 확인하며 증착하였다. 분석결과로는 AFM측정결과 거칠기는 2 nm이하의 거칠기를 확인했으며, XRD측정결과 Bragg's 법칙($2\;dsin{\Theta}=n{\lambda}$)를 만족하는 피크를 찾을 수 없어 비정질 구조임을 확인할 수 있었다. 투과도 측정결과 가시광 영역에서 최대 80% 이상의 투과율을 보여주었으며, IR영역에서는 30% 이하의 투과율을 보여주었다. 에너지 밴드갬 계산결과 4.5~4.6 eV를 갖는 것을 확인하였으며, Low-e 분야에 사용가능함을 보여주었다.
Transactions on Electrical and Electronic Materials
/
v.14
no.2
/
pp.86-89
/
2013
Dye-sensitized solar cells have a FTO/$TiO_2$/Dye/Electrode/Pt counter electrode structure, yet more than a 10% electron loss occurs at each interface. A passivating layer between the $TiO_2$/FTO glass interface can prevent this loss of electrons. In theory, ZnO has excellent electron collecting capabilities and a 3.4 eV band gap, which suppresses electron mobility. FTO glass was coated with ZnO thin films by RF-magnetron sputtering; each film was deposited under different $O_2$:Ar ratios and RF-gun power. The optical transmittance of the ZnO thin film depends on the thickness and morphology of ZnO. The conversion efficiency was measured with the maximum value of 5.22% at an Ar:$O_2$ ratio of 1:1 and RF-gun power of 80 W, due to effective prevention of the electron recombination into electrolytes.
Kim, Jong-Myeong;Lee, Kyoung-Wook;Park, Min-Kyung;Choi, Yun-Ho;Jung, Jae-Ho;Kim, Chang-Wan
Proceedings of the Korean Institute of Information and Commucation Sciences Conference
/
2011.10a
/
pp.402-403
/
2011
This paper has proposed a $0.13-{\mu}m$ CMOS RF Front-end transmitter for LTE-Advanced systems. The proposed RF Front-end supports a band 7 (from 2500 MHz to 2570 MHz) in E-UTRA of 3GPP. It can provide a maximum output power level of +10 dBm but it's a normal output power level is +0 dBm considering a low PAPR. The post-layout simulation results show that the quadrature up-conversion mixer and a driver amplifier consumes 14 mA and 28 mA from a 1.2 V supply voltage respectively, while providing a output power level of 0 dBm at the input power level of -13 dBm.
Sin, Cheon-Sig;Lee, Sang-Uk;Yoon, Dong-Weon;Kim, Jae-Hoon
Journal of Satellite, Information and Communications
/
v.4
no.1
/
pp.36-44
/
2009
The key technologies of GNSS receiver for GNSS sensor station are under development as a part of a GNSS ground station in ETRI. This paper presents the GNSS receiver implementation and signal processing result which is implemented based on FPGA to process the Galileo E1 and E5 signal. To verify the working and performance for GNSS receiver which is implemented based on FPGA, live signal received from GIOVE-B which is second test satellite is used. We gather GIOVE-B signal by using prototyping antenna and RF/IF units including IF-component. To verify Galileo E1 and E5 signal processing function from GIOVE-B, FPGA based signal processing module is implemented as a prototyping hardware board.
AlN(Aluminium Nitride) thin films were prepared using by RF sputtering method on the Si(100) and Si(111) substrates as the parameters of the substrate temperature, RF power, sputtering duration and the $N_2$/Ar ratio and investigated by X-ray diffraction, IR spectrometry, n&k analyzer. For the Si(100) substrate, the AlN thin films of (101) orientation were obtained under the conditions of room temperature and the nitrogen of 60 vol.%. For the Si(111) substrate, the (002) AlN thin films were obtained under the nitrogen of 100 vol.%. In case of the thin film prepared in the condition of above 60 vol.% of the nitrogen, the average value of the surface roughness of the film was 151$\AA$. From the changes of the half widths of E$_1$[TO] phonon bands at the wavenumber of 680$cm^{-1}$ /, it were compared of the crystallinities of the films which were grown under the different conditions. The thicknesses of AlN films were decreased dramatically in the region of the nitrogen of 40~60 vol.%. Its due to the nitridation of the Al target surface and getting low of the sputtering yield by the $N_2$/Ar ratio being increased.
The conventional AC PDP has a relatively low efficiency which is close to 1.5 lm/W. If the AC sustain period is replaced by the RF sustain period, due to oscillating and low electric field, almost 60% of the supplied energy is spent by Xe excitation [1]. The efficiency of RF PDP can be $4{\sim}5$ times higher than that of AC PDP. In this paper, we will present the RF PDP that is a new type of PDP. A new display method in PDP using RF pulses is suggested and applied on a 4-inch-diagonal Panel (hereinafter 4" panel). Even though there were many researches in RF discharge, there was not enough research for display application. Now we propose the RF PDP that is a new display field and we will expect to do more research in this field.
Proceedings of the Korean Vacuum Society Conference
/
2013.02a
/
pp.351-351
/
2013
한국 전체 에너지 사용량 중약 24%의 에너지가 건축물 부분에 소비되고 있다. 건축물의 벽체나 유리창 등을 통해서 에너지 손실이 이루어지는데 유리창은 벽체에 비해 약 10배 이상 낮은 단열 특성을 가지고 있기 때문에 유리창을 통한 열손실량은 더 크다. 이러한 유리창 부분의 열손실 문제를 해결할 수 있는 방안으로 좋은 단열 특성 및 낮은 방사율을 가지고 있는 Low-e coating 방법을 사용하였다. 본 실험에서는 XG glass 기판 위에 IGZO/Ag/IGZO OMO 구조의 다층 박막을 증착하였다. RF magnetron sputtering방법을 이용하여 OMO 구조의 상부와 하부의 Oxide layer로 IGZO 박막을 증착하였다. 사용된 IGZO 타겟은 $In_2O_3$ (99.99%), $Ga_2O_3$ (99.99%), ZnO (99.99%)의 분말을 각각 1:1:1 mol% 조성비로 혼합하여 소결하여 제작하였다. Thermal Evaporator 장비를 이용하여 OMO 구조의 Metal layer로 Ag (99.999%)를 증착하였다. 실험 기판은 크기 $30{\times}30mm$의 0.7T XG glass를 사용하였다. OMO 구조의 산화층 IGZO 박막은 상/하층 동일 조건으로 기판 온도는 실온으로 고정하였으며, 초기 압력 $3.0{\times}10^{-6}$ Torr, 증착 압력 $3.0{\times}10^{-2}$ Torr, RF 파워 50W, Ar 유량 50 sccm로 고정시키고 증착 시간이 변화하면서 박막을 증착하였다. OMO 구조의 Metal layer로 Ag 증착 조건은 초기 진공도가 약 $6.0{\times}10^{-6}$ Torr 이하로 유지하고 기판을 2 Rpm의 속도로 회전시켰다. 이후 0.3 V로 Ag를 10분간 가열하여 충분히 녹인 후 Film Thickness Monitor로 두께를 확인하였다. OMO 다층 박막의 산화물층 변화에 따라 로이다층 박막의 구조적, 광학적 및 전기적 특성을 분석하였다. XRD 분석결과에 의하여 Bragg's 법칙을 만족하는 피크가 나타나지 않는 비정질 구조임을 확인할 수 있으며, AFM 분석결과에 통해서 최소 1.3 nm의 Roughness를 나타내었다. UV-Visible-NIR 분광광도계를 이용하여 다층 박막은 가시광선 영역에서 평균 80%의 광 투과성을 보여 IR 영역에서 평균 30% 투과하고 좋은 차단 특성을 나왔다. Low-e 특성을 갖는 유리창을 통해서 에너지 절약을 이룰 수 있는 것을 확인할 수 있었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.