• Journal of Electrical Engineering and Technology
• /
• v.6 no.3
• /
• pp.408-413
• /
• 2011

In this paper, a real-coefficient approach to Adaptive Frequency Sampling (AFS) technique is developed for efficient equivalent circuit modeling of RF components. This proposed method is advantageous than the vector fitting technique and the conventional AFS method in terms of fewer samples leading to a lower order of a rational function on a given data and to a direct conversion to an equivalent circuit for PSPICE(Personal Simulation Program with Integrated Circuit Emphsis) simulation, respectively. To validate the proposed method, the distributed equivalent circuit of a presented multi-layered RF low-pass filter is obtained using the proposed real-coefficient AFS, and then comparisons with EM simulation and circuit simulation for the device under consideration are achieved.

• Journal of Advanced Navigation Technology
• /
• v.15 no.2
• /
• pp.256-263
• /
• 2011

The nerve impulse is induced by the stimulation of neuron or axon, and this stimulated voltage decays along the propagation distance and time if it is subtreshold potential. This behavior can be estimated using the electrical equivalent circuit because it is very similar to propagation phenomenon of electrical circuit to which Ohm's law is applied. Therefore, I calculated various biometric parameters of body, and then analyzed the propagation behavior of stimulated potential voltage using the distributed parameters of electrical circuit in this paper.

• Current Optics and Photonics
• /
• v.4 no.5
• /
• pp.434-440
• /
• 2020

Based on single-mode rate equations, we present an improved equivalent-circuit model for distributed-feedback (DFB) lasers that accounts for the effects of parasitic parameters and nonradiative recombination. This equivalent-circuit model is composed of a parasitic circuit, an electrical circuit, an optical circuit, and a phase circuit, modeling the circuit equations transformed from the rate equations. The validity of the proposed circuit model is verified by comparing simulation results to measured results. The results show that the slope efficiency and threshold current of the model are 0.22 W/A and 13 mA respectively. It is also shown that increasing bias current results in the increase of the relaxation-oscillation frequency. Moreover, we show that the larger the bias current, the lower the frequency chirp, increasing the possibility of extending the transmission distance of an optical-fiber communication system. The results indicate that the proposed circuit model can accurately predict a DFB laser's static and dynamic characteristics.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.65-67
• /
• 2001

In general, the results of finite element method(FEM) on the analysis of the electrical machines has known as high accuracy but required very long time to calculate the field distribution. Magnetic equivalent circuit(MEC) method can be computing times less than the finite element method and also it provides steady state and transient state simulation. In this paper, describes matrix representation of the winding magneto motive force(MMF) and carry out the distributed the airgap magnetic density takes into account the influence on the stator slots.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.1
• /
• pp.43-49
• /
• 2005

The high rate of voltage rise (dv/dt) in motor terminals caused by high-frequency switching and impedance mismatches between inverter and motor are known as the primary causes of irregular voltage distributions and insulation breakdowns on stator windings in IGBT PWM inverter-driven induction motors. In this paper, voltage distributions in the stator windings of an induction motor driven by an IGBT PWM inverter are studied. To analyze the irregular voltages of stator windings, high frequency parameters are derived from the finite element (FE) analysis of stator slots. An equivalent circuit composed of distributed capacitances, inductance, and resistance is derived from these parameters. This equivalent circuit is then used for simulation in order to predict the voltage distributions among the turns and coils. The effects of various rising times in motor terminal voltages and cable lengths on the stator voltage distribution are also presented. For a comparison with simulations, an induction motor with taps in the stator turns was made and driven by a variable-rising time switching surge generator. The test results are shown.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.115-118
• /
• 2002

This paper presents the design method and performance characteristics of a chip-type quadrature hybrid using LTCC-MLC technology. The design method for a chip-type quadrature hybrid is based on lumped element equivalent circuit of quarter-wave transformer. The chip-type quadrature hybrid was miniaturized to a greater extent using multilayer structure and lumped element. The proposed design method can also reduce the undesirable parasitic effects of the chip-type quadrature hybrid. The proposed chip-type quadrature hybrid was designed and fabricated using the proposed design method and the equivalent circuit model of a quarter-wave transformer. Fabrication and measurement of designed chip-type quadrature hybrid show much smaller size than a conventional distributed quadrature hybrid and a good agreement with simulated results.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1077-1078
• /
• 2006

This paper presents circuit model of catenery in electrified railway system. Most of (a.c.)electrified railway system adopted as AT fed power supply system. This system is fed with twice voltage. It is that AT system can be fed through longer distance. Conventional circuit model of catenary is used T equivalent circuit with lumped parameter. This model may include some problem when traction power supply system is analyzed. In addition, the model with distributed parameter is good for analysis of harmonic and EMI.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1171-1172
• /
• 2007

This Paper presents circuit model of catenery in electrified railway system. Most of (a.c.)electrified railway system adopted as AT fed power supply system. This system is fed with twice voltage. It is that AT system can be fed through longer distance. Conventional circuit model of catenary is used T equivalent circuit with lumped parameter. This model may include some problem when traction power supply system is analyzed. In addition, the model with distributed parameter is good for analysis of harmonic and EMI

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.1
• /
• pp.24-30
• /
• 1991

This paper deals with the analysis of the transient characteristics of a superconducting a.c. generator(SCG) using Finite Element Method. Since the magnetic field induced by the field current and the armature currents are not sinusoidally distributed in a generator, the conventional equivalent circuit method, in general, uses the fundamental component only and is done in frequency domain. But the finite element analysis makes it possible to analyze the transient magnetic field distribution and the electrical characteristics of the double shields of SCG in time domain.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.1
• /
• pp.1-6
• /
• 2002

A new closed-form expressions to calculate frequency-dependent distributed inductance and the associated distributed series resistance of single interconnect on a lossy silicon substrate (CMOS technology) are presented. The proposed analytic model for series impedance is based on a self-consistent field method and the vector magnetic potential equation. It is shown that the calculated frequency-dependent distributed inductance and the associated resistance are in good agreement with the results obtained from rigorous full wave solutions and CAD-oriented equivalent-circuit modeling approach.