• Journal of Welding and Joining
• /
• v.23 no.4
• /
• pp.53-58
• /
• 2005

We designed a weld monitoring system with UV and IR sensors using a embedded DSP controller for implementing a distribution system; running stand alone and communication with outside by industrial standard protocols. Also this system provided a USB port in order to be acquiring data in PC. The user interface program in PC visualized the IR and W data in time, frequency and state space. A correlation of IR and UV signals showed closely related to weld quality. A rapid change of geometry can be found through a moving average filter. And the average value of IR signal at an interval represented a welding width and depth. Through these results, we proposed a monitoring algorithm for a integer type DSP.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.2
• /
• pp.117-124
• /
• 2001

In a SRM drive, the on/off angles of each phase switch should be accurately controlled in order to control to torque and speed in a stable way, The accuracy of the switching angles is dependent upon the resolution of the encoder and the sampling period of the microprocessor. However, as the speed increase, the amount of the switching angle deviation from the preset values is also increased by the sampling period of the microprocessor. Therefore, a low cost encoder suitable for a practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using the simple digital logic circuit is also presented in this paper. It is verified from the experiments that the proposed encoder and logic controller can be a powerful candidate a the practical low cost SRM drive.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.6
• /
• pp.1035-1042
• /
• 2017

In this paper, we implement a public address system using power line communication in order to operate, extend, and expand the complicated public address devices and cables easily. Power line communication based public address system implemented consists of a public address control board and public address speaker boards which are suitable to digital streaming modulation. It can be noticed that we met satisfied results from performance measurement such as maximum audio output, audio channel response time, audio output SNR, and audio output THD+N.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.12 no.5
• /
• pp.473-480
• /
• 2002

The problems of quasi time-optimal digital control are discussed. A new design methodology of quasi time-optimal fuzzy controllers based on approximation of prototype discrete controller is suggested. Four kinds of practicable structures for fuzzy controllers are considered. Examples of computer design of quasi time-optimal fuzzy control systems are given.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.4
• /
• pp.1-5
• /
• 2012

By using LED optical devices and improving the efficiency of optical devices as well as lighting apparatus for humans, LED lighting industry puts the purpose of manufacturing the main products related with information, electric, large-sized LCD BLU, automobile, shipbuilding, agriculture, medical treatment, environment, and telecommunications, etc. Moreover, the main products and the industrial lighting products are manufactured with fusion, as the result, LED lighting industry provides various effects as well as sources of technology based on practical use of LED technology in order to develop the industry from the perspective of the lower price, the higher efficiency, the higher function, the deeper reliance. In the future, not only the development of new LED technology but also the fusion and combination of digital IT technologies using wire-wireless communication, sensor, controller, and artificial intelligence will be expected to create new industrial fields.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.3
• /
• pp.61-68
• /
• 2012

This paper deals with a fault diagnosis algorithm for open faults in the switching devices of PWM inverter-fed IPMSM (Interior Permanent Magnet Synchronous Motor) drive. The proposed diagnostic algorithm is realized in the controller using the informations of three-phase currents or reference line-to-line voltages, without requiring additional equipments for fault detection. Under switch open fault conditions, the conventional dq model used to control an AC motor cannot directly be applied for the analysis of drive system, since three-phase balanced condition does not hold. To overcome this limitation, a fault model based on the line-to-line voltages is employed for the simulation studies. For comparative performance evaluation through the experiments, the entire control system is implemented using digital signal processor (DSP) TMS320F28335. Simulations and experimental results are presented to verify the validity of the proposed diagnosis algorithm.

• Proceedings of the KIEE Conference
• /
• 2005.04a
• /
• pp.83-86
• /
• 2005

This paper proposed a hydraulic pump system which uses a variable SR drive and constant capacity pump. The base and maximum speed, torque are determined from displacement capacity of the pump and maximum pressure. The drive system is set to have a minimum power consumption having hydraulic preset pressure, which is operated within a maximum capacity and maximum preset pressure. This is achieved by controlling motor speed and power with feedback signal of pressure of the hydraulic pump. A 2.2kw, 12/8-pole SR motor and DSP based digital controller are designed and prototype drive system is manufactured. The proposed variable speed SR drive system is simulated and tested with experimental set-up. The test results show that the system has some good features such as high efficiency and high response characteristics.

• Journal of Power Electronics
• /
• v.3 no.3
• /
• pp.167-174
• /
• 2003

In a switched reluctance motor drive, it is important to synchronize the stator phase excitation with the rotor position, because the position of rotor is an essential information. Although high resolution optical encoders or resolvers are used to provide a precise position information, these sensors are expensive. Moreover, in the high-speed region, switching angles are fluctuated back and forth out of the preset value, which is caused by the sampling period of the microprocessor. In this paper, a low cost analog encoder suitable for practical applications is proposed. And the control algorithm to generate switching signals using a Simple digital logic is presented. The validity of the proposed analog encoder with a proper logic controller is verified from the experiments.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.336-339
• /
• 2005

This paper presents a PM type BLDC(Brushless DC) Motor servo drive system using high performance DSP TMS320F2812. The DSP controller with 150MIPS enables an enhanced real time implementation and increased efficiency and high performance for motor drive. The suggested drive system consists of PI action for the constant speed control and PID action for the current control with only 3 Halls, no encoders. The developed servo drive control system shows a good response speed characteristics at high speed up to 10000 [rpm].

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.366-369
• /
• 2005

The smelting system using induction heating technology has many advantages over conventional fossil fuel regarding energy efficiency, environmental aspect and so on. This paper introduces the principal and technical trends of Induction heating technology, and describes recently developed 2500kW induction smelting inverter, The developed inverter is a series resonant type using high speed Thyristor (SCR) and employs state-of-art digital controller using DSP.