• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.91-94
• /
• 1997

$\alpha$-sexithienyl($\alpha$-6T) thin films were deposited by Organic Molecular Beam Deposition(OMBD) technique, where the $\alpha$-6T was synthesized and purified by the sublimation method. The thin films of the $\alpha$-6T were deposited under various deposition conditions. The effects of deposition rate, substrate temperature. and vacuum pressure an the formation of these films have been studied. The molecular orientations of $\alpha$-6T films were investigated with the polarized electronic absorption spectroscopy. The molecules in the $\alpha$-6T film deposited at a low deposition rate under a high vacuum were aligned almost perpendicular to the substrate. The film deposited at an elevated substrate temperature (~9 $O^{\circ}C$) showed higher conductivity than the film deposited at room temperature.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.9
• /
• pp.388-394
• /
• 2003

Many toxic pesticides as aqueous-base sprays are dispensed for protection of food crops from pests into farm fields. When dispensed with conventional nozzles, a large portion of the spray is often lost by airborne drifts of droplets away and lack of deposition onto the plants due to rapid gravitational settling of droplets to the soil beneath. And target deposition efficiencies poorer than 20％ are often encountered in agricultural pesticides. An electrostatic spraying technology offers a very favorable means to increasing pesticides droplets deposition onto biological surfaces of living crops. In this paper a corona type spray nozzle, utilizing a set of corona charging devices and a pulsed droplet-charging voltage applied, has been proposed and tested its potential experimentally. As a result, it exhibits a large current deposition of aqueous pesticide sprays on the sensing target, which, however, promise to be as one of the effective electrostatic spraying nozzle.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.567-570
• /
• 2010

With continuously increasing flat panel display size, uniformity of thin film deposition has been drawing more attentions and associated fabrication methodologies are being actively investigated. Since the convective flow field of mixture gas plays a significant role for deposition characteristics of thin film in an APCVD system, it is greatly important to maintain uniform distribution and consistent concentration of mixture gas species. In this paper, computational study has been performed for the improvement of flow uniformity of mixture gas in an APCVD reactor during thin film deposition process. A diffuser slit has bee designed to spread the locally concentrated gas flow exiting from the flow distributor. A uniform flow distributor has been developed which has less dependency on operating conditions for global flow uniformity

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.5
• /
• pp.44-50
• /
• 2011

The effect of deposition time in arc ion plating on surface properties of the TiN-coated SM45C steel is presented in this paper. The surface roughness, micro-particle, micro-hardness, coated thickness, atomic distribution of TiN, and adhesion strength are measured for various deposition times. It has been shown that the deposition time has a considerable effect on the micro-hardness, the coated thickness, and the atomic distribution of TiN of the SM45C steels but that it has little influence on the surface roughness and adhesion strength.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.279-282
• /
• 2002

In this paper, we discuss influence of process condition on contact resistance in WSix deposition process. In the WSix deposition process, we confirmed that word line to bit line contact resistance(WBCR) due to temperature of word line WSix deposition among various process condition split experiment. RTP treatment, d-poly ion implantation dose and thickness was estimated a little bit influence on contact resistance. Also, life time of shower head in the process chamber for WSix deposition related to contact resistance. The results obtained in this study are applicable to process control and electrical characteristics for high reliability and high density DRAM's.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.40 no.7
• /
• pp.670-674
• /
• 1991

This paper presents the material properties of LPCVD silicon films formed using Si2H6 gas at various deposition temperatures. To study the structural properties depending on the deposition temperature, XRD, EBD and TEM analyses were used. The maximum grain size in this experiment was obtained at the deposition temperature of 485ø C. It is discussed that LPCVD films formed below the deposition temperature of 485ø C are promising for low temperature TFT applications. The enhancement of the film characteristics results from the reduction of grain boundary density. We also observed that the film properties of Si2H6 at 600ø C was quite different from those of Si H4 at 600ø C. It has shown that the grain structure from a TEM analysis was elliptical and not dependent on the deposition temperature.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.12
• /
• pp.560-564
• /
• 2006

ZnO thin films were prepared by RF magnetron sputter deposition on p-Si(100) wafer with various cooling rates of substrate temperature such as the substrates were pre-heated to $400^{\circ}C$ before the deposition and then cooled down naturally or slowly to $300^{\circ}C,\;200^{\circ}C,\;100^{\circ}C$, and R.T. by the temperature controller during the deposition. Crystalline and micro-structural characteristics of the films were investigated by XRD and SEM. ZnO films which cooled down naturally or slowly by the temperature controller during the deposition, especially the film were deposited with cooling down from $400^{\circ}C\;to\;200^{\circ}C$ slowly. showed the most outstanding c-axis preferred orientation.

• Journal of the Korean Ceramic Society
• /
• v.21 no.2
• /
• pp.156-164
• /
• 1984

The characteristic of pyrolytic carbon deposited in a fluidized bed as measured by density apparent crystallite size and viewed metallographically under polarized light can be easily controlled by adjusting the deposition parameters such as deposition temperature and propane flow rate or silicon content. The density of isotopic pyrolytic carbons deposited from propane between 120$0^{\circ}C$ and 140$0^{\circ}C$ increases with increasing propane flow rate and decreasing deposition temperature from 1, 73g/cc to 2.08g/cc. The apparent crystallite size Lc parameter appears to depend only on deposition temperature being entirely independent of the propane flow rate. The carbon matrix density of the silicon-alloyed carbonds deposited from propane and methyltrichlorosil-ane from 2.05g/cc for a silicon content around 9wt% to 2.67g/cc for a silicon content of 36.7wt% The Lc parameter of the deposition temperature being entirely independent of the silicon content.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.561-564
• /
• 1987

The deposition and reflow properties or BPSG film deposited by APCVD was characterized by variation of each process parameter. As deposition temperature is increased higher, deposition rate is decreased. Maximum deposition rate of BPSG film is obtained in higher 02/Hyride ratio than CVD Oxide or PSG. BPSG film shows stable dielectric properties and we obtained good planarization effect at lower reflow temperature in case of BPSG film than PSG film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.224-227
• /
• 1999

Ferroelectric Pb(Zr$\sub$0.52/Ti$\sub$0.48/)O$_3$ thin films were fabricated by pulsed laser deposition, mainly varying process conditions such as substrate temperature, oxygen pressure, and laser energy, PZT films annealed at more than 600$^{\circ}C$ were crystallized into pure perovskite phases regardless of deposition temperatures. Lower deposition temperature of 400$^{\circ}C$ accompanied with post-annealing at 650$^{\circ}C$ resulted in denser microstructures with extremely small grains compated to those of thin films annealed at higher deposition temperatures. Hysteresis curves of thin film with small grains exhibitied good squareness and low leakage characteristics.