• Corrosion Science and Technology
• /
• 제14권4호
• /
• pp.161-165
• /
• 2015

This paper presents an analysis of thermal stress induced along the interface between a polymeric coating layer and a steel substrate as a result of uniform temperature change. The epoxy layer is assumed to be a linear viscoelastic material and to be theromorheologically simple. The viscoelastic boundary element method is employed to investigate the behavior of interface stresses. The numerical results exhibit relaxation of interface stresses and large stress gradients, which are observed in the vicinity of the free surface. Since the exceedingly large stresses cannot be borne by the polymeric coating layer, local cracking or delamination can occur at the interface corner.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1779-1783
• /
• 2006

The hybrid thin-film (HTF) passivation layer composed of the UV curable acrylate layer and MS-31 (MgO:SiO2=3:1wt%) layer was adopted in organic light emitting diode (OLED) to protect organic light emitting materials from penetrations of oxygen and water vapors. The moisture resistance of the deposited HTF layer was measured by the water vapor transmission rate (WVTR). The results showed that the HTF layer possessed a very low WVTR value of lower than $0.007g/m^2$ per day at $37.8^{\circ}C$ and 100% RH. Therefore, the HTF on the OLED was found to be very effective in protect what from the penetrations of oxygen and moisture.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1046-1049
• /
• 2006

We proposed a simplified fabrication structure and method which can provide separate Red (R), Green (G), Blue (B), and White (W) OLED pixels with 2 metal-mask changes in emitting layer fabrication inspired from the structure of multi-layer white OLED and carrier blocking mechanism. A red emission layer for the R and W pixel with 1st mask, and then a blue emission layer with hole blocking layer for the B and W pixel with 2nd mask, and finally a common green emission layer were deposited sequentially. We expect that this concept would be very useful to the actual fabrication of multi-color OLED display although additional optimization is needed.

• Transactions on Electrical and Electronic Materials
• /
• 제11권5호
• /
• pp.222-225
• /
• 2010

The preparation of tin oxide thin films by atomic layer deposition (ALD), using a tetrakis (ethylmethylamino) tin precursor, and the effects of a seed layer on film growth were examined. The average growth rate of tin oxide films was approximately 1.2 to 1.4 A/cycle from $50^{\circ}C$ to $150^{\circ}C$. The rate rapidly decreased at the substrate temperature at $200^{\circ}C$. A seed effect was not observed in the crystal growth of tin oxide. However, crystallinity and the growth of seed material were detected by XPS after thermal annealing. ALD-grown seeded tin oxide thin films, as-deposited and after thermal annealing, were characterized by X-ray diffraction, atomic force microscopy and XPS.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 E
• /
• pp.1840-1842
• /
• 1997

MgO protection layer on the dielectric layer in PDP prevents a dielectric layer from sputtering and lowers the firing voltage due to a large $\gamma$-Coefficients. Until now, the MgO protection layer is mainly prepared by E-beam evaporation. However, there are some problems that is easy pollution and change of its characteristics with time and delamination. Therefore in this study. MgO protection layer is prepared on dielectric layer by R.F. magnetron sputtering with Mg target under various conditions. The sputtered MgO shows the better discharge characteristics compared with MgO deposited by E-beam evaporatior.

• ETRI Journal
• /
• 제34권2호
• /
• pp.280-283
• /
• 2012

By inserting $H_2O$ treatment steps during atomic layer deposition of a ZnO layer, the turn-on voltage shift from negative bias stress (NBS) under illumination was reduced considerably compared to that of a device that has a continuously grown ZnO layer without any treatment steps. Meanwhile, treatment steps without introducing reactive gases, and simply staying under a low working pressure, aggravated the instability under illuminated NBS due to an increase of oxygen vacancy concentration in the ZnO layer. From the experiment results, additional oxidation of the ZnO channel layer is proven to be effective in improving the stability against illuminated NBS.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.459-460
• /
• 2008

Zinc oxide micro rods were fabricated using as chemical bath deposition ok photolithography. Vertically aligned Zinc Oxide rod array as grown by chemical bath deposition method on Zinc Oxide template layer. The ZnO template layer was deposited on glass and the pattering was made by standard photolithography technique. The selective growth of ZnO micro rods were achieved with the masked ZnO template layer substrate. The fabricated ZnO micro rods were found to be single crystalline and have grown along hexagonal c-axis direction of (0002) which is same as the preferred growth orientation of ZnO template layer. The ZnO micro-rod array structure was implemented as a window layer in Cu(InGa)Se2 solar cell and its effect on photovoltaic efficiency was examined.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.958-961
• /
• 2007

The electrical characteristics of organic thin-filmtransistor (OTFTs) can be improved by inserting adhesion layer on gate dielectrics. Adhesion layer was used as polymeric adhesion layer deposited on inorganic gate insulators such as silicon dioxide $(SiO_2)$ and it was formed by vapor deposition polymerization (VDP) instead of spin-coating process. The OTFTs obtained the on/off ratio $of{\sim}10^4$, threshold voltage of 1.8V, subthreshold slop of 2.9 V/decade and field effect mobility about $0.01\;cm^2/Vs$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.87-87
• /
• 2010

We report a new patterning technique of inorganic materials by using thin-film transfer printing (TFTP) with atomic layer deposition. This method consists of the atomic layer deposition (ALD) of inorganic thin film and a nanotransfer printing (nTP) that is based on a water-mediated transfer process. In the TFTP method, the Al2O3 ALD growth occurs on FTS-coated PDMS stamp without specific chemical species, such as hydroxyl group. The CF3-terminated alkylsiloxane monolayer, which is coated on PDMS stamp, provides a weak adhesion between the deposited Al2O3 and stamp, and promotes the easy and complete release of Al2O3 film from the stamp. And also, the water layer serves as an adhesion layer to provide good conformal contact and form strong covalent bonding between the Al2O3 layer and Si substrate. Thus, the TFTP technique is potentially useful for making nanochannels of various inorganic materials.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 디스플레이 광소자 분야
• /
• pp.53-56
• /
• 2002

The effect of $\alpha$-septithiophene (${\alpha}-7T$) layers on the organic light emitting diode(OLED) was studied. The ${\alpha}-7T$ was used for a buffer layer in OLED. Hole injection was investigated and improved emission efficiency. The OLEDs structure can be described as indium tin oxide(ITO)/ buffer layer / hole transporting layer / emitting layer / electron transporting layer / LiF / Al. The hole transporting layer were composed of N,N-diphenyl-N,N-di(3-methylphenyl)-1,1-biphenyl-4,4-diamine(TPD), and N,N-di(naphthalene-1-ly)-N,N-diphenyl-benzidine( ${\alpha}$-NPD). The emitting layer, and electron transporting layer consist of tris(8-hydroxyquinolinato) aluminum($Alq_3$). All organic layer were deposited at a background pressure of less than $10^{-6}$ torr using ultra high vacuum (UHV) system. The ${\alpha}-7T$ layer can substitute the hole blocking layer, and improve hole injection properties.