• 제목/요약/키워드: crusher

검색결과 121건 처리시간 0.029초

Impact crushing에 대한 고찰 -Quarry Management and Products, 76년 2월호-

  • Farahar R M
    • 시멘트
    • /
    • 통권64호
    • /
    • pp.11-16
    • /
    • 1976
  • 암석 파쇄시 최대의 효과를 얻기 위해서는 암석의 물리적, 화학적 특성 및 size 등을 고려하여 최적의 crusher를 선택해야 함을 감안하여 crusher의 일종인 impact crusher의 구조 및 파쇄원리, 파쇄효과, 경제성 검토결과 등을 수록, crusher의 선택 및 광산 운영에 참고케 하고자 한다.

  • PDF

연자방아의 원리를 이용한 다기능 파쇄기 개발 (Development of multi crusher system using the principle of the Yeon-Ja-Bang-A)

  • 조현철;천세영;안태규;양순용
    • 한국공작기계학회:학술대회논문집
    • /
    • 한국공작기계학회 2004년도 춘계학술대회 논문집
    • /
    • pp.215-218
    • /
    • 2004
  • This paper is about a study of development on multi crusher system. This system use the principle of the Yeon-Ja-Bang-A. This system consists of the power part and the power transmit part, the Yeon-Ja Stone part, the crusher part, an input part, an output part. The advantage of this system decrease about working hours and installation aera.

  • PDF

봉파쇄기에 의해 제조된 재생굵은골재를 사용한 콘크리트의 공학적 특성 (Engineering Properties of Concrete Using Recycled Aggregate Manufactured by Bar-Crusher)

  • 백대현;한동엽;유명열;이건철;한천구
    • 한국건축시공학회:학술대회논문집
    • /
    • 한국건축시공학회 2006년도 추계 학술논문 발표대회 논문집
    • /
    • pp.83-86
    • /
    • 2006
  • This study investigates engineering properties of concrete using recycled coarse aggregated manufactured by bar-crusher. Test showed that Bar-crusher(S) had more effective results at fresh state than cone-crusher(C) and impact-crusher(I). In case of specimens manufactured by S, increase of spindle velocity, incorporating ratio of recycled aggregate and maximum size of aggregate inclined fluidity. As for the hardened concrete, compressive strength of specimens by C or I exhibited lower value than that of S. In addition, specimens using recycled aggregate manufactured by 400rpm and 500rpm of spindle velocity showed less than 10% reduction rate of strength, which is not significant reducing value. It is found that 500rpm of the spindle velocity had the best strength performance, while 600rpm was the worst. Strength value of specimens decreased as incorporating ratio of recycled aggregate inclined, but the strength value of most specimens exhibited less than 10% of reducing rate, assuming favorable result, only at less than 25% incorporating ratio of recycled aggregate.

  • PDF

파쇄 메카니즘과 파쇄회로에 따른 입도분포 (Particle-Size Distribution Dependent upon Crushing Mechanism and Crushing Circuit)

  • 최도영;김완태;김상배
    • 한국광물학회지
    • /
    • 제23권4호
    • /
    • pp.297-303
    • /
    • 2010
  • 본 연구에서는 파쇄 메커니즘이 상이한 파쇄기(함마 크럿셔와 롤 크럿셔)와 파쇄회로(개회로 및 폐회로)를 사용하여 각각의 파쇄기 종류에 따른 백운석 파쇄산물의 입도분포와 파쇄특성에 대해 알아보았다. 함마 크럿셔로 파쇄한 경우, 100 mesh 이하의 미분이 약 34 wt.%로 롤 크럿셔로 파쇄한 경우보다 약 3 배 이상 높았다. 또한 14~25 mesh 산물은 롤 크럿셔로 파쇄할 경우, 함마 크럿셔로 파쇄한 경우에 비하여 약 20 wt.% 이상 많이 생성되었다. 35 mesh 이하의 산물은 함마 크럿셔로 파쇄 시 전체의 약 80 wt.% 정도였다. 두 파쇄기 모두 개회로에 비해 폐회로 파쇄 시 미분의 발생률이 감소하였다. 광석에 따른 적절한 파쇄기 및 파쇄회로의 선택에 따라 목적하는 입도의 산물을 효율적으로 얻을 수 있다.

The Characteristics of pulverized Powder by Automatic Tablet Crusher

  • Doh, Seong-Tak;Kim, Sung-Hwan;Lee, Do-Young;Kwon, Oh-Ju
    • 대한의생명과학회지
    • /
    • 제8권2호
    • /
    • pp.101-106
    • /
    • 2002
  • The purpose of this study was to test the capacity of automatic tablet crusher. The Automatic tablet crusher not only saved crushing time, but also removed floating fine powders that was occurred during crushing and caused allergy. The characteristics of powder produced by this crusher were as follows: First, to meet the condition as powder after pulverizing 5∼10 g tablet it took 6 to 12 seconds crushing time. But six seconds would do to get powder f3r oral administration. Second, when the quantity of medicine was measured by HPLC, powder from automatic crusher showed higher than that from pestle. HPLC chromatogram indicated that there was no change of medicine in the process of pulverization.

  • PDF

공기(또는 물) 스프레이형 폐스치로폼 분쇄기 (Scrapped styrofoam crusher with sprayed air (or water))

  • 고관영;김병수;이찬우
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2008년도 춘계학술대회 논문집
    • /
    • pp.469-472
    • /
    • 2008
  • This research suggest one-body type scrapped styrofoam crusher with sprayed air (or water), which at present separately composed of dust eliminator, air supplier and crusher. Air (or water) that supplied from compressor injected to rotating twin roller through axis hole, and sprayed out of fine hole on the surface. The crusher that manufactured with sprayed air (or water) can make high-quality primary styrofoam removed pollution and dust. In case of mixed sprayed air and water, clean degree of crushed styrofoam was higher than single sprayed air. This could be contributed to reduce environmental pollution, cost and space in standpoint of recycling scrapped styrofoam.

  • PDF

쇄석기의 충격하중 정량화에 대한 연구 (A Study on the Impact Load Quantification of the Jaw Crusher)

  • 홍성주;양해정
    • 드라이브 ㆍ 컨트롤
    • /
    • 제16권2호
    • /
    • pp.1-7
    • /
    • 2019
  • Jaw crusher is a device that breaks rock collected from mines or quarries to produce aggregates of the size desired by user. A representative method for measuring load is to measure them by attaching force sensors directly to the part where the load is generated. However, the direct method has many limitations such as high-impact loads generation in equipment or space constraints, sensor capacities and costs. Therefore, Transfer Path Analysis (TPA) was used to indirectly measure impact loads by attaching acceleration sensors. In this study, both direct and TPA methods were used to measure the impact load of Jaw crusher. This study finally quantifies the impact of the load generated by the Jaw crusher using direct method and TPA method, and comparing the impact load measured calculated the derive the error rate.

콘 크러셔의 전달 하중 및 기여도 분석 (Transfer Force and Contribution Analysis of Cone Crusher)

  • 김대지;정진태;;이창선;송창헌
    • 드라이브 ㆍ 컨트롤
    • /
    • 제19권4호
    • /
    • pp.77-84
    • /
    • 2022
  • The aims of this study was to estimate transfer force delivered to cone crusher housing and contribution of force transmission. The rock crushing condition caused vibrations in the cone crusher housing, which were experimentally measured, and frequency response functions (FRF) were also found through modal impact tests. Vibration data and frequency response functions were applied to the transfer path analysis (TPA) model. Next, transfer forces delivered to the cone crusher housing were quantified via the TPA method. Contribution of force transfer was also analyzed based on force estimation results. Finally, this study describes basic concepts and components of the TPA method and reviews its applicability to rotating machinery that experiences impact vibrations and forces.

회전형 마쇄기에 의해 생산된 순환 굵은골재를 사용한 콘크리트의 기초적 특성 (Basic Characteristics of the Concrete using Recycled Coarse Aggregates Produced by a Rolling Crusher)

  • 송일범;백대현;손근성;신영인;한민철;한천구
    • 한국콘크리트학회:학술대회논문집
    • /
    • 한국콘크리트학회 2010년도 춘계 학술대회 제22권1호
    • /
    • pp.249-250
    • /
    • 2010
  • 본 연구에서는 회전형 마쇄기에 의해 생산된 순환굵은 골재의 우수성을 입증하기 위하여 콘크리트의 기초적 특성을 콘크러셔를 사용한 경우와 비교 분석 한 것이다. 그 결과 순환골재 치환율이 증가에 따라 회전형 마쇄기에 의해 생산된 순환골재일 수록 콘크러셔에 비해 유동성 및 압축강도면에서 양호한 것을 알 수 있었는데, 이는 회전형 마쇄기에 의해 생산된 순환골재의 입형이 비교적 둥글어 골재사이의 마찰력이 감소한 것 및 마모작용으로 부착모르터가 다량 제거된 것 등에 기인한 것으로 분석된다.

  • PDF