• Nuclear Engineering and Technology
• /
• v.54 no.10
• /
• pp.3855-3863
• /
• 2022

An evaluation of the radiation shielding performance of high-Z-particle-loaded polylactic acid (PLA) composite materials was pursued. Specimens were produced via fused deposition modeling (FDM) using copper-PLA, steel-PLA, and BaSO₄-PLA composite filaments containing 82.7, 75.2, and 44.6 wt% particulate phase contents, respectively, and were tested under broad-band flash x-ray conditions at the Sandia National Laboratories HERMES III facility. The experimental results for the mass attenuation coefficients of the composites were found to be in good agreement with GEANT4 simulations carried out using the same exposure conditions and an atomistic mixture as a model for the composite materials. Further simulation studies, focusing on the Cu-PLA composite system, were used to explore a shield design parameter space (in this case, defined by Cu-particle loading and shield areal density) to assess performance under both high-energy photon and electron fluxes over an incident energy range of 0.5-15 MeV. Based on these results, a method is proposed that can assist in the visualization and isolation of shield parameter coordinate sets that optimize performance under targeted radiation characteristics (type, energy). For electron flux shielding, an empirical relationship was found between areal density (AD), electron energy (E), composition and performance. In cases where ${\frac{E}{AD}}{\geq}2MeV{\bullet}cm{\bullet}g^{-1}$, a shield composed of >85 wt% Cu results in optimal performance. In contrast, a shield composed of <10 wt% Cu is anticipated to perform best against electron irradiation when ${\frac{E}{AD}}<2MeV{\bullet}cm{\bullet}g^{-1}$.

• Resources Recycling
• /
• v.28 no.5
• /
• pp.74-79
• /
• 2019

The effects of equivalent of iron powder, particle size, agitation speed on the removal efficiency of copper ion were investigated by adding iron powder as cementation agents to simulated mine drainage solution with 117.15 mg/L Cu ion. The 50 % of Cu was removed at 90 min with 2 equivalent of iron powder while more than 99 % of Cu was removed at 60 min with 16 equivalent at 200 rpm and $20^{\circ}C$. The removal efficiencies of Cu ion were not different using 2 equivalent of $48{\mu}m$ and $150{\mu}m$ iron powder, and the removal efficiency increased rapidly with increasing the agitation speed to more than 400 rpm. This lower removal efficiency resulted from agglomeration of iron powder observed by SEM, which could reduce the effective specific surface area. More than 99 % of copper ion was removed using 2 equivalent of $48{\mu}m$ iron powder at 60 min, 600 rpm and $20^{\circ}C$.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.29-36
• /
• 2004

In this paper, a new replication technique for a real 3D microstructure was introduced, in which a master Pattern WES made of photo-curable epoxy using a microstereolithography technology, and then it was transferred onto an epoxy-copper particle composite. A helical gear was selected as one of the real 3D microstructure for this study, and it was replicated from a pure epoxy to an epoxy composite. In addition, the transferability of the microreplication process was evaluated, and the properties of :he epoxy composite were compared to that of the pure epoxy, including hardness, wear-resistance and thermal conductivity.

• Journal of Mechanical Science and Technology
• /
• v.16 no.9
• /
• pp.1175-1182
• /
• 2002

The commercial viability of heat exchanger is mainly dependent on its long-term fouling characteristic because the fouling increases the pressure loss and degrades the thermal performance of a heat exchanger. An experimental study was performed to investigate the characteristics of fluid flow and heat transfer in a fluidized bed heat exchanger with circulating various solid particles. The present work showed that the higher densities of particles had higher drag force coefficients, and the increases in heat transfer were in the order of sand, copper, steel, aluminum, and glass below Reynolds number of 5,000.

• Journal of Powder Materials
• /
• v.10 no.5
• /
• pp.337-343
• /
• 2003

Nanostructured Cu-$Al_2O_3$ composite powders were synthesized by thermochemical process. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from water-soluble copper and aluminum nitrates, 2) air heat treatments to evaporate volatile components in the precursor powder and synthesis of nano-structured CuO + $Al_2O_3$, and 3) CuO reduction by hydrogen into pure Cu. The suggested procedures stimulated the formation of the gamma-$Al_2O_3$, and different alumina formation behaviors appeared with various heat treating temperatures. The mean particle size of the final Cu/$Al_2O_3$ composite powders produced was 20 nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/$Al_2O_3$ composite by the conventional internal oxidation process.

• Journal of the Korean Magnetics Society
• /
• v.17 no.2
• /
• pp.99-102
• /
• 2007

The Cu oxide nano powders were synthesized by levitational gas condensation (LGC) method and their high heterogeneous catalytic effects of oxidation of 2,3,5-trimethyl-1,4-hydroquinone (TMHQ) and catalase activity were studied. The nano powders consist of mainly $Cu_2O$. The catalytic effect which was clarified by the oxidation of TMHQ and the activity of catalase, was found to depend on the amount of $Cu_2O$ phase and the particle size.

• Journal of Power System Engineering
• /
• v.5 no.4
• /
• pp.61-66
• /
• 2001

Electro-Rheological(ER) fluids undergo a phase-change when subjected to an external electric field, and this phase-change typically manifests itself as a many-order-of magnitude change in the rheological behavior. This paper presents experimental results on material properties for an ER fluids of arabic gum components subjected to electrical fatigues. As a first step, ER fluids are made of arabic gum 25% of particle weight-concentration. Following the construction of test mechanism for estimated durability of ER fluid, the dynamic yield stress, shear stress and current density of the ER fluids are experimentally distilled as a function of DC electric field. The durability estimation of operated ER fluids are distilled and compared with those of unused ER fluids. In addition, the surface roughness of the employed electrode for copper and aluminum are evaluated as a function of the number of the electric-field cycles.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.243-258
• /
• 2009

Bearingless centrifugal pump systems are employed in the semiconductor, pharmaceutical and medical industries due to their facility for pumping high purity fluids without particle contamination. Two types of forces have to be generated by the stator units, namely bearing forces for achieving magnetic levitation, and drive forces for producing the needed pump torque. The generation of these forces requires bearing and drive windings, which can be realized as separate bearing and drive coils or as identical, combined coils on the stator claws. In this paper, a detailed comparison between these two winding concepts is undertaken, whereby the copper losses, the power electronics losses, and the achievable pump output pressure are evaluated for both concepts. For each criterion a ratio of improvement is calculated analytically which allows evaluation of the performance of the two winding concepts for any given pump operating point and design. Finally, also practical features such as control complexity, cabling effort and manufacturability are discussed and measurements on prototype systems are carried out to validate the considerations.

• KSTLE International Journal
• /
• v.1 no.1
• /
• pp.34-42
• /
• 2000

A method and results of classification of four different metallic wear debris were presented by using their color features. The color image of wear debris was used far the initial data, and the color properties of the debris were specified by HSI color model. Particles were characterized by a set of statistical features derived from the distribution of HSI color model components. The initial feature set was optimized by a principal component analysis, and multidimensional scaling procedure was used fer the definition of a classification plane. It was found that five features, which include mean values of H and S, median S, skewness of distribution of S and I, allow to distinguish copper based alloys, red and dark iron oxides and steel particles. In this work, a method of probabilistic decision-making of class label assignment was proposed, which was based on the analysis of debris-coordinates distribution in the classification plane. The obtained results demonstrated a good availability for the automated wear particle analysis.

• Journal of Powder Materials
• /
• v.1 no.2
• /
• pp.167-173
• /
• 1994

Cu-10wt%W composite powders have been manufactured by a high energy ball milling technique. The composite powders were pressed at 250 MPa and sintered in a dry hydrogen at 103$0^{\circ}C$ for 4 hours. After sintering, Cu-10wt%W composite materials were forged. And the arc-resistance of forged materials which have the same relative density of 94% has been tested. Composite particles, i.e. tungsten particles distributed homogeneously in the copper matrix, was formed after 480 min mechanical alloying. Densities of these sintered materials were ranged from 74 to 84%. Densification degree was due to the formation of composite powders. As the mechanical alloying time increased, the hardness was increased and tungsten particle size was decreased. Arc loss of the forged specimens was decreased as increasing the mechanical alloying time.