• Journal of environmental and Sanitary engineering
• /
• v.14 no.2
• /
• pp.113-119
• /
• 1999

In this study, the incineration of MEK and toluene was studied on a Pt supported alumina catalyst at temperature range from 200 to $350^{\circ}C$. An approach based on the Mars-van Krevelen rate model was used to explain the results. The object of this study was to study the kinetic behavior of the platinum catalyst for deep oxidation. The conversions of MEK and toluene were increased as the inlet concentration was decreased and the reaction temperature was increased. The maximum deep conversion of MEK and toluene were 91.81% and 55.69% at $350^{\circ}C$, respectively. The ${\kappa}_3$ constant increases with temperature faster than the ${\kappa}_1$ constant, that is, the surface concentration of ($VOCs{\cdots}O$) is higher than that of (O) at higher temperature according to the Mars-van Krevelen mechanism. Also the activation energy of toluene was larger than MEK for toluene is aromatic compound which have stronger bonding energy.Therefore, the catalytic incineration kinetics of MEK and toluene with Mars-van Krevelen mechanism could be used as the basic data for industrial processes.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.8
• /
• pp.706-710
• /
• 2008

The substrate bias effect on the current level of SOI-MOSFETs for high temperature operation has been investigated. In this work, we demonstrate the current level of SOI-MOSFETs can be controlled at different temperatures by applying a control bias to the substrate, showing that all current levels below T=150$^{\circ}C$ can be adjusted to a constant current level. 2D numerical simulation results show that substrate bias effectively controls the current conduction; as the substrate bias effectively lower the potential of the channel, inversion carrier generation is effectively controlled and consequently a constant current conduction level is achieved up to T=150$^{\circ}C$. We also demonstrate that the device simulated in this work has same operation at any temperature below T=150$^{\circ}C$ through mixed mode simulation.

• Journal of the Korean Home Economics Association
• /
• v.27 no.3
• /
• pp.29-38
• /
• 1989

The purpose of this study is to investigate the physiological respones and subjective wearing sensations of the body of different materials of underwears. Experimental underwears were round neck-line shirts made of 100% cotton (60's plain stitch), 100% untreated nylon and hydrophillic finished 100% nylon (140 D. tricot). Four healthy female served as subjects. The experimental chamber was controlled at a constant temperature (23±1℃), constant relative humidity (53±3%) and air velocity of 0.25m/sec. The skin temperature, rectal temperature, pulse rate, clothing climate of temperature and humidity, and subjective wearing sensations were measured every five minutes during 75min. The results showed the level of the fiber hygroscopic properties was most relevant in the sensations of wearing: thus, cotton and treated nylon were felt by the subjects as more confortable fabrics, than untreated nylon.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1567-1571
• /
• 1994

Under the assumption that thermal conductivity of the fin is constant and the conditions ate steady state, effects of non-constant and thermally asymmetric root temperature and unequal surrounding convection coefficients of the fin on the heat loss from a fin of rectangular profile are investigated. The heat loss form a rectangular fin becomes maximum when the highest root temperature deviates from the fin center to the fin side which has a higher convection coefficient as surrounding convection coefficients of the fin increase and as the difference between the convection coefficient of fin top side and that of fin bottom side increases.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.3
• /
• pp.48-55
• /
• 2003

This study investigates the effect of temperature and electric field strength on the Bingham characteristics of Electro-Rheological(ER) fluids which change their Yield shear stress and viscosity by temperature and electric field strength. It is found that under constant temperature the Yield sheal stress and viscosity of ER fluids proportionally increase with the applied electric field strength, and under constant applied electric field strength the Yield shear stress and viscosity of ER fluids decrease with the increasing temperature. These results are considered to be applied to the fluid and pneumatic power industry.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.5
• /
• pp.7-11
• /
• 2007

Kraft pulping of Trema orientalis (Nalita) was studied in order to find kinetic data for delignification. Pulping runs were carried out in the temperature range of $160-180\;^{\circ}C$ under constant and well-defined conditions. The delignification was found to be first order with respect to residual lignin and was chemically controlled. The rate of delignification reaction was increased 1.11-1.23 for $10\;^{\circ}C$ temperature increase in the range of $160-180\;^{\circ}C$ range. A mean value of 93% of lignin was removed at the transition between bulk and residual delignification. The influence of cooking temperature on the rate constant was expressed by an Arrhenius-type equation. The obtained activation energy of the delignification reaction was 6,164 cal/mol. The transition point between bulk and residual phase was shifted to lower lignin and carbohydrate yield with the increase of temperature.

• Journal of computational fluids engineering
• /
• v.4 no.2
• /
• pp.9-16
• /
• 1999

The present study investigates flow character and heat transfer behaviors of viscoelastic non-Newtonian fluid in a 2:1 rectangular duct. An axially-constant heat flux on bottom wall and peripherally constant temperature boundary condition(H1) was adopted. The Reiner-Rivlin fluid model is used as the normal stress model for the viscoelastic fluid and temperature-dependent viscosity model is adopted. The present results show a signifiant change of the main flow field which causes a large heat transfer enhancement. This phenomena can be explained by the combined effect of buoyancy, temperature-dependent viscosity and viscoelastic property on the flow.

• Journal of Powder Materials
• /
• v.13 no.6 s.59
• /
• pp.455-461
• /
• 2006

High temperature dielectric constants of the various ceramic materials have been measured using cavity perturbation method. The measurements were applied to refractory, traditional and fine ceramic powder compacts from room temperature to $1200^{\circ}C$. Calibration constant in the equation suggested by Hutcheon et al., was determined from the dielectric constants of reference specimen (teflon and alumina) at room temperature. From these results, informations on the refectory materials were obtained for the microwave kiln design and understanding of the microwave heating effects of ceramics have been improved.

• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.198-205
• /
• 1991

Sintered thermistor body was fabricated by solid reaction method using $Fe_2O_3, \;Al_2O_3, \;TiO_2$ and Si powder. Surface matrix of sintered body was investigated by SEM and $\beta$-constant was obtained from measurement of resistance variation in liquid bath. The values of thermistor constant $\beta$ of samples in the temperature range $-50~+50^{\circ}C$ were distributed from 927 to 4005k. This thermistor body can be used as temperature sensor for radiosonde.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.5
• /
• pp.413-417
• /
• 2003

The effect of 0-0.7 ㏖% addition of $Cr_2$$O_3$on the dielectric, pyroelectric, and piezoelectric properties were studied in the (Mg$0.7Pb_{1}$$3/Nb_{2}$3/)$O_3$-$0.3PbTiO_3$(0.7PMN-0.3PT) ceramics with composition near the morphotropic phase boundary. The dielectric constant and loss of the ceramics samples were measured as a function of temperature at various frequencies (0.1-100 KHz). The pyroelectric coefficient was measured by using the Byer-Roundy method as a function of temperature. Dielectric, pyroelectric, and piezoelectric constant achieved the maximum values of 0.4 ㏖% $Cr_2$$O_3$The transition temperature is continuously shifted to lower temperature with an increase of a small amount of $Cr_2$$O_3$.