• 한국도로학회논문집
• /
• 제18권1호
• /
• pp.13-21
• /
• 2016

PURPOSES : In this study, we analyzed the compressive strength characteristics of lean base concrete in relation to changes in the outdoor temperature after analyzing the cold and hot weather temperature standards and calculated the minimum and maximum temperatures when pouring concrete. We examined the rate of strength development of lean base concrete in relation to the temperature change and derived an appropriate analysis formula for FRC base structures by assigning the accumulated strength data and existing maturity formula. METHODS : We measured the strength changes at three curing temperatures (5, 20, and $35^{\circ}C$) by curing the concrete in a temperature range that covered the lowest temperature of the cold period, $5^{\circ}C$, to the highest temperature of the hot period, $35^{\circ}C$. We assigned the general lean concrete and FRC as test variables. A strength test was planned to measure the strength after 3, 5, 7, 14, and 28 days. RESULTS : According to the results of compressive strength tests of plain concrete and FRC in relation to curing temperature, the plain concrete had a compressive strength greater than 5 MPa at all curing temperatures on day 5 and satisfied the lean concrete standard. In the case of FRC, because the initial strength was substantially reduced as a result of a 30% substitution of fly ash, it did not satisfy the strength standard of 5 MPa when it was cured at $5^{\circ}C$ on day 7. In addition, because the fly ash in the FRC caused a Pozzolanic reaction with the progress into late age, the amount of strength development increased. In the case of a curing temperature of $20^{\circ}C$, the FRC strength was about 66% on day 3 compared with the plain concrete, but it is increased to about 77% on day 28. In the case of a curing temperature of $35^{\circ}C$, the FRC strength development rate was about 63% on day 3 compared with the plain concrete, but it increased to about 88% on day 28. CONCLUSIONS : We derived a strength analysis formula using the maturity temperatures with all the strength data and presented the point in time when it reached the base concrete standard, which was 5 MPa for each air temperature. We believe that our findings could be utilized as a reference in the construction of base concrete for a site during a cold or hot weather period.

• 콘크리트학회지
• /
• 제9권1호
• /
• pp.105-113
• /
• 1997

콘크리트 실린더 공시체의 크기에 따른 압축강도의 감소현상은 많은 관심을 받아 왔으나, 지금까지도 이에 대해 제시된 모델식이 없는 실정이다. 기존의 연구결과에 의하면 콘크리트의 강도는 부재의 크기가 증가할수록 감소하며 그 파괴거동을 규명하기 위해서는 비선형 파기역학 이론을 적용해야 함을 알 수 있다. 이전의 연구에서 표준형 콘크리트 실린더 공시체의 크기에 따른 압축강도의 변화를 파괴역학 이론에 따라 연구하고 실용적인 예측 모델식을 제시한 바 있다. 이 논문에서는 높이/직경의 비가 2/1이 아닌 비표준형 실린더 공시체를 고려하여 보다 일반적인 실린더 압축강도 에측 모델식을 제시하고자 한다. 이를 위하여 최대골재크기가 미소균열영역에 미치는 영향을 이론적으로 고찰하였으며, 특성길이의 개념을 새로이 도입하여 일반화된 크기효과에 대한 모델식을 제시하였다. 이 연구의 결과는 기존 구조물에서 채취한 다양한 크기의 콘크리트 코아 강도 등을 예측하는데도 매우 실용적으로 사용될 수 있을 것이다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회 논문집(II)
• /
• pp.1057-1062
• /
• 2000

The purpose of this study is to practice the method which can estimate 28-days strength of concrete in advance. This method is made for reliant quality control. Based on existing experiment, concrete that flyash added and normal concrete are placed into wall structure, and it is examined the difference between experiment use concrete and field use concrete. The result of this study are as follows : 1) Core test specimen have 10% lower strength to standard curing specimen. 2) At 28-days accelerated strength by microwave, average 35% in normal concrete, average 23% in flyash added concrete. 3) At coefficient of determination between compressive strength and accelerated strength, 0.84 in normal concrete core, 0.86 in standard curing normal concrete, 0.86 in flyash added concrete, 0.90 in standard curing flyash added concrete.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.453-458
• /
• 2001

This study was performed to reuse the dyeing wastewater sludge treated by Fenton process through the solidification/stabilization technique. To solidify the dyeing sludge the industrial by-products such as blast furnace slag, fly ash and waste sand with cement were used. The laboratory scale and pilot scale test were conducted at room temperature to make construction brick which has high compressive strength and low leaching of heavy metals. The experimental results showed that blast furnace slag and fly ash could be used instead of cement and the products satisfied the regulation of Korean Standards. The blast furnace slag increased the compressive strength and the optimum ratio of slag/dyeing sludge on dry basis was found 0.4. The solidifying agent of SB series could increase rapidly the compressive strength and the optimum ratio of solidifying agent/sludge on dry basis was 0.26 at which the strength was two times compared with non-added condition. The portion of waste and industrial by-products in matrix was over 80%. From the pilot test the optimum pressure in molding was 100kg/$\textrm{cm}^2$ at which the compressive strength was over 100kg/$\textrm{cm}^2$. And the strength increased continuously to 160kg/$\textrm{cm}^2$ until 120 days curing time due to pozzolanic reaction. When SB-20 as a solidifying agent was used, the unconfined compressive strength of dyeing sludge could be obtained 110kg/$\textrm{cm}^2$ which satisfied the regulation of cement brick in Korea Standard(KS).

• 한국추진공학회지
• /
• 제20권5호
• /
• pp.70-76
• /
• 2016

본 연구에서는 하이브리드 가스 발생기용 파라핀/알루미늄 왁스 연료의 기계적 특성 파악을 위한 인장 및 압축강도 실험을 수행하였다. 혼합된 알루미늄 입자의 크기와 첨가량에 따른 기계적 특성을 파악하기 위해 10 wt%, 20 wt%, 30 wt%의 나노 입자 첨가 시편과 5 wt%, 10 wt%, 15 wt%의 마이크로 입자 첨가 시편을 사용하였다. 평균입도 100 nm 및 $8{\mu}m$ 크기의 알루미늄 입자와 Sasol사의 미정질 파라핀 왁스(Sasol 0907)를 이용하였고, 인장시험과 압축 시험에 사용된 시편은 각각 ASTM-D638, ASTM D575-91 규격에 따라 제작하였다. 나노 입자의 첨가는 시편의 인장 및 압축강도를 크게 향상시키나 마이크로 입자의 첨가는 상대적으로 인장 및 압축강도의 증가에 미치는 영향이 미미한 것으로 파악되었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문 발표회
• /
• pp.23-26
• /
• 2003

This study is intended to investigate the properties of early strength development by application of TEA to the field. According to the results, when TEA is added, fluidity is almost same to base concrete, and increases upto aimed slump after field flowing. Setting time does not differ in the case of base and TEA, but retarded after flowing. The time when compressive strength gains 5 MPa, which side form can be removed, is 23 hours, and so the removal time is shortened by I hours in comparison with plain concrete. But compressive strength is almost same to that of plain concrete at 28 days. The rebound value of P type schmidt hammer show similar tendency to compressive strength, and the rebound value of structure is higher than that of standard curing specimen due to heat capacity effect and drying by the air outside. Therefore, it is thought that if the rebound value of P type schmidt hammer is controled. by about 26 in consideration of open air environment, it is very effective to determine the removal time of side forms.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2003년도 학술.기술논문발표회
• /
• pp.23.1-26
• /
• 2003

This study is intended to investigate the properties of early strength development by application of TEA to the field. According to the results, when TEA is added, fluidity is almost same to base concrete, and increases upto aimed slump after field flowing. Setting time does not differ in the case of base and TEA, but is retarded after flowing. The time when compressive strength gains 5 MPa, which side form can be removed, is 23 hours, and so the removal time is shortened by 1hours in comparison with plain concrete. But compressive strength is almost same to that of plain concrete at 28 days. The rebound value of P type schmidt hammer show similar tendency to compressive strength, and the rebound value of structure is higher than that of standard curing specimen due to heat capacity effect and drying by the air outside. Therefore, it is thought that if the rebound value of P type schmidt hammer is controled. by about 26 in consideration of open air environment, it is very effective to determine the removal time of side forms.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권6호
• /
• pp.103-111
• /
• 2015

콘크리트의 강도를 평가하기 위하여 반발경도법과 초음파속도법이 폭넓게 사용되고 있다. 그러나 재료의 상태뿐만 아니라 콘크리트의 재령, 성숙도 및 손상도 등에 따라 예측강도와 현장의 실제강도가 차이가 발생하게 된다. 표준공시체와 현장에서 드릴링에 의하여 채취하는 코어공시체의 압축강도는 드릴링하는 동안 기계에 의한 교란이 발생하여 압축강도에 영향을 미치게 된다. 또한 반발경도 및 초음파속도의 경우에도 콘크리트의 재령 및 성숙도가 변화함에 따라 표면의 경도와 내부 미세조직의 변화에 의해서도 변화하게 된다. 저자들은 재령와 코어의 영향을 비파과시험결과에 반영하기 위하여 실험을 실시하였으며, 코어 및 콘크리트 재령에 의한 영향을 압축강도 실험 및 예측결과와 비교분석하였다.

• Advances in concrete construction
• /
• 제1권4호
• /
• pp.305-318
• /
• 2013

Engineering properties such as compressive strength, splitting tensile strength, modulus of rupture, modulus of elasticity and Poisson's ratio of geopolymer concrete (GPC) and steel fibre reinforced geopolymer concrete (SFRGPC) have been obtained from standard tests and compared. A total of 15 specimens were tested for determining each property. The grade of concrete used was M 40. The percentages of steel fibres considered include 0.25%, 0.5%, 0.75% and 1%. In general, the addition of fibres improved the mechanical properties of both GPC and SFRGPC. However the increase was found to be nominal in the case of compressive strength (8.51%), significant in the case of splitting tensile strength (61.63%), modulus of rupture (24%), modulus of elasticity (64.92%) and Poisson's ratio (50%) at 1% volume fraction of fibres. An attempt was made to obtain the relation between the various engineering properties with the percentage of fibres added.

• 한국지반공학회논문집
• /
• 제29권1호
• /
• pp.39-47
• /
• 2013

석탄회를 활용한 CLSM(Controlled Low Strength Material)의 적용성이 증가됨에 따라, 본 연구에서는 경량기포CLSM의 압축강도와 단위중량과의 관계에 초점을 맞추어, CLSM 재료에 관련된 기초연구를 수행하였다. 일축압축강도는 구조물에 적용시 재굴착이 가능한지를 판단할 수 있는 기준이 되고 있으며 시험결과를 통해 경제성 및 효율성, 굴착성 등을 판단할 수 있는 중요한 배합설계변수이다. 그러나 CLSM의 일축압축강도는 재령 28일 기준으로 적용성을 판단하기 때문에, 정량적인 일축압축강도값을 알기 위해서는 배합 후 일정시간이 지나야한다. 본 연구에서는 저강도 고유동화재(CLSM)에 기포를 혼입하여 경량화시킨 경량기포 CLSM에 중점을 두어 경량기포 CLSM의 압축강도와 단위중량(기포슬러리 단위중량, 겉보기 단위중량)과의 관계를 분석하였고, 슬러리를 28일까지 양생시키지 않고 단위중량만으로 28일의 압축강도를 쉽게 예측할 수 있는 관계식을 제안하였다.