• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.4
• /
• pp.414-420
• /
• 1985

The melting phenomenal of the horizontal cylindrical ice-bar submerged in water are experimentally investigated for the temperature range from 2.5.deg. C to 15.deg. C. The shapes of the melting ice-bar are recorded by the Photo-elasticity Apparatus with modification of the test section. The shadowgraphs of the melting ice-bar show that water adjacent to the bar flows upward for the temperature range from 2.5.deg. C to 5.6.deg. C while above the temperature of 5.6.deg. C the flow is downward direction. The local and average Nusselt numbers become minimum at 5.6.deg. C which is considered as a critical temperature and the Nusselt numbers increase as temperature difference from the critical temperature increase.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.247-250
• /
• 2012

This paper describes a DC-DC Boost converter for Thermoelectric Energy Harvesting. The designed converter boosts the $V_{DD}$ through a start-up block from a low output voltage of thermoelectric devices and the boosted $V_{DD}$ is used to operate the internal block circuits. When $V_{DD}$ reaches a predefined value, a detector circuit makes the start-up block turn off for minimizing current consumption. The final boosted $V_{OUT}$ is achieved by alternately operating the DC-DC converter for $V_{DD}$ and the other converter for final output $V_{OUT}$ according to the comparator output. Simulation results shows that the designed converter outputs 2.8V from an input voltage of 200mV. The area of the chip designed using a 0.35um CMOS process is $1.52mm{\times}0.95mm$ including pads.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.1
• /
• pp.63-70
• /
• 2015

In this paper, a receiver has been developed in a $0.11-{\mu}m$ CMOS technology for 900 MHz RFID communication system applications. The receiver is composed of an envelope detector, a low-pass-filter, a comparator, D flip-flops, as well as an oscillator to provide the clock for digital blocks. The receiver is designed for low power consumption, which would be suitable for passive RFID tags. In this circuit, a digital data slicer was employed instead of the conventional analog data slicer in order to reduce the power consumption. The clock frequency is 1.68 MHz and the circuit operates with a power consumption as small as $5{\mu}W$. The chip size is $325{\mu}m{\times}290{\mu}m$ excluding the probing pads.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.2
• /
• pp.161-165
• /
• 2012

It is one of the most important to protect the battery over charging for stable use and to extend the life of battery which occurs with repeated charging and discharging. Various research have been studied to know the state of health, and in this paper the terminal voltage of battery is measured to calculate the state of charge simply. The circuit used comparator is designed and built not to fall under the specific voltage of battery. The designed circuit board is attached to the automatic water sanitizer device with a solar power system. The system is located in the water tank where there is not water and electric service, and confirmed that the state of working is good.

• The Journal of Korean Medicine
• /
• v.38 no.3
• /
• pp.124-142
• /
• 2017

Objectives: This study aimed to learn what should be considered in [Guideline of Clinical Trial with Herbal Medicinal Product for Gastric Cancer)] by analyzing the existing guidelines and clinical trials. Methods: The development committee searched guidelines for herbal medicinal product or gastric cancer developed already. Then, clinical trials for gastric cancer using herbal medicine were searched. The searched trials were analyzed in terms of inclusion and exclusion of participants, intervention, comparator, outcomes and trial design. Then, we compared the results of analysis with the regulations and guidelines of Ministry of Food and Drug Safety to suggest the issue that we will have to consider when making the [Guideline of Clinical Trial with Herbal Medicinal Product for Gastric Cancer]. Results: As a result, few guidelines for anti-tumor agent and clinical trial with herbal medicinal product were searched in the national institution homepage. In addition, 10 articles were searched by using the combination following search term; 'stomach neoplasm', 'herbal medicine', 'Medicine, Korean traditional', 'Medicine, Chinese Traditional', 'TCM', 'TKM', 'trial'. Most trials included gastric cancer participants with medical history of operation. The type of intervention was various such as decoction, granules, and fluid of intravenous injection. Comparators were diverse such as placebo, conventional treatment including chemotherapy and nutritional supplement. The most frequently used outcome for efficacy was quality of life. Besides, the symptom score, tumor response, and survival rate were used. Safety was investigated by recording adverse events. Conclusion: We found out some issue by reviewing the existing guidelines and comparing it with clinical trials for gastric cancer and herbal medicinal products. These results will be utilized for developing [Guideline of Clinical Trial with Herbal Medicinal Product for Gastric Cancer].

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.7
• /
• pp.493-502
• /
• 2001

This paper propose a new built-in current sensor(BICS) for current testing that has some advantages compared with conventional logic testing. The designed BICS detects the fault in circuit under test (CUT) and makes a Pass/Fail signal by comparison between CUT current and duplicated inverter current. The proposed circuit consists of a differential amplifier, a comparator and a inverter. It requires 10 MOSFETs and 3 inverters. Since the designed BICS do not require the extra clock, the added extra pin is only one output pin. The mode selection is not used in this circuit. Therefore we can apply the circuit to on-line testing. The validity and effectiveness are verified through the HSPICE simulation of circuits with defects. When CUT is a 8$\times$8 parallel multiplier, area overhead of the BICS is about 4.34%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.37-44
• /
• 2011

This paper presents the method of improving the data rate and BER in the inductive coupling link using a BPM signaling method. A complementary switching transmitter is used to remove invalid glitches at transmitted data, and the concept of pre-distortion is introduced to optimize received data. Also, an integrating receiver is used to increase the sampling margin and equalizing transistors are added in the pre-charge path of the integrator and comparator for high frequency operation. The transceiver designed with a 0.13 um CMOS technology operates at 2.4 Gb/s and consumes 5.99 mW from 1.2 V power supply.

• Publications of The Korean Astronomical Society
• /
• v.22 no.4
• /
• pp.189-199
• /
• 2007

In this paper, we describe the proposed KVN (Korean VLBI Network) clock system in order to make the observation of the VLBI effectively. In general, the GPS system is widely used for the time information in the single dish observation. In the case of VLBI observation, a very high precise frequency standard is needed to perform the observation in accordance with the observation frequency using the radio telescope with over 100km distance. The objective of the high precise clock system is to insert the time-tagging information to the observed data and to synchronize it with the same clock in overall equipments which used in station. The AHM (Active Hydrogen Maser) and clock system are basically used as a frequency standard equipments at VLBI station. This system is also adopted in KVN. The proposed KVN clock system at each station consists of the AHM, GPS time comparator, standard clock system, time distributor, and frequency standard distributor. The basic experiments were performed to check the AHM system specification and to verify the effectiveness of implemented KVN clock system. In this paper, we briefly introduce the KVN clock system configuration and experimental results.

• Journal of IKEEE
• /
• v.9 no.1 s.16
• /
• pp.57-64
• /
• 2005

This paper presents a built-in current sensor(BICS) that detects defects in CMOS integrated circuits using the current testing technique. This circuit employs a cross-coupled connected PMOS transistors, it is used as a current comparator. The proposed circuit has a negligible impact on the performance of the circuit under test (CUT) and high speed detection time. In addition, in the operation of the normal mode, the BlCS does not have dissipation of extra power, and it can be applied to the deep submicron process. The validity and effectiveness are verified through the HSPICE simulation on circuits with defects. The area overhead of a BlCS versus the entire chip is about 9.2%. The chip was fabricated with Hynix $0.35{\mu}m$ 2-poly 4-metal N-well CMOS standard technology.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.13-17
• /
• 2013

In lighting system where several large-area organic light-emitting diode (OLED) lighting panels are involved, panel aging may appear differently from each other, resulting in a falling-off in lighting quality. To achieve uniform light output across large-area OLED lighting panels, we have employed an optical feedback circuit. Light output from each OLED panel is monitored by the optical feedback circuit that consists of a photodiode, I-V converter, 10-bit analogdigital converter (ADC), and comparator. A photodiode generates current by detecting OLED light from one side of the glass substrate (i.e., edge emission). Namely, the target luminance from the emission area (bottom emission) of OLED panels is monitored by current generated from the photodiode mounted on a glass edge. To this end, we need to establish a mapping table between the ADC value and the luminance of bottom emission. The reference ADC value corresponds to the target luminance of OLED panels. If the ADC value is lower or higher than the reference one (i.e., when the luminance of OLED panel is lower or higher than its target luminance), a micro controller unit (MCU) adjusts the pulse width modulation (PWM) used for the control of the power supplied to OLED panels in such a way that the ADC value obtained from optical feedback is the same as the reference one. As such, the target luminance of each individual OLED panel is unchanged. With the optical feedback circuit included in the lighting system, we have observed only 2% difference in relative intensity of neighboring OLED panels.