• Steel and Composite Structures
• /
• 제31권5호
• /
• pp.503-516
• /
• 2019

This work presents a dynamic investigation of functionally graded (FG) plates resting on elastic foundation using a simple quasi-3D higher shear deformation theory (quasi-3D HSDT) in which the stretching effect is considered. The culmination of this theory is that in addition to taking into account the effect of thickness extension (${\varepsilon}_z{\neq}0$), the kinematic is defined with only 4 unknowns, which is even lower than the first order shear deformation theory (FSDT). The elastic foundation is included in the formulation using the Pasternak mathematical model. The governing equations are deduced through the Hamilton's principle. These equations are then solved via closed-type solutions of the Navier type. The fundamental frequencies are predicted by solving the eigenvalue problem. The degree of accuracy of present solutions can be shown by comparing it to the 3D solution and other closed-form solutions available in the literature.

• Journal of Adhesion and Interface
• /
• 제20권1호
• /
• pp.1-8
• /
• 2019

Fabrication of monolayer is important method for enhancing physical and chemical characteristics such as light shielding and antireflection while maintaining thin film properties. In previous studies, monolayers were fabricated by various methods on small substrates, but processes were complicated and difficult to form monolayers with large area. We used rod coating equipment with a small amount of coating liquid to form a HCP (hexagonal closed packing) coating of PMMA beads on PET(poly(ethylene terephthalate)) substrate with $20cm{\times}20cm$ size. We observed that changes in morphologies of monolayers by using the solvents with different boiling points and vapor pressures, by adapting surfactants on particles and by applying plasma treatment on substrates. The coverage was increased by 20% by optimizing the coating conditions including meniscus of beads, control of the attraction - repulsion forces and surface energy. This result can potentially be applied to optical films and sensors because it is possible to make a uniform and large-scale monolayer in a simple and rapid manner when it is compared to the methods in previous studies.

• Geomechanics and Engineering
• /
• 제22권6호
• /
• pp.509-518
• /
• 2020

Multi-layered primary linings have been proved to be highly effective for tunneling in severe squeezing grounds. But there still has not existed well-established design method for it. Basically, there are two main critical problems in this method, including determinations of allowable deformation and distribution of support stiffness. In order to address such problems, an attempt to investigate the mechanical response of a circular tunnel with double primary linings is performed in this paper. Analytical solutions in closed form for stresses and displacements around tunnels are derived. In addition, the effectiveness and reliability of theoretical formulas provided are well validated by using the numerical method. Finally, based on the analytical solutions, a parametric investigation on the effects of allowable deformation and distribution of support stiffness on tunnel performance is conducted. Results show that the rock pressure and displacement are significantly affected by these two design parameters. It can be found that rock pressure decreases as either allowable deformation increases or stiffness of the first primary lining decreases, but rock displacement shows an opposite trend. This paper can provide a useful guidance for the design of multi-layered primary linings.

• Coupled systems mechanics
• /
• 제11권2호
• /
• pp.151-166
• /
• 2022

Peltier cells have low efficiency, but they are becoming attractive alternatives for affordable and environmentally clean cooling. In this line, the current article develops closed-form and semianalytical solutions to improve the temperature distribution of Bi₂Te₃ thermoelements. From the distribution, the main objective of the current work-the optimal electric intensity to maximize cooling-is inferred. The general one-dimensional differential coupled equation is integrated for linear and quadratic geometry of thermoelements, under temperature constant properties. For a general shape, a piece-wise solution based on heat flux continuity among virtual layers gives accurate analytical solutions. For variable properties, another piece-wise solution is developed but solved iteratively. Taking advantage of the formulae, the optimal intensity is directly derived with a minimal computational cost; its value will be of utility for more advanced designs. Finally, a parametric study including straight, two linear, barrel, hourglass and vase geometries is presented, drawing conclusions on how the shape of the thermoelement affects the coupled phenomena. A specially developed coupled and non-linear finite element research code is run taking into account all the materials of the cell and using symmetries and repetitions. These accurate results are used to validate the analytical ones.

• International Journal of Control, Automation, and Systems
• /
• 제5권5호
• /
• pp.547-558
• /
• 2007

This paper proposes a simpler solution to the stabilization problem of a special class of nonlinear underactuated mechanical systems which includes widely studied benchmark systems like Inertia Wheel Pendulum, TORA and Acrobot. Complex internal dynamics and lack of exact feedback linearizibility of these systems makes design of control law a challenging task. Stabilization of these systems has been achieved using Energy Shaping and damping injection and Backstepping technique. Former results in hybrid or switching architectures that make stability analysis complicated whereas use of backstepping some times requires closed form explicit solutions of highly nonlinear equations resulting from partial feedback linearization. It also exhibits the phenomenon of explosions of terms resulting in a highly complicated control law. Exploiting recently introduced Dynamic Surface Control technique and using control Lyapunov function method, a novel nonlinear controller design is presented as a solution to these problems. The stability of the closed loop system is analyzed by exploiting its two-time scale nature and applying concepts from Singular Perturbation Theory. The design procedure is shown to be simpler and more intuitive than existing designs. Design has been applied to important benchmark systems belonging to the class demonstrating controller design simplicity. Advantages over conventional Energy Shaping and Backstepping controllers are analyzed theoretically and performance is verified using numerical simulations.

• Geomechanics and Engineering
• /
• 제14권3호
• /
• pp.233-240
• /
• 2018

Pullout tests are usually employed to determine the ultimate bearing capacity of reinforced soil, and the load-displacement curve can be obtained easily. This paper presents an analytical solution for predicting the full-range mechanical behavior of a buried planar reinforcement subjected to pullout based on a bi-linear bond-slip model. The full-range behavior consists of three consecutive stages: elastic stage, elastic-plastic stage and debonding stage. For each stage, closed-form solutions for the load-displacement relationship, the interfacial slip distribution, the interfacial shear stress distribution and the axial stress distribution along the planar reinforcement were derived. The ultimate load and the effective bond length were also obtained. Then the analytical model was calibrated and validated against three pullout experimental tests. The predicted load-displacement curves as well as the internal displacement distribution are in closed agreement with test results. Moreover, a parametric study on the effect of anchorage length, reinforcement axial stiffness, interfacial shear stiffness and interfacial shear strength is also presented, providing insights into the pullout behaviour of planar reinforcements of MSE structures.

• International Journal of Highway Engineering
• /
• 제17권4호
• /
• pp.25-31
• /
• 2015

PURPOSES: Implementation and verification of the simple linear cohesive viscoelastic contact model that can be used to simulate dynamic behavior of sticky aggregates. METHODS: The differential equations were derived and the initial conditions were determined to simulate a free falling ball with a sticky surface from a ground. To describe this behavior, a combination of linear contact model and a cohesive contact model was used. The general solution for the differential equation was used to verify the implemented linear cohesive viscoelastic API model in the DEM. Sensitivity analysis was also performed using the derived analytical solutions for several combinations of damping coefficients and cohesive coefficients. RESULTS : The numerical solution obtained using the DEM showed good agreement with the analytical solution for two extreme conditions. It was observed that the linear cohesive model can be successfully implemented with a linear spring in the DEM API for dynamic analysis of the aggregates. CONCLUSIONS: It can be concluded that the derived closed form solutions are applicable for the analysis of the rebounding behavior of sticky particles, and for verification of the implemented API model in the DEM. The assumption of underdamped condition for the viscous behavior of the particles seems to be reasonable. Several factors have to be additionally identified in order to develop an enhanced contact model for an asphalt mixture.

• Computers and Concrete
• /
• 제18권5호
• /
• pp.983-998
• /
• 2016

Structural optimization is one of the most important topics in structural engineering and has a wide range of applicability. Therefore, the main objective of the present study is to apply the Lagrange Multiplier Method (LMM) for minimum cost design of singly and doubly reinforced rectangular concrete beams. Concrete and steel material costs are used as objective cost function to be minimized in this study, and ultimate flexural strength of the beam is considered to be as the main constraint. The ultimate limit state method with partial material strength factors and equivalent concrete stress block is used to derive general relations for flexural strength of RC beam and empirical coefficients are taken from topic 9 of the Iranian National Building Regulation (INBR9). Optimum designs are obtained by using the LMM and are presented in closed form solutions. Graphical representation of solutions are presented and it is shown that proposed design curves can be used for minimum cost design of the beams without prior knowledge of optimization and without the need for iterative trials. The applicability of the proposed relations and curves are demonstrated through two real life examples of SRB and DRB design situations and it is shown that the minimum cost design is actually reached using proposed method.

• Journal of Korean Society of Steel Construction
• /
• 제14권3호
• /
• pp.423-432
• /
• 2002

This study presented analytical and numerical solutions for spatial free vibration of nonsymmetric thin-walled circular curved beams. The closed-form solutions were obtained for in-plane free vibration analylsis of monosymmetric curved beams. Likewise, two types of thin-walled curved beam elements were developed using the third and the fifth order Hermitian polynomials. In order to illustrate the accuracy and usefulness of the present method, this study presented analytical and numerical solution and compared these with the results using the ABAQUS's shell elements. In particular, effects of the thickness-curvature as well as the inextensional condition were investigated on the free vibration of curved beams with nonsymmetric sections.

• Journal of The Korean Astronomical Society
• /
• 제53권5호
• /
• pp.99-102
• /
• 2020

I show that when the observables (π_E, t_E, θ_E, π_s, µ_s) are well measured up to a discrete degeneracy in the microlensing parallax vector π_E, the relative likelihood of the different solutions can be written in closed form P_i = KH_iB_i, where H_i is the number of stars (potential lenses) having the mass and kinematics of the inferred parameters of solution i and B_i is an additional factor that is formally derived from the Jacobian of the transformation from Galactic to microlensing parameters. Here t_E is the Einstein timescale, θ_E is the angular Einstein radius, and (π_s, µ_s) are the (parallax, proper motion) of the microlensed source. The Jacobian term B_i constitutes an explicit evaluation of the "Rich Argument", i.e., that there is an extra geometric factor disfavoring large-parallax solutions in addition to the reduced frequency of lenses given by H_i. I also discuss how this analytic expression degrades in the presence of finite errors in the measured observables.