• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.911-913
• /
• 2013

In this paper, we present the sweeping machine with cyclone type dust collector for cleaning shipment exterior wall. Important cyclone characteristics such as the collection efficiency, pressure and velocity fields have been discussed and compared with the experimental data. The purpose of this study is to introduce the mechanism design of the high efficiency sweeping machine using the cyclone dust collector. Generally, the increase of inlet velocity of air in a cyclone dust collector improves the separation efficiency, while it results in increasing in the pressure losses nonlinearly.

• Analytical Science and Technology
• /
• v.6 no.5
• /
• pp.521-530
• /
• 1993

According to the Montreal Protocol, CFC 113, one of the ozone-depleting substances, will be prohibited to use as a cleaning solvent essentially in the electronic industry. Therefore, the development of the alternative cleaning solvents to CFC 113 is being accelerated. A number of the alternative cleaning solvents are avialable on the market. The alternatives of Axarel 32(DuPont), Cleanthru 750H(KAO Chemical), and EC-Ultra(Petroferm) are chosen for the comparison of cleaning performance with CFC 113. The test methods for measuring the cleaning performance were composed of the measurement of the physical properties, the experiments on the material compatibility with cleaning solvents, the measurement of the evaporation rate, and finally the experiments of the removal efficiency. Normally the basic physical properties of the alternatives had higher boiling points, viscosity and surface tension, which were quite different to those of CFC 113. In terms of solubility of rosin-based flux, the solubilities of abietic acid (nonpolar organic) were similar, but those of the activator (polar organic) in the alternatives were better than CFC 113. The evaporation of the alternatives was very slow, compared to CFC 113, which had much lower boiling point. All the cleaning solvents showed the good material compatibility with FR4 and Cu-coated PCB. The better removal efficiencies of abietic acid were obtained when using the ultrasonic mechanical energy over the dipping method. The experiments also indicated the very slow-eavaporating solvent was not desirable with the dipping cleaning method, and the differences in the removal efficiency of the alternatives with the ultrasonic cleaning method were negligible. Among the alternatives, the overall cleaning performances were obsorved as almost similar. Before selecting the ultimate cleaning solvent, the application of cleaning machine, environmental issues, and economics are simultaneously considered with the cleaning performance.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.4 no.1
• /
• pp.119-124
• /
• 2004

Real data as web log file tend to be incomplete. But we have to find useful knowledge from these for optimal decision. In web log data, many useful things which are hyperlink information and web usages of connected users may be found. The size of web data is too huge to use for effective knowledge discovery. To make matters worse, they are very sparse. We overcome this sparse problem using Markov Chain Monte Carlo method as multiple imputations. This missing value imputation changes spare web data to complete. Our study may be a useful tool for discovering knowledge from data set with sparseness. The more sparseness of data in increased, the better performance of MCMC imputation is good. We verified our work by experiments using UCI machine learning repository data.

• Journal of Korean Institute of Industrial Engineers
• /
• v.37 no.4
• /
• pp.415-420
• /
• 2011

Snow removal system is named for machinery which manages roads for passing of pedestrians and automobiles when snow is piled up on the road. This paper studies configuration design of snow removal system that has several functions-melting snow in the street without moving it to other place, transferring snow to the melter and cleaning road by spraying water for cleaning road. These sorts of functions are analyzed by function decomposition method of Kirshman and Fadel and, based upon which, machine parts are selected. Layout design would follow functional design to testify if the selected component satisfies space which is allowed by constraints.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.3
• /
• pp.403-410
• /
• 2020

Continuous industrial development has led to a better quality of life for everyone, even further accelerating industrial growth. Industrial development, however, has also caused environmental degradation, which is posing a serious threat to humanity. It has also encouraged the indiscriminate use of limited resources, causing resource depletion. Efficient resource management based on resource circulation is critical to saving resources. Resource circulation methods are as follows: reducing the use of resources in the manufacturing process, recycling used or reprocessed products and reusing used resources without being reprocessed, remanufacturing with end-of-life products with disassembled parts. Furthermore, remanufacturing process including cleaning, inspection, repairing, and reassembling facilitate performance level as well as new typical products. It is noteworthy that the remanufacturing of machine tools can significantly save resources because their structural parts are substantially large in size. Machine tools have served as a foundation for the manufacturing industry, which has driven Korea's industrial development. Nevertheless, a few research has been reported for remanufacturing technology with used machine tools. Relevant research of developing a remanufacturing process chart and method is prerequisite for saving the resource and environments.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.3
• /
• pp.47-52
• /
• 2017

Solar cell industry requires high technologies to stabilize apparatuses for the wafer manufacturing. Vibrations of squaring & grinding machines are one of the most critical factors for causing residual stresses of ingots, which are the main reasons of the breakage in the following processes such as wire sawing, cleaning, and modularity. In this study, the structure of a squaring & grinding machine has been analyzed through experiments and computer simulations to figure out the ways to suppress the vibrations effectively, and further to minimize the breakage of wafers. The result shows that simple design changes of applying a few ribs can improve the stability of the machine.

• Journal of Food Hygiene and Safety
• /
• v.25 no.4
• /
• pp.346-353
• /
• 2010

This study was conducted to determine cleaning effects of environmental-friendly washing detergent on milking installation in dairy farms. Milking machine, cooling machine and milking liner were washed by alkaline detergent and acid detergent for first three weeks and alkaline detergent and environmental~friendly detergent for next three weeks and the results get through microorganism and physico-chemistry analysis at the five district dairy farms different from environment. E-coli, coliform, fecal coliform, staphylococcus aureus, fecal streptococcus, prsudomonas aeruginosa and yersinia were not found in all of the dairy farms, and total colony counts were no difference compared with chemical detergent. The water for washing exceeded the determining acceptable level of nitrate nitrogen in the Anseong, Onyang and Cheonan and the remaining substance of washed water was also high levels. The cause of the result was that the level of nitrate nitrogen of water is basically high. Therefore, this study indicated that washing effect is no differences between environmental-friendly detergent and chemical detergent by washing for milking machine and cooling machine. Above all, producing high quality milk is to manage the water quality as well as using detergent.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.3
• /
• pp.233-240
• /
• 2014

PURPOSE. To evaluate the effects of different abutment geometries in combination with varying luting agents and the effectiveness of different cleaning methods (prior to re-cementation) regarding the retentiveness of zirconia copings on implants. MATERIALS AND METHODS. Implants were embedded in resin blocks. Three groups of titanium abutments (pre-fabricated, height: 7.5 mm, taper: $5.7^{\circ}$; customized-long, height: 6.79 mm, taper: $4.8^{\circ}$; customized-short, height: 4.31 mm, taper: $4.8^{\circ}$) were used for luting of CAD/CAM-fabricated zirconia copings with a semi-permanent (Telio CS) and a provisional cement (TempBond NE). Retention forces were evaluated using a universal testing machine. Furthermore, the influence of cleaning methods (manually, manually in combination with ultrasonic bath or sandblasting) prior to re-cementation with a provisional cement (TempBond NE) was investigated with the pre-fabricated titanium abutments (height: 7.5 mm, taper: $5.7^{\circ}$) and SEM-analysis of inner surfaces of the copings was performed. Significant differences were determined via two-way ANOVA. RESULTS. Significant interactions between abutment geometry and luting agent were observed. TempBond NE showed the highest level of retentiveness on customized-long abutments, but was negatively affected by other abutment geometries. In contrast, luting with Telio CS demonstrated consistent results irrespective of the varying abutment geometries. Manual cleaning in combination with an ultrasonic bath was the only cleaning method tested prior to re-cementation that revealed retentiveness levels not inferior to primary cementation. CONCLUSION. No superiority for one of the two cements could be demonstrated because their influences on retentive strength are also depending on abutment geometry. Only manual cleaning in combination with an ultrasonic bath offers retentiveness levels after re-cementation comparable to those of primary luting.

• The Journal of Advanced Prosthodontics
• /
• v.9 no.2
• /
• pp.110-117
• /
• 2017

PURPOSE. This laboratory study assessed the effect of different dentin cleaning procedures on shear bond strength of resin cements for recementing prosthesis. MATERIALS AND METHODS. A $4{\times}4$ flat surface was prepared on the labial surface of 52 maxillary central incisors. Metal frames ($4{\times}4{\times}1.5mm$) were cast with nickel-chromium alloy. All specimens were randomly divided into 2 groups to be cemented with either Panavia F2.0 (P) or RelyX Ultimate (U) cement. The initial shear bond strength was recorded by Universal Testing Machine at a crosshead speed of 0.5 mm/min. Debonded specimens were randomly allocated into 2 subgroups (n = 13) according to the dentin cleaning procedures for recementation. The residual cement on bonded dentin surfaces was eliminated with either pumice slurry (p) or tungsten carbide bur (c). The restorations were rebonded with the same cement and were subjected to shear test. Data failed the normality test (P < .05), thus were analyzed with Mann Whitney U-test, Wilcoxon signed rank test, and two-way ANOVA after logarithmic transformation (${\alpha}=.05$). RESULTS. The initial shear bond strength of group P was significantly higher than group U (P = .001). Pc and Uc groups presented higher bond strength after recementation compared to the initial bond strength. However, it was significant only in Pc group (P = .034). CONCLUSION. The specimens recemented with Panavia F2.0 provided higher bond strength than RelyX Ultimate cement. Moreover, a tungsten carbide bur was a more efficient method in removing the residual resin cement and increased the bond strength of Panavia F2.0 cement after recementation.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.27 no.2
• /
• pp.125-140
• /
• 2011

The remnant of temporary cement on the intaglio surface of cast restoration may have a negative effect on the retentive strength of permanent cement. This study was to evaluate the effect of temporary cement cleaning methods on the retentive strength of cementation type implant prostheses. Prefabricated implant abutments - height 5.5mm, diameter 4.5mm, 6 degree axial wall taper with chamfer margins were used. Forty copings-abutment specimens were divided into four groups(each n=10) according to the cleaning methods for temporary cement(Temp-$Bond^{(R)}$) as follows : no temporary cementation(the control group), orange solvent, ultrasonic cleaning, air borne-particle abrasion. After the application of temporary cement and the separation, the cleaning procedure was performed according to the protocol of each group. The specimens were cemented with $Premier^{(R)}$ Implant $Cement^{TM}$. After the permanent cementation, the specimens were subjected to thermocycling and pulled out from the specimens with a universal testing machine at a cross-head speed of 0.5mm/min. After the retentive strength test, all the specimens were cleaned using ultrasonic cleaning, abraded with air borne-particles, and steam-cleaned. Likewise, the specimens were temporarily cemented(Temp-$Bond^{(R)}$ NE), cleaned according to the protocol of each group, cemented with $Premier^{(R)}$ Implant $Cement^{TM}$ and subjected to thermocycling and measurement of their retentive strength. The mean of group with orange solvent were significantly lower than those of other groups(p<0.05). There was no significance between group with ultrasonic cleaning and group with air borne-particle abrasion. Group with ultrasonic cleaning and group with air-particle abrasion were no significance at control group. There was no significance between group cemented with Temp-$Bond^{(R)}$ and group cemented with Temp-$Bond^{(R)}$ NE. Within the limitation of this study, it can be concluded that the temporary cement cleaning method with only orange solvent may have a negative effect on the retentive strength of permanent cement. Ultrasonic cleaning and air borne-particle abrasion methods are recommended for the temporary cement cleaning method on cementation type implant prostheses.