• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1068-1071
• /
• 2001

Recently, the minimum line width shows a tendancy to decrease and the multi-level to increase in semiconductor. Therefore, a planarization technique is needed, which chemical polishing(CMP) is considered as one of the most important process. CMP accomplishes a high polishing performance and a global planarization of high quality. But there are several defects in CMP such as microscratches, abrasive contaminations, and non-uniformity of polished wafer edges. Spin Etching can improve the defects of CMP. It uses abrasive-free chemical solution instead of slurry. Wafer rotates and chemical solution is simultaneously dispensed on a whole surface of the wafer. Thereby chemical reaction is occurred on the surface of wafer, material is removed. On this study, TEOS film is removed by CMP and Spin Etching, the results are estimated at a viewpoint of material removal rate(MRR) and within wafer non-uniformity(WIWNU).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.140-143
• /
• 2003

BST thin films have a good thermal-chemical stability, insulating effect and variety of phases. However, BST thin films have problems of the aging effect and mismatch between the BST thin film and electrode. Also, due to the high defect density and surface roughness at grain boundarys and in the grains, which degrades the device performances. In order to overcome these weakness, we first applied the chemical mechanical polishing (CMP) process to the polishing of ferroelectric film in order to obtain a good planarity of electrode/ferroelectric film interface. BST ferroelectric film was fabricated by the sol-gel method. And then, we compared the structural characteristics before and after CMP process of BST films. We expect that our results will be useful promise of global planarization for FRAM application in the near future.

• 한국전기전자재료학회논문지
• /
• 제13권7호
• /
• pp.568-574
• /
• 2000

We have been optimized tungsten(W) plug CMP(chemical mechanical polishing) characteristics using two different kinds of component of slurry and two different kinds of pad which have different hardness. The comparison of oxide film roughness on around W plug after polishing has been carried out. And W plug recess for consumable sets and dishing effect at dense area according to the rate of over-polishing has been investigated. Also the analysis of residue on surface after cleaning have been performed. As a experimental result we have concluded that the consumable set of slurry A and hard pad was good for W plug CMP process. After decreasing the rate of chemical reaction of silica slurry and adding two step buffering we could reduce the expanding of W plug void however we are still recognizing to need a more development for those kinds of CMP consumables.

• Tribology and Lubricants
• /
• 제35권6호
• /
• pp.323-329
• /
• 2019

Sapphire is currently used as a substrate material for blue light-emitting diodes (LEDs). The market for sapphire substrates has expanded rapidly as the use of LEDs has extended into various industries. However, sapphire is classified as one of the most difficult materials to machine due to its hardness and brittleness. Recently, a lap-grinding process has been developed to combine the lapping and diamond mechanical polishing (DMP) steps in a single process. This paper studies, the effect of wafer surface roughness on the chemical mechanical polishing (CMP) process by pressure and abrasive concentration in the lap-grinding process of a sapphire wafer. In this experiment, the surface roughness of a sapphire wafer is measured after lap-grinding by varying the pressure and abrasive concentration of the slurry. CMP is carried out under pressure conditions of 4.27 psi, a plate rotation speed of 103 rpm, head rotation speed of 97 rpm, and slurry flow rate of 170 ml/min. The abrasive concentration of the CMP slurry was 20wt, implying that the higher the surface roughness after lapgrinding, the higher the material removal rate (MRR) in the CMP. This is likely due to the real contact area and actual contact pressure between the rough wafer and polishing pad during the CMP. In addition, wafers with low surface roughness after lap-grinding show lower surface roughness values in CMP processes than wafers with high surface roughness values; therefore, further research is needed to obtain sufficient surface roughness before performing CMP processes.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 추계학술대회 논문집 Vol.18
• /
• pp.358-359
• /
• 2005

Chemical mechanical polishing(CMP) process depends on a variety of variables. Especially, surface roughness of pad plays a key role in material removal in CMP in terms of transportation ability of pores and real contact area. The surface roughness is deteriorated with polishing time by applied pressure and relative velocity. In this reason, diamond conditioner has been used to maintain the roughness on the pad. The authors try to investigate the correlation between pad roughness and frictional behavior by comparing ex-situ conditioning with in-situ conditioning.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권12호
• /
• pp.549-554
• /
• 2006

In this paper we first applied the chemical mechanical polishing (CMP) process to the planarization of ferroelectric film in order to obtain a good planarity between electrode and ferroelectric film. $Pb_{1.1}(Zr_{0.52}Ti_{0.48})O_3$ (shortly PZT) ferroelectric film was fabricated by the sol-gel method. And then, we compared the structural characteristics before and after CMP process of PZT films. Removal rate, WIWNU% and surface roughness have been found to depend on slurry abrasive types and their hardness, especially, surface roughness and planarity were strongly depends on its pH value. A maximum in the removal rate is observed in the silica slurry, in contrast with the minimum removal rate occurs at ceria slurry. We found that the surface roughness of PZT films can be significantly reduced using the CMP technique.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.935-938
• /
• 1997

Recently, the minimum line width shows a tendency to decrease and the multi-level increase in semiconductor. Therefore, a planarization technique is needed and chemical mechanical polishing(CMP) is considered as one of the most suitable process. CMP accomplishes a high polishing performance and a global planarization of high quality. But there are several defects in CMP such as micro-scratches, abrasive contaminations, and non-uniformity of polished wafer edges. Wet etching include of Spin-etching can improve he defects of CMP. It uses abrasive-free chemical solution instead of slurry. On this study, ILD(INterlayer-Dielectric) was removed by CMP and wet-etching methods in order to investigate the superiority of wet etching mechanism. In the thin film wafer, the results were evaluated at a viewpoint of material removal rate(MRR) and within wafer non-uniformity(WIWNU). And pattern step height was also compared for planarization characteristics of the patterned wafer.

• 대한기계학회논문집A
• /
• 제33권3호
• /
• pp.196-200
• /
• 2009

Lithium niobate ($LN:LiNbO_3$) is a compound of niobium, lithium and oxygen. The characteristics of LN are piezoelectricity, ferroelectricity and photoelectricity, and which is widely used in surface acoustic wave (SAW). To manufacture LN devices, the LN surface should be a smooth surface and defect-free because of optical property, but the LN material is processed difficult b traditional processes such as grinding and mechanical polishing (MP) because of its brittleness. To decrease defects, chemical mechanical polishing (CMP) was applied to the LN wafer. In this study, the suitable parameters such as down force and relative velocity, were investigated for the LN CMP process To improve roughness, the LN CMP was performed using the parameters that were the highest removal rate among process parameters. And, evaluation of optical property was performed by the optical reflectance.

• Tribology and Lubricants
• /
• 제37권6호
• /
• pp.208-212
• /
• 2021

Chemical mechanical polishing (CMP) is a key technology used for the global planarization of thin films in semiconductor production and smoothing the surface of substrate materials. CMP is a type of hybrid process using a material removal mechanism that forms a chemically reacted layer on the surface of a material owing to chemical elements included in a slurry and mechanically removes the chemically reacted layer using abrasive particles. Sapphire is known as a material that requires considerable time to remove materials through CMP owing to its high hardness and chemical stability. This study introduces a technology using electrolytic ionization and ultraviolet (UV) light in sapphire CMP and compares it with the existing CMP method from the perspective of the material removal rate (MRR). The technology proposed in the study experimentally confirms that the MRR of sapphire CMP can be increased by approximately 29.9, which is judged as a result of the generation of hydroxyl radicals (·OH) in the slurry. In the future, studies from various perspectives, such as the material removal mechanism and surface chemical reaction analysis of CMP technology using electrolytic ionization and UV, are required, and a tribological approach is also required to understand the mechanical removal of chemically reacted layers.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제3C권1호
• /
• pp.28-32
• /
• 2003

In this paper, we have studied the in-situ end point detection (EPD) for direct chemical mechanical polishing (CMP) of shallow trench isolation (STI) structures without the reverse moat etch process. In this case, we applied a high selectivity $1n (HSS) that improves the silicon oxide removal rate and maximizes oxide to nitride selectivity Quite reproducible EPD results were obtained, and the wafer-to-wafer thickness variation was significantly reduced compared with the conventional predetermined polishing time method without EPD. Therefore, it is possible to achieve a global planarization without the complicated reverse moat etch process. As a result, the STI-CMP process can be simplified and improved using the new EPD method.