• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.139-147
• /
• 2021

Livestock manure is used as an organic fertilizer to replace chemical fertilizers after sufficient fermentation in an aerobic bioreactor. On the other hand, liquid manure disposal problems occur repeatedly because soil spraying is restricted during the summer when the crops are growing. To use liquid fertilizer (LF) as an additional nutrient source for crops, it is necessary to reduce the amount of suspended solids (SS) in the liquid fertilizer and secure stability problems against pathogenic microorganisms. This study examined the effects of the simultaneous SS removal and E.coli sterilization in the LF using the microbubble (MB) generator (FeMgO catalyst insertion). The remaining SS were further removed using the integrated microbubble and microfilter system. During the floating process in the MB device, the SS were removed by 57.9%, and the coliform group was not detected (16,200→0 MPN/100 mL). By optimizing the HRT of the integrated system, the removal efficiency of the SS was improved by 92.9% under the 0.1h of HRT condition. After checking the properties of the treated LF, 64.5%, 70.1%, 54.9%, and 51.5% of the TCOD, SCOD, PO4-P, and TN, respectively, were removed. The treated effluent from such an integrated system has a lower SS content than that of the existing LF and does not contain coliforms; therefore, it can be used directly as an additional fertilizer.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.1
• /
• pp.8-15
• /
• 2021

TiO2 has been used in various fields such as solar cells, dental implants, and photocatalysis, because it has high physical and chemical stability and is harmless to the body. TiO2 nanofibers which have a large specific surface area also show a good reactivity in bio-friendly products and excellent photocatalysis in air and water purification. To fabricate TiO2 nanofibers, an electrospinning method was used. To observe the diameter of TiO2 nanofibers with fabrication variables, the fabrication variables was divided into precursor composition variables and process variables and microstructure was analyzed. The concentrations of PVP (Polyvinylpyrrolidone) and TTIP (Titanium(IV) isopropoxide) were selected as precursor composition variables, and inflow velocity and voltage were also selected as process variables. Microstructure and crystal structure of TiO2 nanofibers were analyzed using FE-SEM (Field emission scanning electron microscope) and XRD (X-ray diffraction), respectively. As-spun TiO2 nanofibers with an average diameter of about 0.27 ㎛ to 1.31 ㎛ were transformed to anatase TiO2 nanofibers with an average diameter of about 0.22 ㎛ to 0.78 ㎛ after heat treatment of 3 hours at 450℃. Anatase TiO2 nanofibers with an average diameter of 0.22 ㎛ can be expected to improve the photocatalytic properties by increasing the specific surface area. To change the average diameter of TiO2 nanofibers, the control of precursor composition variables such as concentrations of PVP and TTIP is more efficient than the control of electrospinning process variables such as inflow velocity and voltage.

• Composites Research
• /
• v.34 no.4
• /
• pp.241-248
• /
• 2021

As the electric vehicle market grows, there is an issue of light weight vehicles to increase battery efficiency. Therefore, it is going to replace the battery module cover that protects the battery module of electric vehicles with high strength/high heat-resistant polymer composite material which has lighter weight from existing aluminum materials. It also aims to respond to the early electric vehicle market where technology changes quickly by combining 3D printing technology that is advantageous for small production of multiple varieties without restrictions on complex shapes. Based on the composite material mechanics, the critical length of glass fibers in short glass fiber (GF)/polycarbonate (PC) composite materials manufactured through extruder was derived as 453.87 ㎛, and the side feeding method was adopted to improve the residual fiber length from 365.87 ㎛ and to increase a dispersibility. Thus, the optimal properties of tensile strength 135 MPa and Young's modulus 7.8 MPa were implemented as GF/PC composite materials containing 30 wt% of GF. In addition, the filament extrusion conditions (temperature, extrusion speed) were optimized to meet the commercial filament specification of 1.75 mm thickness and 0.05 mm standard deviation. Through manufactured filaments, 3D printing process conditions (temperature, printing speed) were optimized by multi-optimization that minimize porosity, maximize tensile strength, and printing speed to increase the productivity. Through this procedure, tensile strength and elastic modulus were improved 11%, 56% respectively. Also, by post-processing, tensile strength and Young's modulus were improved 5%, 18% respectively. Lastly, using the FEA (finite element analysis) technique, the structure of the battery module cover was optimized to meet the mechanical shock test criteria of the electric vehicle battery module cover (ISO-12405), and it is satisfied the battery cover mechanical shock test while achieving 37% lighter weight compared to aluminum battery module cover. Based on this research, it is expected that 3D printing technology of polymer composite materials can be used in various fields in the future.

• Economic and Environmental Geology
• /
• v.54 no.4
• /
• pp.409-425
• /
• 2021

Carbon dioxide has been known to be a typical greenhouse gas causing global warming, and a number of efforts have been proposed to reduce its concentration in the atmosphere. Among them, carbon dioxide capture and storage (CCS) has been taken into great account to accomplish the target reduction of carbon dioxide. In order to commercialize the CCS, its safety should be secured. In particular, if the stored carbon dioxide is leaked in the arable land, serious problems could come up in terms of crop growth. This study was conducted to investigate the effect of carbon dioxide leaked from storage sites on soil fertility. The leakage of carbon dioxide was simulated using the facility of its artificial injection into soils in the laboratory. Several soil chemical properties, such as pH, cation exchange capacity, electrical conductivity, the concentrations of exchangeable cations, nitrogen (N) (total-N, nitrate-N, and ammonia-N), phosphorus (P) (total-P and available-P), sulfur (S) (total-S and available-S), available-boron (B), and the contents of soil organic matter, were monitored as indicators of soil fertility during the period of artificial injection of carbon dioxide. Two kinds of soils, such as non-cultivated and cultivated soils, were compared in the artificial injection tests, and the latter included maize- and soybean-cultivated soils. The non-cultivated soil (NCS) was sandy soil of 42.6% porosity, the maize-cultivated soil (MCS) and soybean-cultivated soil (SCS) were loamy sand having 46.8% and 48.0% of porosities, respectively. The artificial injection facility had six columns: one was for the control without carbon dioxide injection, and the other five columns were used for the injections tests. Total injection periods for NCS and MCS/SCS were 60 and 70 days, respectively, and artificial rainfall events were simulated using one pore volume after the 12-day injection for the NCS and the 14-day injection for the MCS/SCS. After each rainfall event, the soil fertility indicators were measured for soil and leachate solution, and they were compared before and after the injection of carbon dioxide. The results indicate that the residual concentrations of exchangeable cations, total-N, total-P, the content of soil organic matter, and electrical conductivity were not likely to be affected by the injection of carbon dioxide. However, the residual concentrations of nitrate-N, ammonia-N, available-P, available-S, and available-B tended to decrease after the carbon dioxide injection, indicating that soil fertility might be reduced. Meanwhile, soil pH did not seem to be influenced due to the buffering capacity of soils, but it is speculated that a long-term leakage of carbon dioxide might bring about soil acidification.

• Korean Journal of Mineralogy and Petrology
• /
• v.35 no.1
• /
• pp.65-73
• /
• 2022

The proper estimation of physical and chemical properties of Earth materials and their structures at high pressure and high temperature conditions is key to the full understanding of diverse geological processes in Earth and planetary interiors. Multi-anvil press - high-pressure generating device - provides unique information of Earth materials under compression, mainly relevant to Earth's upper mantle. The quantitative estimation of the relationship between the oil load within press and the actual pressure conditions within the sample needs to be established to infer the planetary processes. Such pressure-load calibration has often been based on the phase transitions of crystalline earth materials with known pressure conditions; however, unlike at high temperature conditions, phase transitions at low (or room) temperatures can be sluggish, making the calibration at such conditions challenging. In this study, we explored the changes in Al coordination environments of permanently densified pyrope glasses upon the cold compression using the high-resolution ²⁷Al MAS and 3QMAS NMR. The fractions of highly coordinated Al in the cold compressed pyrope glasses increase with increasing oil load and thus, the peak pressure condition. Based on known relationship between the peak pressure and the Al coordination environment in the compressed pyrope glasses at room temperature, we established a room temperature pressure-load calibration of the 14/8 HT assembly in 1,100-ton multi-anvil press. The current results highlight the first pressure-load calibration of any high pressure device using high-resolution NMR. Irreversible structural densification upon cold compression observed for the pyrope glasses provides insights into the deformation and densification mechanisms of amorphous earth materials at low temperature and high pressure conditions within the subducting slabs.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.30 no.3
• /
• pp.13-22
• /
• 2022

In order to improve water quality of the water system contaminated with dyes, biochars prepared using discarded waste resources were applied in this study. Biochars with a large specific surface area were manufactured using street tree pruning products or waste wood, and were applied to remove an organic dye in synthetic water. Biochars were made by pyrolysis of typical street tree porch products (Platanas, Ginkgo, Aak) and waste wood under air-controlled conditions. Methylene blue (MB), which is widely used in phosphofibers, paper, leather, and cotton media, was selected in this study. The adsorption capacity of Platanas for MB was the highest and the q_max value obtained using the Langmuir model equation was 78.47 mg/g. In addition, the adsorption energy (E) (kJ/mol) of MB using the Dubinin-Radushkevich (D-R) model equation was 4.891 kJ/mol which was less than 8 kJ/mol (a criteria distinguishing physical adsorption from chemical adsorption). This result suggests a physical adsorption with weak interactions such as van der Waals force between the biochar and MB. In addition, the physical adsorption may resulted from that Platanas-based biohar has the largest specific surface area and pore volume. The ∆G value obtained through the adsorption experiment according to temperature variation was -3.67 to -7.68, which also suggests a physical adsorption. Considering these adsorption results, the adsorption of MB onto Platanas-based biochar seems to occur through physical adsorption. Overall, it was possible to suggest that adsorption capacity of the biochr prepared from this study was equal to or greater than that of commercial activated carbon reported in other studies.

• Journal of Mushroom
• /
• v.20 no.3
• /
• pp.168-172
• /
• 2022

This study was conducted to investigate the optimum supplementation ratio when replacing cotton seed meal with rapeseed meal for cultivating oyster mushrooms. The chemical properties among the treatments were pH 4.5~4.7, total carbon content was 46.3~46.5%, total nitrogen content was 1.6~1.7%, and carbon-nitrogen ratio was 27.0~27.8. These did not differ significantly from the control. Mycelial growth was 85.1 mm (Heuktari), and 72.8 mm (Suhan-1Ho) in medium containing 5% rapeseed meal, with no significant difference in mycelial density between cultivars. Fruiting body characteristics are as follows: In 'Heuktari', the color of the pileus was darker than control with an L value of 32.5, and pileus thickness and diameter were 3.2 mm and 27.6 mm, respectively. Stipe length and diameter were 86.0 mm and 9.1 mm, respectively. Valid stipe number per bottle (1,100 cc) was 25.9, and a yield of 189.7 g/1,100 cc was recorded in mixed medium containing 5% rapeseed meal (higher than control). In mixed medium containing 10% rapeseed meal, the yield was 184.5 g/1,100 cc (comparable to control). In 'Suhan-1Ho', supplemented with 5% rapeseed meal, pileus color was darker than control color, with an L value of 28.8. Pileus thickness was 4.5 mm. Stipe diameter was 12.3 mm (higher than control), and yield was 145.5 g/1,100 cc (comparable to control).

• Journal of the Korea Organic Resources Recycling Association
• /
• v.30 no.2
• /
• pp.17-28
• /
• 2022

The application of supplemental activated biochar pellet fertilizers (ABPFs) was evaluated by investigating key factors such as changes of surface paddy water and soil chemical properties and rice growth responses during the growing season. The treatments consisted of control, activated rice hull biochar pellet (ARHBP-40%), and activated palm biochar pellet (APBP-40%) applications. It was shown that the lowest NH₄⁺-N and PO₄^--P concentrations were observed in surface paddy water to the ARHBP-40%, while the NH₄⁺-N concentration in the control was abruptly decreased until 30 days after transplant in the soil. However, the lowest NH₄⁺-N concentration in the blended biochar application was 9.18 mg L^-1 at 1 day of transplant, but its ABPFs application was observed to be less than 1 mg L^-1 at 56 days after transplant. The lowest PO₄^--P concentration in paddy water treated ARHBP-40% ranged from 0.06 mg L^-1 to 0.08 mg L^-1 until 30 days after transplant among the treatments. For the paddy soil, the NH₄⁺-N concentration in the control was abruptly decreased from 177.7 mg kg^-1 to 49.4 mg kg^-1, while NO₃^--N concentration was highest, 13.2 mg kg^-1 in 14 days after transplant. The P₂O₅ concentrations in the soils increased from rice transplants until the harvesting period regardless of the treatments. The highest K₂O concentration was 252.8 mg kg^-1 in the APBP-40% at 84 days after transplant. For the rice growth responses, plant height in the control was relatively high compared to others, but grain yield was not significantly different between the control and ARHBP-40%. The application of ARHBP-40% can minimize nitrogen and phosphorous application rates into the agro-ecosystem.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.38 no.3
• /
• pp.264-274
• /
• 1993

This study was carried out to assess the agronomic characters and physicochemical properties of floury and chalky-endosperm mutant lines induced by chemical mutagen treatment to rice varieties, Hwacheongbyeo and IR24. Linkage analysis of a floury-endosperm gene was carried out using linkage testers. The grain size of brown rice of the mutants was smaller than that of the original varieties. The l, 000-grain and 1$\ell$ weight were lighter in the mutants compared with those in the original varieties. The compound starch granules in the endosperm cell of the mutants showed a loosely-packed crystalline structure. Amylose contents in mutants ranged from 16.9 to 28.5%. Crude protein contents of the mutants were not significantly different from the original rice variety, Hwacheongbyeo, but white core mutant(line 47106) derived from IR24 showed higher protein(l1.32%) compared with IR24(8.30%). The mutants showed slightly harder gel characteristics, and much lower viscosity in Amylograph than original varieties. Steamed rice-cakes from mutant lines showed greater volume than those from original varieties. During the process of alcohol fermentation, Brix in the mutants(especially floury mutants) decreased faster and the alcohol production after 10-day fermentation was much greater in the mutants than in the original varieties. Three different gene loci for floury endosperm characteristics were identified from the allelism test among mutant lines, and the genes were tentatively symbolized as flo-a, flo-b and flo-c, respectively. A floury gene, flo-a, was linked with lg(liguleless) gene in the linkage group N, with R.V. 5.76$\pm$1.72%.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.15 no.1
• /
• pp.95-105
• /
• 2013

This study has been conducted to investigate the effect of Urea and K₂SO₄ treatment at stone hardening stage and 20 days before harvest on soil chemical properties, mineral nutrient concentration and quality of 'Mibaekdo' fruit peach. K concentration after Urea and K₂SO₄ treatment in soil was increased significantly by Urea 162g+K₂SO₄ 188g/tree(standard amount) treatment at stone hardening stage, K₂SO₄ 1.0% tree-spray, Urea 81g+K₂SO₄ 94g/tree(half amount), Urea 162g+K₂SO₄ 188g/tree and Urea 324g+K₂SO₄ 376g/tree(double amount) soil treatment before harvest 20 days compared to control. T-N, K and Ca concentration in leaf was increased significantly by all treatment. but Na concentration in leaf was increased by Urea 0.5% and K₂SO₄ 1.0% tree-spray treatment before harvest 20 days. T-N concentration in fruit skin was increased significantly by standard amount soil treatment, which decreased by K₂SO₄ 1.0% tree-spray and half amount soil treatment. T-N, K and Ca concentration in fruit flesh(1~10mm depth flesh from peel) were increased markedly by all treatment excepted Urea 0.5% tree-spray. The leaf weight at harvest was increased markedly by Urea 0.5% tree-spray, standard amount and double amount treatment before harvest 20 days. Fruit weight was increased significantly by standard amount compared to all treatment. Red fruit skin(Hunter a value) progress was effective by K₂SO₄ tree-spray, half amount and double amount treatment before harvest 20 days. Fruit SSC was increased significantly by Urea 0.5% and K₂SO₄ tree-spray before harvest 20 days, standard amount treatment at stone hardening stage compared to control.