• Proceedings of the KSR Conference
• /
• 2007.05a
• /
• pp.780-785
• /
• 2007

Korean Train Express (KTX) has opened to commercial traffic since 2004 at maximum speed 300km/h, and Korea High-speed Railway (HSR-350x) was developed by Korean government, several institutes, and related companies. HSR-350x is now being investigated its performance and tested at the high speed line. In 2004 December, HSR-350x was run over 350km/h and proved its running performance. These high speed railways have 12 motors to transfer the traction effort or the braking force. In this paper, authors propose the construction the measurement system for monitoring the force transferred to the train from the motor. The system is installed to the tripod shaft which is located between the reduction gears and it measures the mechanical load directly.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.787-792
• /
• 2004

LRB(Lead rubber bearing) has small resistance force against slowly acting loadings such as temporal and creep loadings vice versa large resistance force against rapid loadings such as earthquake and braking loadings. By those mechanical characteristics, it has the advantage to reduce longitudinal load acting on abutments and piers, and moreover to in1prove the running stability of train by restricting the behavior of bridge under the required level. In this study, a stability evaluation method of CWR on the bridge with LRB is presented. Several parametric studies are carried to investigate how LRB contributes to the improvement of CWR stability.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.668-673
• /
• 2003

A wheel and axle failure can cause a derailment with its attendant loss of life and property. The service conditions of railway vehicles have become severe in recent years due to a general increase in operating speeds. Damages of railway wheel are a spalling by wheel/rail contact and thermal crack by braking heat etc. One of the main source of damage is a residual stress. therefore it is important to evaluate exactly. A Residual stress of wheel is formed at the process of heat treatment when manufacturing. it is changed by contact stress developed by wheel/rail contact. Distributions of residual stress vary according to a magnitude of wheel load, a magnitude of friction when acceleration and deceleration. The objective of this paper is to estimate the influence of wheel motion on the residual stress distribution in the vicinity of the running surface.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.437-438
• /
• 2012

대부분 소형풍력발전은 운전 범위 이상이 될 경우 시스템 보호를 위해 Dump Load 방식 또는 전기자 반작용을 사용하며 순간 단락 시 돌발 단락 전류에 의해 풍력 발전기의 기계적 손상이 발생 된다. 본 논문에서는 ATmega 128을 이용한 PWM의 제어 방식 적용하여 돌발 단락 전류 억제하는 시스템을 구성 하고자 한다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.771-775
• /
• 2011

This paper presents design process of linear induction motor in dynamic tester for catenary-current collection. To minimize length of rail for dynamic tester for catenary-current collection, accelerating performance of the linear induction motor is very important. So the design process of linear induction motor considered in this paper is different with general design process of linear induction motor, because dynamic tester has three type driving region, as accelerating region, constant speed region, and braking region. Considering accelerating performance of motor, distance and time from starting point to constant speed region were concerned for load condition of motor. Designed linear induction motor was analyzed by 2-dimensional finite element method. Using mechanical dynamics simulation with analysis result of 2-dimensional finite element method and accelerating performance of designed motor was proved.

• Journal of the Korean Society for Railway
• /
• v.6 no.2
• /
• pp.142-148
• /
• 2003

A wheel and axle failure can cause a derailment with its attendant loss of life and property. The service conditions of railway vehicles have become severe in recent years due to a general increase in operating speeds. Damages of railway wheel are a spatting by wheel/rail contact and thermal crack by braking heat etc. One of the main source of damage is a residual stress. therefore it is important to evaluate exactly. A Residual stress of wheel is formed at the process of heat treatment when manufacturing. it is changed by contact stress developed by wheel/rail contact. Distributions of residual stress vary according to a magnitude of wheel load, a magnitude of friction when acceleration and deceleration. The objective of this paper is to estimate the influence of wheel motion on the residual stress distribution in the vicinity of the running surface.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.6 no.5
• /
• pp.59-66
• /
• 2002

Long-rails in railways and high-speed railway are subjected to additional stresses resulted from the displacements inconsistence between upper structures, and this phenomenon is more remarkable in continuous bridges than in simple bridges. For the sake of safety, railways have to guarantee trains to stop safely without derailment even in the event of earthquake. The influences of acceleration, braking, and temperature were analyzed by static nonlinear method. But earthquake loads that require dynamic nonlinear analysis are not considered in these methods. Because linear relation between relative displacements of decks and rail stresses is not guaranteed at the nonlinear systems such as long rails on the bridges, it is required compute to rail stresses considering both braking and earthquake load by nonlinear dynamic analysis method. In this study, dynamic analysis method with material non-linearity for rails on continuous bridges according to the Taiwan High Speed Railway(THSR) Design Specification volume 9 was developed. And additional stresses and displacements of long rails for acceleration, braking, and earthquake loads were analyzed by this method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.11
• /
• pp.963-970
• /
• 2015

In this study, the pressurization characteristics of the small piezoelectric hydraulic pump for a brake system has been analyzed through modeling the full hydraulic pump components; the pump chamber, check valve, pump load, pump drive controller etc. To analyze the pressurization characteristics, the process of charging pressure in the chamber with stacked-layer piezoelectric actuator were firstly modeled. Secondly, the flow coefficient of the check valve in terms of valve opening has been calculated after computational fluid dynamics analysis, such as the pressure distribution around check valve and the flow rate, was conducted. Also the pump driving controller, which controls the input voltage to the actuator, was designed to make the load pressure follow the input pressure command. The simulation results find that it takes about 0.03ms to reach the operating load pressure required for the braking system. The simulation result was also verified through comparison to the result of the pump performance test.

• Journal of the Korean Institute of Gas
• /
• v.13 no.5
• /
• pp.1-6
• /
• 2009

This paper presents the fuel consumption effects of LPG vehicle depending on the atmospheric temperature, LP gas leakage of vaporizer, viscosity of engine oil and engine load conditions. The fuel consumption test results show that when the temperature of engine temperature rises, the fuel consumption efficiency increases in general. The fuel consumption efficiency for an atmosphere temperature of $24.2^{\circ}C$ is 13.6% high compared to that of $1^{\circ}C$. No leak vaporizer on fuel consumption efficiency is 5.3% high compared to that of the LP gas leak vaporizer. The fuel economy of new engine oils is just 1.1% high compared to that of used oils with a LPG vehicle mileage of 9,500km. This is not an influential factor compared with an atmospheric temperature and a LP gas leakage. The more important factors on the fuel consumption efficiency are driving conditions such as a rapid braking, abrupt start and fast acceleration. The test results indicate that the normal start is 32.3% high compared to that of an abrupt start and the fast acceleration is 10.8% high compared with that of an abrupt start. And the fuel consumption efficiency for a rapid braking is 18.3% higher than that of an abrupt start. These indicate that the driving condition is very important to reduce the fuel consumption rate.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.2
• /
• pp.183-190
• /
• 2015

Objective : Walking with a Material handling is an activity frequently undertaken by agricultural workers in Korea, due to the nature of their work. This study aimed to investigate differences in biomechanical variables according to the mechanical alignment of the lower limbs when walking with a heavy load, and to use this as basic data in the design of various working environments to reduce the skeletomuscular burden on the knee joint. Method : The study subjects comprised of 22 right-foot dominant adult men and women aged between 20 and 23 years. The subjects were divided into a varus or valgus group according to the mechanical alignment of the lower limb by using radiographic findings. The subjects walked without any load and with a load of 10%, 20%, or 30% of their body weight held in front of them. The Kwon3d XP program was used to calculate biomechanical variables. Results : The flexion/extension moment of the knee joint showed a decreasing trend with increased load, irrespective of the mechanical alignment of the lower limb, while the varus group did not show normal compensatory action when supported by one leg at the point of maximum vertical ground reaction force. In addition, in terms of the time taken, subjects showed no difficulties in one-foot support time up to 20%/BW, but at 30%/BW, despite individual differences, there was an increase in single limb. The increased load resulted in a decrease in the ratio of standing phase to ensure physical stability. The valgus group showed a trend of increasing the stability of their center of mass with increasing load, through higher braking power in the early standing phase. Conclusion : In conclusion, although there was no statistical difference in biomechanical variables according to the mechanical alignment of the lower limbs, the varus group showed a more irregular walking pattern with a Material handling than the valgus group, partially proving the association between lower limb alignment and walking with a Material handling.