• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.29B no.1
• /
• pp.34-42
• /
• 1992

This paper presents two fast least-squares lattice algorithms for adaptive nonlinear filters equipped with bilinear system models. The lattice filters perform a Gram-Schmidt orthogonalization of the input data and have very good numerical properties. Furthermore, the computational complexity of the algorithms is an order of magnitude snaller than previously algorithm is an order of magnitude smaller than previously available methods. The first of the two approaches is an equation error algorithm that uses the measured desired response signal directly to comprte the adaptive filter outputs. This method is conceptually very simple`however, it will result in biased system models in the presence of measurement noise. The second approach is an approximate least-squares output error solution. In this case, the past samples of the output of the adaptive system itself are used to produce the filter output at the current time. Results of several experiments that demonstrate and compare the properties of the adaptive bilinear filters are also presented in this paper. These results indicate that the output error algorithm is less sensitive to output measurement noise than the squation error method.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.10 no.1
• /
• pp.27-35
• /
• 1973

The electronic states of carrier capture centers in reverse biased point-contact germanium diodes have been investigated through the tomperature-and reverse voltage-characteristics of burst noise. The measured values of the time constants wllich represent the electronic states of the centers are extended up to greater than ten minutes, which are about 10,000 times greater than the ones obtained by other investigators. From the relation between these time constants and temperatures, the quasi-Peymi level and the activation energy of the center have been obtained.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.1
• /
• pp.37-42
• /
• 2001

Ridge regression is compared with multiple linear regression (MLR) for determination of Research Octane Number (RON) when the baseline and signal-to-noise ratio are varied. MLR analysis of near-infrared (NIR) spectroscopic data usually encounters a collinearity problem, which adversely affects long-term prediction performance. The collinearity problem can be eliminated or greatly improved by using ridge regression, which is a biased estimation method. To evaluate the robustness of each calibration, the calibration models developed by both calibration methods were used to predict RONs of gasoline spectra in which the baseline and signal-to-noise ratio were varied. The prediction results of a ridge calibration model showed more stable prediction performance as compared to that of MLR, especially when the spectral baselines were varied. . In conclusion, ridge regression is shown to be a viable method for calibration of RON with the NIR data when only a few wavelengths are available such as hand-carry device using a few diodes.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.4
• /
• pp.16-22
• /
• 2000

In order to predict the performance and the usefulness of the narrow-band underwater acoustic measurement system at design stage, whose error variance is not clearly described, in this study a boundary equation to estimate the measurement accuracy is proposed based on the confidency as SNR variation. The boundary is presented as a function of SNR and the number of samples. In this paper, the measurement performance for narrow-band signal is simulated by the proposed boundary equation and the results are reviewed in the biased noise condition and separately in the background noise rejected condition.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.804-809
• /
• 2003

In this study, 2D computations of the Aeolian tones for some obstacles (circular cylinder, square cylinder and NACA0012 airfoil) are simulated. First of all, we calculate the flow noise generated by a uniform flow around a two-dimensional circular cylinder at Re=150 are simulated by applying the finite difference lattice Boltzmann method (FDLBM). The third-order-accurate up-wind scheme (UTOPIA) is used for the spatial derivatives, and the second-order-accurate Runge-Kutta scheme is applied for the time marching. The results show that we successively capture very small acoustic pressure fluctuation with the same frequency of the Karman vortex street compared with the pressure fluctuation around a circular cylinder. The propagation velocity of the acoustic waves shows that the points of peak pressure are biased upstream due to the Doppler effect in the uniform flow. For the downstream, on the other hand, it is faster. To investigate the effect of the lattice dependence, furthermore, simulations of the Aeolian tones at the low Reynolds number radiated by a square cylinder and a NACA0012 airfoil with a blunt trailing edge at high incidence are also investigated.

• Progress in Superconductivity
• /
• v.5 no.1
• /
• pp.55-60
• /
• 2003

We designed and constructed integrated 3-channel flux-locked-loop (FLL) electronic system for the control and readout of high-T$_{c}$ SQUIDs. This system consists of low noise preamplifiers, integrators, interface circuits, and software. FLL operation was carried out with biased signals of 19 KHz modulated current and 150 KHz modulated flux, which are reconstructed as detected signals by preamplifier and demodulator. Computer controlled interface circuits regulate FLL circuit and adjust SQUID parameters to the optimum operating condition. The software regulates interface circuits to make an auto-tuning for the control of SQUIDs, and displays readout data from FLL circuit. 3-channel SQUID electronic system was assembled with 3 FLL-interface circuit boards and a power supply board in the aluminum case of 56 mm ${\times}$ 53 mm${\times}$ 150 mm. Overall noise of the system was around 150 fT/(equation omitted)Hz when measured in the shielded room, 200 fT/(equation omitted)Hz in a weakly shielded room, respectively.y.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.595-604
• /
• 2016

Utilizing a standard 130-nm CMOS process, a RF frontend is designed at 24 GHz for automotive collision avoidance radar application. Single IF direct conversion receiver (DCR) architecture is adopted to achieve high integration level and to alleviate the DCR problem. The proposed frontend is composed of a two-stage LNA and downconversion mixers. To save power consumption, and to enhance gain and linearity, stacked NMOS-PMOS $g_m$-boosting technique is employed in the design of LNA as the first stage. The switch transistors in the mixing stage are biased in subthreshold region to achieve low power consumption. The single balanced mixer is designed in PMOS transistors and is also realized based on the well-known folded architecture to increase voltage headroom. This frontend circuit features enhancement in gain, linearity, and power dissipation. The proposed circuit showed a maximum conversion gain of 19.6 dB and noise figure of 3 dB at the operation frequency. It also showed input and output return losses of less than -10 dB within bandwidth. Furthermore, the port-to-port isolation illustrated excellent characteristic between two ports. This frontend showed the third-order input intercept point (IIP3) of 3 dBm for the whole circuit with power dissipation of 6.5 mW from a 1.5 V supply.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.286-288
• /
• 2007

In this paper, the fast locking PLL Frequency Synthesizer with low phase noise in a 0.18um CMOS process is presented. Its main application IS for the 915MHz ISM band wireless transponder upon the CPFSK (Continuous Phase Frequency Shift Keying) modulation scheme. Frequency synthesizer, which in this paper, is designed based on self-biased techniques and is independent with processing technology when damping factor and bandwidth fixed to most important parameters as operating frequency ratio, broad frequency range, and input phase offset cancellation. The proposed frequecy synthesizer, which is fully-integrated and is in 320M $^{\sim}$ 960MHz of the frequency range with 10MHz of frequency resolution. And its is implemented based on integer-N architecture. Its power consumption is 50mW at 1.8V of supply voltage and core area is $540{\mu}m$ ${\times}$ $450{\mu}m$. The measured phase noises are -117.92dBc/Hz at 10MHz offset, with low settling time less than $3.3{\mu}s$.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.5
• /
• pp.717-727
• /
• 2004

In this study, we simulate the aerodynamic sounds generated by a two-dimensional circular cylinder in a uniform flow are simulated by applying the finite difference lattice Boltzmann method (FDLBM). The third-order-accurate up-wind scheme (UTOPIA) is used for the spatial derivatives. and the second-order-accurate Runge-Kutta scheme is applied for the time marching. The results show that we successively capture very small acoustic pressure fluctuations with the same frequency of the Karman vortex street compared with the Pressure fluctuation around a circular cylinder The propagation velocity of the acoustic waves shows that the points of peak pressure are biased upstream due to the Doppler effect in the uniform flow For the downstream. on the other hand. it quickly Propagates. It is also apparent that the amplitude of sound Pressure is Proportional to $r^{-1/2}$, r being the distance from the center of the circular cylinder. To investigate the effect of the lattice dependence furthermore a 2D computation of the tone noise radiated by a NACA0012 with a blunt trailing edge at high incidence and low Reynolds number is also investigated.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.559-564
• /
• 2002

Cross-talk cancellation, inverse filter design or deconvolution in a generic term, is a vital process for a virtual sound realization in the stereo sound reproduction system. Most, if not all, of the design algorithms available for the inverse filter are based on a linearized model of the real physical plant. The result of such a plant-based design method, which may be referred to here as the indirect method, is biased due to both modelling and inversion errors. This paper presents a novel direct cross-talk cancellation method that may be free from the inversion error. The direct method can directly models the inverse filter by a suitable rearrangement of the input and output ports of the original plant so that no inversion is required here. Advantages are discussed with various experiments in an anechoic chamber using a PC soundcard. Binaural reproduction tests conducted showed that the conventional indirect method yields about 8 % reproduction performance error on both ear positions, whereas the direct method offers about 3 %.