• ETRI Journal
• /
• v.36 no.5
• /
• pp.841-846
• /
• 2014

This study proposes a novel optical sensor structure based on a refractometer combining a bend waveguide with an air trench. The optical sensor is a $1{\times}2$ splitter structure with a reference channel and a sensing channel. The reference channel has a straight waveguide. The sensing channel consists of a U-bend waveguide connecting four C-bends, and a trench structure to partially expose the core layer. The U-bend waveguide consists of one C-bend with the maximum optical loss and three C-bends with minimum losses. A trench provides a quantitative measurement environment and is aligned with the sidewall of the C-bend having the maximum loss. The intensity of the output power depends on the change in the refractive index of the measured material. The insertion loss of the proposed optical sensor changes from 3.7 dB to 59.1 dB when the refractive index changes from 1.3852 to 1.4452.

• Korean Journal of Optics and Photonics
• /
• v.18 no.1
• /
• pp.50-55
• /
• 2007

Using the Selective Area Growth (SAG) technology of Metal Organic Chemical Vapor Deposition (MOCVD), we successfully integrated an active device and passive devices on the same substrate. In other words, we integrated a Semiconductor Optical Amplifier (SOA) as an active device and an S-bend waveguide and a Multi Mode Interference (MMI) waveguide as passive devices. The SOA is successfully integrated with passive devices on the same substrate. The Cross-Gain Modulation (XGM) characteristic of the integrated SOA and the loss of an MMI and an S-bend waveguide were measured. Measured XGM characteristics of the SOA showed an extinction ratio of 8.82 dB. The total loss of the MMI and S-bend waveguide was 18 dB.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.27-31
• /
• 2002

We design a 1$\times$4 optical splitter made of photonic crystal waveguides and analyze the properties of the optical splitter using the finite-difference time-domain method with perfectly-matched-layer absorbing boundaries. The photonic crystal is constructed from cylindrical rods in air on a square lattice. Our simulation results show that there are different transmission properties for four bend geometries and different incident-wave frequencies. The sum of the power transmission of the splitted light is over 93 percent at a certain geometry and frequency, and the incident power splits in the four arms with almost the same ratio.

• Laser Solutions
• /
• v.8 no.1
• /
• pp.9-18
• /
• 2005

The laser direct writing method using a UV Argon-ion laser is studied for fabrication of waveguide. The laser direct writing system is constructed with a vision camera, a xy-stage, a motion controller and the delivery components of a laser beam. The UV Argon-ion laser has wavelength range of $333.6\~363.8$ nm. A photo-active UV curable polymer for a planar light-wave circuit(PLC) of single mode is used. This polymer is irradiated by Argon-ion laser and developed by a solvent after a post-baking. The optimum laser direct writing condition is obtained experimentally by changing various process parameters such as laser power, writing speed and focal length. The propagation and coupling loss of a optical waveguide was measured as 1dB/cm and 0.6dB/cm, respectively. Also, the minimum width of waveguide of $100{\mu}m$(ZPLW-207) is obtained. Finally, the waveguides of line, bend and branch type are successfully fabricated.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.3
• /
• pp.80-90
• /
• 1995

The scattering parameters of a microstrip single line, a right-angle bend and a coupled line are calculated using the multiport network model for the frequency range from 1 to 18 GHz. The single line is analyzed using the planar waveguide model. The right-angle bend is broken into two rectangular segments, and each segment is analyzed in a similar fashion as the single line. Impedance matrices corresponding to the two segments are combined by the segmentation method. In the analysis of elec- tromagnetic coupling of the coupled line, a new method is employed resulting in much less computation time than those previous methods involving Green's functions. A good agreement between the numerical results for the three structures and those from SuperCompact reveals the usefulness of the multiport network medel in analyzing complicated mirostrip single and coupled line discontinuities.

• Proceedings of the IEEK Conference
• /
• 2003.07b
• /
• pp.1125-1128
• /
• 2003

This paper presents the design method of a Colpitts type oscillator with coplanar waveguide(CPW) structures in the range of Ka-band frequency for transmitter and receiver modules. Series short stubs of CPW patterns provide inductances and capacitances in the range of Ka-band which can be expressed as a CLC-$\pi$ equivalent circuit. The experimentation has employed ro4003 substrates as a CPW substrate which has a dielectric constant of 3.38 and a signal and ground space of 100um. A method of momentum simulation for the CPW patterns has performed with an ADS software tool of Hewlett-Packard Corp. Inductance and capacitance circuits of a Colpitts oscillator was interconnected to a MESFET with CPW bend structures of including the input and output impedance matching circuits of the active transistor. Circuit parameters for impedance matching were determined through the network conversion to the equivalent length of CPW transmission lines by using T-network 1 $\pi$-network conversion circuit. A Colpitts oscillator was fabricated on the substrate of a area of 8.5mm x 17.4mm with a MESFET of Fujitsu FMM5704X and CPW series short stubs. The design suggested the possibility of realizing oscillators on a planar surface for the wireless system of tansmitter and receiver modules in the frequency range of 30GHz

• Korean Journal of Optics and Photonics
• /
• v.8 no.2
• /
• pp.169-173
• /
• 1997

Most conventional lithography systems have been oriented to fabricate electronic devices. Therefore, it is not so easy to fabricate large aspect ratios of waveguide patterns with those systems. When considering costs and efficiencies, a laser lithography system provides number of benefit in realizing waveguide patterns. However, because the conventional laser lithography system could make only positive tone masks, it is inconvenient in determining the direction of the waveguide. A simple and reliable technique to produce negative tone masks was developed by using the laser beam writing. This technique was not sensitive to environmental situations such as dust, vibration, intensity variation. Making use of the technique a variety of device patterns such as Y-branch, directional coupler, and highly smooth S-shape bend could be successfully fabricated with a good contrast.

• Korean Journal of Optics and Photonics
• /
• v.19 no.1
• /
• pp.73-79
• /
• 2008

We propose a novel metal-waveguide structure for sustaining long-range surface-plasmon-polaritons (LRSPP). The LRSPP waveguides are composed basically of two asymmetric metal layers: a very thin, finite-width metal strip on top of a metal slab with a dielectric gap in between them. Mode cut-off of LRSPPs excited on the double-metal waveguides is characterized by consistently investigating their dispersion relations and mode profiles. We also confirm experimentally the existence of low-loss, well-confined LRSPP modes by measuring far-field outputs emerging from an edge of the asymmetric double-metal waveguides. In the experiment, we have fabricated several types of SPP waveguide devices including straight lines, S-bend, and Y-branch consisting of gold strips (20 nm-thick, $5{\mu}m$-wide). Overall propagation loss of the proposed double-metal waveguides is quite comparable to that of single metal-strip waveguides, in addition the mode sizes can be tuned by increasing the core-insulator gap between the metal layers to get a higher coupling efficiency with a single-mode fiber in telecom wavelength. The proposed LRSPP waveguides may open up realization of SPP-waveguide sensors or nonlinear SPP-devices by replacing the core-insulator with a bio-fluid or a nonlinear medium.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1778-1780
• /
• 2004

Microwave heating system of KSTAR consists of ECH and LHCD. ECH and LHCD offer the reliability of operation in the beginning of plasma formation and non-inductive current drive for long time steady state operation with maintaining MHD stability, respectively. LHCD demands 5 GHz of frequency and consists of c-band waveguide, 4-port circuitor, dry dummy load, dual directional coupler, E-bend, arc detector. Our system is a lineup type pulse modulator that has 45 kV of output pulse voltage, 90 A of pulse current, 4 us of pulse width. 1:4 step-up pulse transformer, 7 stages of PFN and thyratron tube (E2V, CX1191D) are used in this modulator. The purpose of this paper is to show the modulator design and experimental result.