• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.1-6
• /
• 2011

A transparent oxide thin film transistors (Transparent Oxide-TFT) have been fabricated by RF magnetron sputtering at room temperature using amorphous indium zinc oxide (a-IZO) as both of active channel and source/drain, gate electrodes and co-sputtered $HfO_2-Al_2O_3$ (HfAIO) as gate dielectric. In spite of its high dielectric constant > 20), $HfO_2$ has some drawbacks including high leakage current and rough surface morphologies originated from small energy band gap (5.31eV) and microcrystalline structure. In this work, the incorporation of $Al_2O_3$ into $HfO_2$ was obtained by co-sputtering of $HfO_2$ and $Al_2O_3$ without any intentional substrate heating and its structural and electrical properties were investigated by x-ray diffraction (XRD), atomic force microscopy (AFM) and spectroscopic ellipsometer (SE) analyses. The XRD studies confirmed that the microcrystalline structures of $HfO_2$ were transformed to amorphous structures of HfAIO. By AFM analysis, HfAIO films (0.490nm) were considerably smoother than $HfO_2$ films (2.979nm) due to their amorphous structure. The energy band gap ($E_g$) deduced by spectroscopic ellipsometer was increased from 5.17eV ($HfO_2$) to 5.42eV (HfAIO). The electrical performances of TFTs which are made of well-controlled active/electrode IZO materials and co-sputtered HfAIO dielectric material, exhibited a field effect mobility of more than $10cm^2/V{\cdot}s$, a threshold voltage of ~2 V, an $I_{on/off}$ ratio of > $10^5$, and a max on-current of > 2 mA.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.432-438
• /
• 2001

In this paper, after applying Defected Ground Structure(DGS) to DC block, changes of gap and length of λ/4 coupled line are investigated by EM simulation and fabrication. As a result, on condition of the same output with the case using typical DC block, the gap between λ/4 coupled line is widen from 0.1 mm to 0.46 mm by 0.36 mm and the length of λ/4 coupled line gets shorter from 17.7 mm to 13.2 mm by 4.5 mm. Also three type power amplifiers using blocking capacitor, typical DC block and DGS DC block are fabricated and investigated. At first, when S parameter characteristics of each amplifier are considered at frequency band of 3.2 +-0.O5 GHz, every amplifier has similar characteristics of gain and S parameter. Second when the output power of amplifiers is 25 dBm after putting CW signal of 3.2 GHz into three type amplifiers, the difference of dominant signal and 2nd harmonic signal using blocking capacitor, typical DC block and DGS DC block is each -44.83 dBc, -66.84 dBc and -64.33 dBc. Therefore harmonic characteristics of amplifiers using typical DC block and DGS DC block is almost same.

• Applied Chemistry for Engineering
• /
• v.25 no.5
• /
• pp.487-496
• /
• 2014

In this study, three kinds of polymers based on phenothiazine-benzothiadiazole were synthesized by a Suzuki coupling reaction, and the various side-chains were substituted at the nitrogen of phenothiazine. The optical and electrochemical properties of synthesized polymers were analyzed. The results indicate that their absorption ranged from 300 to 700 nm, and also confirmed the ideal highest occupied molecular orbital (HOMO) energy level was about -5.4 eV with low band-gap energy. Photovoltaic devices were fabricated using a photoactive layer composed of a blended solution of the polymer and $PC_{71}BM$ in ortho-dichlorobenzene The device with P2HDPZ-bTP-OBT containing the branched side-chain and long chain showed the best performance; the maximum power conversion efficiency of this device was 2.4% (with $V_{OC}$ : 0.74 V, $J_{SC}$ : $6.9mA/cm^2$, FF : 48.0%).

• Journal of the Korean Ceramic Society
• /
• v.53 no.4
• /
• pp.400-405
• /
• 2016

Ferric oxide (${\alpha}-Fe_2O_3$, hematite) is an n-type semiconductor; due to its narrow band gap ($E_g=2.1eV$), it is a highly attractive and desirable material for use in solar hydrogenation by water oxidation. However, the actual conversion efficiency achieved with $Fe_2O_3$ is considerably lower than the theoretical values because the considerably short diffusion length (2-4 nm) of holes in $Fe_2O_3$ induces excessive charge recombination and low absorption. This is a significant hurdle that must be overcome in order to obtain high solar-to-hydrogen conversion efficiency. In consideration of this, it is thought that elemental doping, which may make it possible to enhance the charge transfer at the interface, will have a marked effect in terms of improving the photoactivities of ${\alpha}-Fe_2O_3$ photoanodes. Herein, we report on the synthesis by pulsed electrodeposition of ${\alpha}-Fe_2O_3$-based anodes; we also report on the resulting photoelectrochemical (PEC) properties. We attempted Ti-doping to enhance the PEC properties of ${\alpha}-Fe_2O_3$ anodes. It is revealed that the photocurrent density of a bare ${\alpha}-Fe_2O_3$ anode can be dramatically changed by controlling the condition of the electrodeposition and the concentration of $TiCl_3$. Under optimum conditions, a modified ${\alpha}-Fe_2O_3$ anode exhibits a maximum photocurrent density of $0.4mA/cm^2$ at 1.23 V vs. reversible hydrogen electrode (RHE) under 1.5 G simulated sunlight illumination; this photocurrent density value is about 3 times greater than that of unmodified ${\alpha}-Fe_2O_3$ anodes.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.760-767
• /
• 2005

In this paper, we proposed a new type SIR bandpass filter using DAMLs. This filter is consisted of 2 layers with MEMS resonator layer and CPW feed line. DAMLs ring resonator is elevated with $10{\mu}m$ height from GaAs substrate. Using MEMS processing, we are able to realize SIR bandpass filter easily. Furthermore it is useful to integrate on conventional MMICs because it has CPW interfaces and ring resonator is isolated from substrate by air-gap. We optimized and measured the results that $S_{21}$ attenuation at rejected band is over 15 dB, insertion loss is inside the limit of 3 dB, and relative bandwidth is about $10\%$ at 60 GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.7
• /
• pp.1647-1652
• /
• 2010

A CdS film has been used as a window layer in CdTe and Cu(In,Ga)$Se_2$ thin films solar cell. Partial substitution of Zn for Cd increases the photocurrent and the open-circuit voltage by providing a match in the electron affinities of the two materials and the higher band gap. In this paper, CdZnS/CdTe and CdS/CdTe heterojunctions were fabricated and the electrical characteristics were investigated. Current-voltage-temperature measurements showed that the current transport for CdS/CdTe heterojunction was controlled by both tunneling and interface recombination. However, CdZnS/CdTe heterojunction displayed different current transport mechanism with the operating temperature. For above room temperature, the current transport of device was generation/recombination in the depletion region and was the leakage current and/or tunneling in the range below room temperature.

• Current Photovoltaic Research
• /
• v.5 no.1
• /
• pp.15-19
• /
• 2017

The fossil fuel power consumption generates $CO_2$, which causes the problems such as global warming. Also, the increase in energy consumption has accelerated the depletion of the fossil fuels, and renewable energy is attracting attention. Among the renewable energies, the solar energy gets a lot of attention as the infinite clean energy source. But, the supply level of solar cell is insignificant due to high cost of generation of electric power in comparison with fossil fuels. Thus several researchers are recently doing the research on ultra-low-cost solar cells. Also, $Cu_2O$ is one of the applied materials as an absorption layer in ultra-low-cost solar cells. Cuprous oxide ($Cu_2O$) is highly desirable semiconductor oxide for use in solar energy conversion due to its direct band gap ($E_g={\sim}2.1eV$) and a high absorption coefficient that absorbs visible light of wavelengths up to 650 nm. In addition, $Cu_2O$ has several advantages such as non-toxicity, low cost and can be prepared with simple and cheap methods on large scale. In this work, we fabricated the $Cu_2O$ thin films by reactive sputtering method. The films were deposited with a Cu target with variable parameters such as substrate temperature, rf-power, and annealing condition. Finally, we confirmed the structural properties of thin films by XRD and SEM.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.10
• /
• pp.625-630
• /
• 2017

ZnS was chemically deposited as a buffer layer alternative to CdS, for use as a Cd-free buffer layer in $Cu(In_{1-x}Ga_x)Se_2$ (CIGS) solar cells. The deposition of a thin film of ZnS was carried out by chemical bath deposition, following which the structural and optical properties of the ZnS layer were studied. For the experiments, zinc sulfate hepta-hydrate ($ZnSO_4{\cdot}7H_2O$), thiourea ($SC(NH_2)_2$), and ammonia ($NH_4OH$) were used as the reacting agents. The mole concentrations of $ZnSO_4$ and $SC(NH_2)_2$ were fixed at 0.03 M and 0.8 M, respectively, while that of ammonia, which acts as a complexing agent, was varied from 0.3 M to 3.5 M. By varying the mole concentration of ammonia, optimal values for parameters like optical transmission, deposition rate, and surface morphology were determined. For the fixed mole concentrations of $0.03M\;ZnSO_4{\cdot}7H_2O$ and $0.8M\;SC(NH_2)_2$, it was established that 3.0 M of ammonia could provide optimal values of the deposition rate (5.5 nm/min), average optical transmittance (81%), and energy band gap (3.81 eV), rendering the chemically deposited ZnS suitable for use as a Cd-free buffer layer in CIGS solar cells.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.9
• /
• pp.837-840
• /
• 2015

Graphene is a single layer of carbon material which shows very high electron mobility, so many kinds of research on the devices using graphene layer have been performed so far. Graphene material is adequate for high frequency and fast operation devices due to its higher mobility. In this research, the actual graphene layer is evaluated using RT-CVD method which can be available for mass production. The mobility of $7,800cm^2/Vs$ was extracted, that is more than 7 times of that in silicon substrate. The graphene transistor model having no band gap is evaluated using both of pMOS and nMOS based on the measured mobility values. And then the response of graphene transistor model regarding to gate length and width is examined.

• Journal of the Korean Magnetics Society
• /
• v.15 no.4
• /
• pp.231-235
• /
• 2005

We studied the microstructural evolution of ZrTM-Al (TM=Nb and Ti) alloy films, MR and electrical properties of the MTJ with $ZrTM-AlO_x$ barrier as a function of Zr/TM ratio. We observed that the ternary-oxide barrier reduced the TMR ratio due mainly to the structural defects such as the surface roughness. The change in TMR ratio and $V_h$ with Zr/TM ratio exactly corresponds to the systematic changes in the microstructural variation. Although the MTJ with ternary oxide reduced the TMR and the electrical stabilities, the junction resistances decreased as the Ti and Nb concentration increased due to the band-gap reduction caused by the formation of extra bands