• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.3
• /
• pp.300-305
• /
• 2013

The torque was calculated with inductance and iron loss. Because the linkage flux can change the inductance, and q-axis current can change the iron loss. Therefore, precise estimation of torque can achieve with the inductance and iron loss detail calculations. So, in this paper, the d, q-axis inductance was verified through CVCT(Current Vector Control Test) and DCT(Direct Current Test). Also in the iron loss calculation, the prediction of all areas of current magnitude, phase angle and speed was very difficult. And LUT(Look-Up Table) was spent time and resource largely. Therefore, iron loss mathematization was proposed according to current magnitude, phase angle and speed. Also, characteristics of IPMSM were comprised of analyzed and experimental values.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.200-202
• /
• 2004

ZnO thin films were grown at different plume-substrate angles by pulsed laser deposition(PLD). From the X-ray diffraction(XRD) result, all ZnO thin films were found to be well c-axis oriented and c-axis lattice constant approached the value of bulk ZnO as plume-substrate(P-S) angle decreased. The grain size of ZnO thin films measured by atomic force microscopy increased and the UV intensity of ZnO thin films investigated by photoluminescence increased as P-S angle decreased. It is found that the improvement of structural and optical properties mainly comes from the reduction of the flux of ablated species arriving on a substrate per a laser shot by tilting a substrate parallel to the plume propagation direction.

• Wind and Structures
• /
• v.28 no.3
• /
• pp.191-201
• /
• 2019

In this paper, the aerodynamic analysis of a vertical axis wind turbine was carried out by CFD approach to optimize the turbine performance. To perform numerical simulation, SST-Transition turbulence model was used, which demonstrated more precise results compared to non-transition models. A parametric study was conducted to optimize the VAWT performance based on the selected model. The investigation of pitch angle changes showed that the highest power produced by the turbine occurs at $2^{\circ}$ angle. Considering the effect of the rotor's arm junction to the airfoil showed that by increasing the distance of the junction from the edge of the airfoil from 25 cm to 40 cm, the power of the turbine increases by 60%. However, further increase in this distance results in power decrease. Based on the proposed numerical model, a case study was conducted to consider the installation of four VAWTs in the southwest corner of the medical science building at TMU campus with a height of 42m. The results of the simulation showed that 8.27 MWh energy is obtainable annually.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.8
• /
• pp.49-56
• /
• 1997

In recent years, ultrasonic technics has been widely applied to industrial fields and its application range has been expanded as a result of continuous research and development. This paper is concerned with development of post-processor program for ultrasonic test and two-axis automatic ultrasonic system for application of industrial fields. Test results of ultrasonic test post-processor program and two-axis auto- matic ultrasonic system have a good agreement with results of ultrasonic evaluation for defect detection in industrial fields. Therefore we think that the developed ultrasonic test post-processor program and two- axis automatic ultrasonic system in this work is very useful for application of industrial fields.

• Journal of the Korean Magnetic Resonance Society
• /
• v.10 no.1
• /
• pp.1-37
• /
• 2006

General expressions for solid state NMR lines are described for transitions under static, magic angle spinning, and variable angle spinning conditions in the case where the principal axis system for the anisotropic chemical shift tensor is noncoincident with that of the quadrupole coupling tensor. It is demonstrated that solid state NMR powder pattern simulation program VMAS based on the conventional grid point method of integrating over the Euler angle space is fast enough in comparison with the POWDER simulation package and Gauss-point method.

• KSTLE International Journal
• /
• v.1 no.2
• /
• pp.101-106
• /
• 2000

Variable displacement axial piston pumps are widely used for raising the energy level of the fluid in hydraulic systems. And the regulator is the device which regulates the discharge flow of the piston pump by controlling the swivel angle. The regulator receives the hydraulic pilot pressure and controls the pump output flow depending on the machine load and engine speed. This work deals with constant power control (horsepower control) in the design of a regulator by using a bent-axis type piston pump. In order to effectively use engine power, we must keep the horsepower from the engine to the pump constant. Therefore the regulator operates the constant power control. As a result, optimum power usage is obtained by accurately following the power hyperbola. This study focused on developing a simulation model of a regulator. First, the governing equations of the regulator are derived, and analysis is performed by computer simulation, which can identify significant parameters of regulator. As a result, the variation of the swivel angle, flow rate, hyperbolic curve, inner leakage and responsibility are simulated, and significant parameters of a regulator are identified.

• Korean Journal of Applied Biomechanics
• /
• v.21 no.1
• /
• pp.39-46
• /
• 2011

The purpose of this study was to examine differences between players who bend the left elbow and those who stretch it during the forward swing from BST to BC in a 2-handed backhand stroke among outstanding high school tennis players, and to assess the detailed 3D rotational kinematic characteristics of the shoulder and the hip. Statistically significant differences were observed between groups in the longitudinal axis rotation angle of the shoulder and the angle between the shoulder and the arm at BST, and in the side to side movement of the shoulder, the up and down movement of the hip, the side tilt angular velocity of the shoulder, the side tilt angular velocity of the hip, and the front tilt angular velocity of the hip at BC. The difference in the longitudinal axis rotation angle of the shoulder between the 2 groups suggests a difference in the flexibility of the joint in the shoulder arm racquet system. The longitudinal axis rotation angular velocity of the shoulder reached its peak at 75 % of the duration of the analyzed segment and then decreased little by little until BC. This time is considered the stage for increasing the angular velocity of the upper arm, the forearm, the hand and then the racquet, which are more distal segments than the shoulder.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.286-289
• /
• 2006

Temporal dual gamma drive technology employing the 120Hz refresh rate was developed to enhance the off-axis viewing quality in patterned vertical alignment mode. The color shift ${\Delta}u'v'$ from on-axis to off-axis (60 deg.) for pale orange color, (R,G,B) = (196,124,96), was below 0.01, and the power exponent of gamma curve for off-axis viewing angle (60 deg.) was about 1.8, when the gamma curve for on-axis was set with power exponent of 2.4. The off-axis image distortion index was below 0.180 in contrast to the normal case ${\sim}0.23$. To elevate the response speed of liquid crystal in the intra-frame, the voltage below threshold voltage of liquid crystals was used.

• Proceedings of KOSOMES biannual meeting
• /
• 2018.06a
• /
• pp.190-190
• /
• 2018

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.469-470
• /
• 2009