• Journal of Ceramic Processing Research
• /
• v.13 no.spc1
• /
• pp.149-153
• /
• 2012

Ti2AlN MAX-phase films were synthesized through the post-annealing process of as-deposited Ti-Al-N films. Near amorphous or quasi-crystalline ternary Ti-Al-N films were deposited on Si and Al2O3 substrates by sputtering a Ti2AlN MAX-phase target at room temperature, 300 ℃ and 450 ℃, respectively. A vacuum annealing of those films at 800 ℃ for 1 hour changed those films to crystalline Ti2AlN MAX-phase. The polycrystalline Ti2AlN MAX-phase films exhibited very excellent oxidation resistance due to its characteristics microstructure (nanolaminates), which has potential applications for high-temperature protective coatings. The microstructure and composition of Ti2AlN MAX-phase films were investigated using with a variety of characterization tools.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.2
• /
• pp.92-98
• /
• 2004

The current efficiency and the microstructure of the trivalent Cr deposits plated in flow cell system were investigated according to additives in sulfate bath and current density. The current efficiency of the deposits plated in the formic acid complexed bath was noticeably higher than that of the deposits from glycine complexed bath. The current efficiency of the deposits from the complexed baths with boric acid buffer increased linearly with current density in the range of 60-100 A/dm$^2$, while that of the deposits from the baths with both Al sulfate and mixed buffers increased parabolically with current density. The nodular crystallite size of the deposits increased with current density, and the deposits plated in low current density region had relatively smooth surface appearance with fine grains. The structure of the deposits from the complexed baths with boric acid buffer changed from amorphous structure to crystalline one with strong (110)peak with increasing current density. The deposits from the baths with both Al sulfate and mixed buffers had generally amorphous structure.

• Transactions of the Korean hydrogen and new energy society
• /
• v.8 no.4
• /
• pp.173-180
• /
• 1997

The Mechanically Alloyed $Ti_{0.7}Mg_{0.3}Ni$ was investigated as a function of milling time by X-ray diffraction, SEM(scanning electron microscope), EDS(energy dispersive spectrometer), P-C-Isotherm curves. After 10hrs milling, mixed $Ti_{0.7}Mg_{0.3}Ni$ powders were changed to amorphous phase. And amorphous $Ti_{0.7}Mg_{0.3}Ni$ alloys became TiNi phase crystalline after heat treatment at 873K in a vacuum for 1 hour. The hydrogen absorption capacity of the annealed $Ti_{0.7}Mg_{0.3}Ni$ alloy increased as a function of mechanical alloying time.

• The Korean Journal of Ceramics
• /
• v.3 no.3
• /
• pp.173-176
• /
• 1997

Direct metal ion beam deposition is considered to be a whole new thin film deposition technique. Unlike other conventional thin film deposition processes, the individual deposition particles carry its own ion beam energies which are directly coupled for the formation of this films. Due to the nature of ion beams, the energies can be controlled precisely and eventually can be tuned for optimizing the process. SKION's negative C- ion beam source is used to investigate the initial nucleation mechanism and growth. Strong C- ion beam energy dependence has been observed. Complete phase control of sp3 and sp3, control of the C/SiC/Si interface layer, control of crystalline and amorphous mode growth, and optimization of the physical properties for corresponding applications can be achieved.

• Nuclear Engineering and Technology
• /
• v.37 no.4
• /
• pp.299-308
• /
• 2005

The behavior of fission gas in all major types of nuclear fuel has been reviewed with an emphasis on more recently discovered aspects. It is proposed that the behavior of fission gas can be classified in a number of characteristic types that occur at a high or low operating temperature, and/or at high or low fissile burnup. The crystal structure and microstructure of the various fuels are the determinant factors in the proposed classification scheme. Three types of behavior, characterized by anisotropic $\alpha$-U, high temperature metallic $\gamma$-U, and cubic ceramics, are well-known and have been extensively studied in the literature. Less widely known are two equally typical low temperature kinds: one associated with fission induced grain refinement and the other with fission induced amorphization. Grain refinement is seen in crystalline fuel irradiated to high burnup at low temperatures, whereas breakaway swelling is observed in amorphous fuel containing sufficient excess free-volume. Amorphous fuel, however, shows stable swelling if insufficient excess free-volume is available during irradiation.

• Journal of Powder Materials
• /
• v.8 no.1
• /
• pp.42-49
• /
• 2001

Ti-50Ni(at%) and Ti-40Ni-10Cu(at%) alloy powders have been fabricated by ball milling method, and their microstructure and phase transformation behavior were investigated by means of scanning electron microscopy/energy dispersive spectrometry, differential scanning calorimetry (DSC), X-ray diffractions and transmission electron microscopy. In order to investigate the effect of ball milling conditions on transformation behavior, ball milling speed and time were varied. Ti-50Ni alloy powders fabricated with the milling speed more than 250 rpm were amorphous, while those done with the milling speed of 100rpm were crystalline. In contrast to Ti-50Ni alloy powders, Ti-40Ni-10Cu alloy powders were crystalline, irrespective of ball milling conditions. DSC peaks corresponding to martensitic transformation were almost discernable in alloy powders fabricated with the milling speed more than 250 rpm, while those were seen clearly in alloy powders fabricated with the milling speed of 100 rpm. This was attributed to the fact that a strain energy introduced during ball milling suppressed martensitic transformation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.124-124
• /
• 2009

We observed the changes of crystal structure of Rubrene (5,6,11,12-tetraphenylnaphthacene) polycrystal thin films at various in situ substrate temperature and process by scanning electron microscope(SEM), x-ray diffraction (XRD) and near-field microwave microprobe (NFMM). Amorphous rubrene thin film was initially obtained on 200 nm thick $SiO_2/Si$ substrate at 35 $^{\circ}C$ in a vacuum evaporation but in situ long time postannealing at the temperature 80 $^{\circ}C$ transformed the amorphous phase into crystalline. Four heating conditions are followed : (a) preheating (b) annealing (c) preheating, annealing (d) preheating, cooling(35 $^{\circ}C$), annealing. We have obtained the largest polycrystal disk in sample (c). But the highest crytallity and conductivity of the rubrene thin films were obtained in sample (d).

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1050-1053
• /
• 2002

In this paper, Amorphous silicon on glass substrate was recrystallized to poly-crystalline silicon by solid phase crystallization (SPC) technology. The active region of thin film transistor (TFT) was fabricated by amorphous silicon. The output and transfer characteristics of thin film transistor with lightly doped drain (LDD) structure was measured and analyzed. As a results, analyzed TFTs reliability with LDD's length by various kinds argument such as sub-threshold swing coefficient, mobility and threshold voltages were evaluated. Stress effects in TFT were able to improve to the characteristics of turn-on current and hot carrier effects by LDD's length variations.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.185-188
• /
• 2002

In this paper, Amorphous silicon on glass substrate was recrytallized to poly-crystalline silicon by solid phase crystallization(SPC) technology The active region of thin film transistor(TFT) was fabricated by amorphous silicon. The output and transfer characteristics of thin film transistor with lightly doped drain(LDD) structure was measured and analyzed. As a results, analyzed TFT's reliability with LDD's length by various kinds argument such as sub-threshold swing coefficient, mobility and threshold voltages were evaluated. Stress effects in TFT were able to improve to the characteristics of turn-on current and hot carrier effects by LDD's length variations

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.245-249
• /
• 2000

Consolidation of amorphous powders is emerging as a route for synthesis of high strength composite materials. Diffusion processes necessary for consolidation are expected to be more rapid in amorphous state(SRO) than in the crystalline state(LRO). A new synthesis technique of exploiting polymeric ceramic precursors(polysilazane and polyborosilazane) is derived for Si$_3$N$_4$/SiC and boron-modified nanocomposites for extremely high temperature applications up to 200$0^{\circ}C$. The characterization methods include thermal analysis of DTA, and XRD, NMR, TEM, after pyrolysis, as a function of time and temperature.