• 대한치과기공학회지
• /
• 제9권1호
• /
• pp.51-55
• /
• 1987

One of the primary advantages of acrylic resin teeth is their ability to bond chemically to the denture base resins. Fracture od acrylic resin teeth from a maxillary denture, however, is not uncommon. Bonding failures have been attributed to faulty boil-out procedures that fail to eliminate all traces of wax from the ridge lap surfaces of the teeth and to contamination of the ridge lap surface by careless application of tinfoil substitute. Attempts to increase the strength of the bond between acrylic resin teeth and heat-cured denture base resin include grinding the glossy ridge lap surface (in fluid system), painting the ridgelap surface of the teeth with monomer-polymer solution, and cutting retention grooves in the ridge lap surface of the teeth. This latter method has been tested by applying a tensile force in a labial direction to the incisal part of the lingual surface of the acrylic resin teeth. A progressive shear compressive load was applied at an angle to the lingual surface of acrylic resin teeth bonded to denture base acrylic resin. No statistically singificant advantage was derived by preparing retention grooves of different shapes in the ridgelap surface of the denture teeth.

• 한국응용과학기술학회지
• /
• 제30권3호
• /
• pp.567-574
• /
• 2013

For this research, prepared water soluble milk casein resin and waterborne polyurethane-acrylic resin. Use these resin, this article has been analyzed about change of mechanical properties by increasing amount of casein resin in polyurethane-acrylic resin on coated leather. According to measure data for solvent resistance, WPA(waterborne polyurethane-acrylic resin) resin and WPA-C1, C2, C3(samples of polyurethane-acrylic resin with milk casein resin) had good property. As known in the results, increase of casein constant did not influence to big change of hybrid resin properties. As test of tensile strength, WPA had lowest tensile characteristic(1.598 $kg_f/mm^2$) and WPA-C3 had highest tensile characteristic(1.718 $kg_f/mm^2$). Also best properties of abrasion was WPA-C3(06.021 mg.loss). In elongation case, WPA had best properties(754 %) in this experiment.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2011년도 춘계학술발표회 논문집
• /
• pp.339-347
• /
• 2011

This study was carried out in order to manufacture the high quality coated paper. High quality coated paper includes not only present state but also the state of the future. So in this study, acrylic-styrene emulsion which polymerized in laboratory was compared with SB(Styrene-butadiene) latex during thermal aging. The coated paper with three different formulations which controlled the dosage of acrylic-styrene emulsion were prepared. The coated paper were thermally aged at $105^{\circ}C$ for 18days and the optical properties were measured. Brightness, whiteness and CIE L value were higher during thermal aging with increasing amount of acrylic-styrene emulsion. CIE $a^*$ value was higher and CIE $b^*$ value decreased with increasing amount of acrylic-styrene emulsion. These results indicate that high quality coated paper which has anti -thermal aging property can be manufactured with acrylic-styrene emulsion.

• Fibers and Polymers
• /
• 제7권3호
• /
• pp.295-304
• /
• 2006

High-bulk worsted yams with different shrinkable and non-shrinkable acrylic fibers blend ratios are produced and then single jersey weft knitted fabrics with three different structures and loop lengths are constructed. The physical properties of produced yams and compression properties of produced fabrics at eight pressure values (50, 100, 200, 500, 1000, 1500 and $2000 g/cm^2$) were measured using a conventional fabric thickness tester. Then, weft-knitted fabric compression behavior was analyzed using a two parameters model. It is found that at 40 % shrinkable fibre blending ratio the maximum yam bulk, shrinkage, abrasion resistance and minimum yarn strength are obtained. It is also shown that high-bulk acrylic yarn has the highest elongation at 20 % shrinkable fibre blend ratio. The statistical regression analysis revealed that the compression behavior of acrylic weft-knitted fabrics is highly closed to two parameter model proposed for woven fabrics. It is also shown that for weft-knitted structure, there is an incompressible layer (V') which resists against high compression load. Acrylic weft-knitted fabrics with knit-tuck structure exhibit higher compression rigidity and lower softness than the plain and knit-miss structures. In addition, at 20 % shrinkable fibre blend ratio, the high-bulk acrylic weft-knitted fabrics are highly compressible.

• 한국응용과학기술학회지
• /
• 제25권1호
• /
• pp.1-14
• /
• 2008

To prepare weather-resistant modified silane acrylic resin coatings for an architectural purpose, tetrapolymers were synthesized by radical polymerization. 3-Methacryloxypropyltrimethoxysilane (MPTS) as a silicone monomer and n-butyl acrylate, methyl methacrylate, and n-butyl methacrylate as acrylic monomers were used. The composition of monomers was adjusted to fix the glass transition temperature of acrylic polymer for $20^{\circ}C$. The composition of MPTS in the synthesized polymer were varied from 10 wt% to 30 wt%. On the basis of synthesized resin amber paints were prepared and their physical properties and effects on weatherability were examined. The presence of MPTS in modified silane acrylic resins generally resulted in low molecular weight and broad molecular weight distribution, and also lowered the viscosity of the copolymers. The coated films prepared from these resins showed good and balanced properties in general. Adhesion to the substrate was outstanding in particular. Weatherability tests were carried out in three different types such as outdoor exposure, QUV, and SWO. The test results showed that the modified silane acrylic resins containing 30 wt% of MPTS had superior weathering properties.

• Journal of Electrical Engineering and Technology
• /
• 제2권1호
• /
• pp.106-111
• /
• 2007

Laser cutting with the micro-control technique has great potential to be employed for acrylic machining. In this paper, the optimal conditions of acrylic etching have been investigated. The three parameters such as laser power, moving velocity, and thickness of acrylic are experimented to find out optimal conditions. From these experimental results, we have known that it is very important to control accurate power by the TRIAC switching technique. The best condition of acrylic etching is performed 10 Wand 72 mm/sec at the plastic thickness of 1.33 mm. The other case is performed 10 W and 48 mm/sec, and 12 W and 56 mm/sec at the acrylic thickness of 2.00mm, respectively.

• 치과방사선
• /
• 제26권2호
• /
• pp.133-145
• /
• 1996

Aspirating or swallowing foreign bodies is a common occurrence. If they are wholly or partly radiopaque, their localization in and progress through the gastrointestinal tract can be more effective. Of the dental origin foreign materials swallowed, the most common things are fragments of anterior maxillary partial denture. But the radiopacity of denture base resins is not sufficient to determine the location of the objects. The purpose of this study was to develop a radiopaque dental acrylic resin, which has clinically detectible radiopacity with minimal change of mechanical properties and color. The radiopacity, color change(CIE 6..E) and microhardness of acrylic resins were determined after mixing barium sulfate or iodide compound. Thermocycling course was conducted to determine the change of characteristic of resins after using for a long time in the mouth. Five or ten percent of barium sulfate to total weight of cured material was mixed with heat curing dental acrylic resin or chemically curing orthodontic resin. In the case of iodide compound, the mixing ratio was two or three percent. After mixing the high radiopaque materials, resin was cured to 20×20×2 mm plate, polished with #600 sand paper and finally polished with Microcloth(Buehler). The specimens were thermocycled in 5 and 55 t distilled water for 2,000 times, and the measurement of radiopacity, color and Vickers hardness was repeated every 500 times thcrmocycling. The radiopacity of specimens on the X -ray films was measured with densitometer(X-rite). The color change was detennined with differential colorimeter(Model TC-6FX, Tokyo Denshoku), and the Vickers hardness number was measured with microhardness tester(Mitsuzawa). The following results were obtained : 1. All the three variables, the kinds of acrylic resins, the mixing or the kinds of high radiopaque materials and thermocycling, had combined effect on the radiopacity of the dental acrylic resins(p<0.0l). 2. The two variables, the mixing or the kinds of high radiopaque materials and thermocycling, influenced on the radiopacity of the dental acrylic resins(p<0.01). But the kinds of acrylic resins did not influence on the color change of mixed dental acrylic resins(p>0.05). 3. Each of the three variables, the kinds of acrylic resins, the mixing or the kinds of high radiopaque materials and thermocycling, influenced on the radiopacity of dental acrylic resins(p<0.0l). 4. The high radiopaque materials used in this study did not yield clinically usable radiopacity, and the color change was great after mixing those materials.

• KSBB Journal
• /
• 제16권1호
• /
• pp.82-86
• /
• 2001

Glyco-acrylate and methacrylate were synthesized by lipase-catalyzed glycosylation of acrylic acid, methacrylic acid and their vinyl esters with $\beta$-methyl fructoside and glycerol in t-butanol as a reaction medium. At the optimum conditions for enzymatic glycosylation of acrylic acid and vinyl methacrylate, we attained up to 80% conversion for glyco-acrylate from acrylic acid and 90% conversion for glyco-methacrylate from vinyl methacrylate. The polymerizable glyco-acrylates and methacrylate have biomedical application as hydrophilic monomers and hydration modifiers to be use for hydrogel contact lens formulation.

• Korean Chemical Engineering Research
• /
• 제55권5호
• /
• pp.586-592
• /
• 2017

본 연구에서는 n-butyl acrylate (BA), methyl methacrylate (MMA), 2-hydroxypropyl methacrylate (HPMA) 및 acetoacetoxyethyl methacrylate(AAEM) 단량체를 부가 중합시켜 고형분이 75%인 아크릴수지를 합성하였다. 이때, 아크릴수지의 유리전이온도($T_g$)를 20, 30, $40^{\circ}C$로, 수산기가(OH value)를 60, 90, 120으로 변화시켰다. 그 결과, 아크릴수지의 점성도는 $T_g$와 수산기가가 증가할수록 증가하였다. 합성된 아크릴수지는 높은 가교밀도를 갖도록 설계되어 고탄력성과 고내구성을 유지하였다. 가교된 아크릴수지는 블록이소시아네이트(Desmodur BL-3175)와 경화 반응시켜 아크릴 우레탄 투명 도료를 제조하는데 사용되었다. 도료에 대하여 점성도, 접착성, 연필경도 및 $60^{\circ}$ 경면광택도 등의 측정을 통해 물리적 특성을 분석하였고, 아크릴 우레탄 투명 도료는 코일코팅용 상도 도료로서 적용되기 위하여 시편으로 제조되어 다양한 특성이 평가되었다. 제조된 도료는 접착력이 뛰어났고, $60^{\circ}$ 경면광택도와 연필경도에서 우수한 특성을 나타내었으며, 환경 친화적이었다.

• 대한치과보철학회지
• /
• 제42권4호
• /
• pp.373-385
• /
• 2004

Statement of problem: The microbial adhesion on the surface of materials used in prosthodontics and restorative dentistry significantly influences microbial infection. Purpose: The purpose of this study was to evaluate the effect of how the degree of surface roughness of acrlyic resin affect the adhesion of bacteria. Material and methods: Resins were finished with $50{\mu}m$ and $250{\mu}m$ aluminium oxide particles by using sandblaster, by using stone point, and high polished with $Opa^{(R)}$ and Lace $motor^{(R)}$. The surface of acrylic resin attached by bacteria was directly touched on the surface of BHI agar, which was incubated. Bacteria colonies formed on BHI agar were counted in accordance with the degree of the surface roughness. Results: 1. The viable cell number of Streptococcus mutans increased on the acrylic resins incubated in BHI broth than in PBS. 2. The viable cell number of Streptococcus mutans increased on the acrylic resins incubated without agitation than with agitation, washed three times than six times, and incubated in broth added with 5% sucrose than without sucrose. 3. When Streptococcus mutans incubated in BHI broth, the number of Streptococcus mutans colonies formed on BHI agar was the largest on the acrylic resins finished with $250{\mu}m$ aluminium oxide particle using sandblaster. But when incubated in BHI broth containing sucrose, the number of colonies formed on that was the largest on the acrylic resins high polished using $Opal^{(R)}$ and Lace $motor^{(R)}$. 4. When Streptococcus sanguis was incubated in BHI broth with or without sucrose, the number of Streptococcus mutans colonies formed on BHI agar was the largest on the acrylic resins finished with $250{\mu}m$ aluminium oxide particle using sandblaster. 5. When Actinomyces viscosus was incubated in BHI broth with or without sucrose, the number of Streptococcus mutans colonies formed on BHI agar was the largest on the acrylic resins high polished using $Opal^{(R)}$ and Lace $motor^{(R)}$. Conclusion: These results indicated that when acrylic resins attached by bacteria were touched on the surface of BHI agar, the number of bacterial colonies formed on the agar was dependent on the bacterial species. Also, the result of this study was showed that increase in the surface roughness and the addition of sucrose increased retention of microbial cells.