• 보존과학회지
• /
• 제30권3호
• /
• pp.287-298
• /
• 2014

이 연구에서는 무령왕릉에 사용된 전돌의 재료 특성에 관하여 고찰하였다. 압축 강도, 열전도도, 흡수율 등의 재료 특성은 비파괴 실험으로 측정하였다. 그 중에서 무령왕릉 전돌의 압축강도는 초음파 측정법과 흡수율을 이용하여 추정하였다. 실험 결과, 초음파 속도를 이용한 압축강도는 표면이 고르지 못하고 두께 편차가 큰 문화재 시편 특성상 표준편차가 크게 나타났다. 그러나 흡수율을 적용한 압축강도 값 (28.69 MPa ~ 33.19 MPa)은 일반 콘크리트의 압축강도 수준으로 편차가 낮게 나타났다. 따라서 초음파 속도를 이용하는 방법보다 흡수율을 이용하는 방법이 무령왕릉 전돌의 압축강도 예측법으로 보다 적합한 것으로 판단된다. 무령왕릉 전돌의 열전도도는 시료의 표면상태와 두께에 영향을 받지 않는 Mathis TCi를 이용하여 측정하였으며, 평균 1.58 W/mK로 흙에 근접한 값을 지닌다. 무령왕릉 전돌의 흡수율과 수분 잔류율은 각각 1.6 % ~ 15 %, 0 % ~ 0.7 %의 범위를 나타냈다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.87-88
• /
• 2011

High absorptance of lightweight aggregate make a hard product, work, quality management ect. for making low absorptance property, lightweight aggregate is coated by an organic matter and that way remarkably showed to decrease the absorptance by pre-study. but first, we would need a check to fit into the concrete which both fresh concrete and hardened concrete. In this study, mechanical property change of coated lightweight aggregate concrete was analysed by compared experiment with coated lightweight aggregate concrete and non-coated aggregate concrete.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.13-16
• /
• 2008

This paper is to present the performance data for improved direct setting method using tile bond for application of porcelain tile under 1 percent absorptance. For this purpose, improved direct setting method type 1 & 2(tile bond curing time 0, 24H) were compared with the conventional setting methods(including direct setting method and improved pressure setting method) in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion, heat ageing(70℃) and freeze-thaw cycle. On the basis of test results, the adhesive strength of direct setting method was lowest for the conventional setting methods. But improved direct setting method using tile bonds(A, B) came close to the result of improved pressure setting method using tile bonds.

• KIEAE Journal
• /
• 제6권4호
• /
• pp.33-39
• /
• 2006

This study aims to investigate the method to reduce the surface temperature caused by insolation. To achieve this goal, surface temperature of building is measured and the effects of exterior material's color and brilliance were checked with infrared imaging. And also, exterior material's absorptances due to outdoor surface heat transfer coefficients were measured. After surface temperature measurement of 37 specimen of 5 categories, the temperature is the highest on wood($53.62^{\circ}C$) and panel($52.05^{\circ}C$). Dryvit, stone, brick is the rating of order. For exterior material's absorptances, panel(0.883) and wood(0.868) were high and Dryvit, stone, brick follows wood and panel.

• 대한기계학회논문집B
• /
• 제29권11호
• /
• pp.1257-1264
• /
• 2005

An inverse problem to determine two-dimensional total heat exchange factor is studied for the prediction of the slab temperature in the reheating furnace. Temperature measurements by the experiment are used in the inverse analysis. This inverse analysis employs the conjugate gradient method. The overall heat absorptances for 12-zones of the cross-section of the slab are estimated. The estimated temperatures at measurement locations are in good agreements with the measured temperatures.

• Current Optics and Photonics
• /
• 제5권4호
• /
• pp.375-383
• /
• 2021

We present a simulation method to design antireflection coating (ARCs) for fiber-coupled superconducting nanowire single-photon detectors. Using a finite-element method, the absorptance of the nanowire is calculated for a defined unit-cell structure consisting of a fiber, ARC layer, nanowire absorber, distributed Bragg reflector (DBR) mirror, and air gap. We develop a method to evaluate the uncertainty in absorptance due to the uncontrollable parameter of air-gap distance. The validity of the simulation method is tested by comparison to an experimental realization for a case of single-layer ARC, which results in good agreement. We show finally a double-layer ARC design optimized for a system detection efficiency of higher than 95%, with a reduced uncertainty due to the air-gap distance.

• 한국전기전자재료학회논문지
• /
• 제27권9호
• /
• pp.589-593
• /
• 2014

AlNO multi-layer thin films on aluminum substrates were prepared by DC reactive magnetron sputtering method. $Al_2O_3$/AlNO(LMVF)/AlNO(HMVF)/Al/substrate of 4 multi-layer has been prepared in an Ar and ($N_2+O_2$) gas mixture, and $Al_2O_3$ of top layer is anti-reflection layer on double AlNO(LMVF)/AlNO(HMVF) layers and Al metal of infrared reflection layer. In this study, the roughness and surface properties of AlNO thin films were estimated by field emission scanning electron microscopy(FE-SEM). The grain size of AlNO thin films increased with increasing sputtering power. The composition of thin films has been systematically investigated using electron probe microanalysis(EPMA). The optical properties with wavelength spectrum were recorded by UV-Vis-NIR spectrophotometry at a range of 200~1,500 nm. The absorptance of AlNO films shows the increasing trend with swelling ($N_2+O_2$) gas mixture in HMVF and LMVF deposition. The excellent optical performance showed above 98% of absorptance in visible wavelength region.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1105-1111
• /
• 2011

본 연구의 목적은 Nd:YAG 펄스레이저 조사 후 알루미늄 합금 6061-T6 시편의 표면상태에 대한 표면 거칠기의 영향을 연구하는 것이다. 초기 표면 거칠기를 다르게 하기 위해 다아이몬드 입자($1{\mu}m$)와 연마지(#100, #220, #600, #2400)를 이용하여 표면을 가공하였다. 10 번의 펄스레이저를 조사한 후 주사전자현미경과 광학현미경 그리고 원자현미경을 이용하여 표면상태를 관찰하였다. 그 결과 표면 거칠기가 증가할수록 용융부의 지름이 증가하였는데, 이는 표면 거칠기에 따라 표면부에서 레이저 빔의 다중반사와 다중흡수가 일어나 레이저 빔의 흡수율이 변하기 때문이다. 이를 검증하기 위해 용융부의 지름으로부터 표면 거칠기에 의해 증가하는 상대적인 흡수율을 계산하였으며 평균 표면 거칠기가 증가함에 따라 상대적인 흡수율이 용융부의 지름과 유사한 형태로 증가하는 것을 보였다.

• 한국태양에너지학회 논문집
• /
• 제33권3호
• /
• pp.27-35
• /
• 2013

One of the most important factors that have a large influence on performance of the solar water heater system is performance of the solar collector, more detailedly, coating technology on the surface of the solar collector, which can provide high solar absorptance and low emittance. The core of the coating technology is to coat solar selective surfaces. In this study, various performance experiments are carried out using $Cr_2(SO_4)_3{\cdot}15H_2O$ coating technology. Here, IGBT(Insulated Gate Bipolar Transistor) of 5000A-15V was used as the surface processing rectifier which can stably output power and also can control voltage and current. The plating solution mainly contains black chrome$^{+3}$ concentration, H-y Conductivity, N-u Complex, NF Additive and NC-2 Wetter. Before applying the black chrome coating on the copper plate, optimal conditions are provided by using various preprocessing methods such as removal of fat, activation, electrolytic polishing, nickel strike, copper sulfate plating and bright neckel plating, and then the automatic continuous coating experiment are performed according to plating time and cathode current density. In the experiment, after the removal of fat, chemical polishing, nickel strike and activation processes as the preprocessing methods, the black chrome coating was performed in a plate solution temperature of $28^{\circ}C$ and a cathode current density of $18A/cm^2$ for 90 seconds. The thickness of chrome and nickel on the coated plate is $0.389{\mu}m$, $159{\mu}m$ respectively. As a result of the coating experiment, it showed the most excellent performance having a high solar absorptance of 98% and a low emittance of $5{\pm}1%$ when the black chrome surface had a thickness of $0.398{\mu}m$.

• 마이크로전자및패키징학회지
• /
• 제29권1호
• /
• pp.55-59
• /
• 2022

본 논문에서는 플라즈몬 공명 현상을 통하여 나노 입자 주변의 전기장을 증폭시키며, 흡광률을 높일 수 있는 구조를 시간영역 유한차분(FDTD)시뮬레이션을 이용하여 나노입자를 평면에 배열하였을 때와 비교하여 나노 구조에 배열하였을 때의 전기장과 흡광도를 비교하였다. 또한 나노구조의 폭을 240 nm ~ 300 nm로 조절하여 입자간의 간격이 좁을수록 광 흡수율이 높음을 보이고자 하였다. 또한 UV 임프린트를 통하여 나노 입자와 나노 구조를 표면에 함께 형성시키는 방법에 대한 연구를 진행하였다. 해당 구조에 입자를 형성하기 위하여 스프레이 코팅을 이용하여 나노 입자를 구조 제작에 사용되는 몰드에 먼저 배열한 후, UV 임프린팅을 통해 제작하였고 나노구조와 입자가 함께 형성됨을 Scanning Electron Microscopy 로 확인하였다.