• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.9
• /
• pp.52-59
• /
• 2014

The aims of this paper are to characterize the transient overvoltages(TOVs) and to evaluate the risk occurring at 22.9kV consumer's substation. The measurements of lightning- and switching-caused TOVs were made during Mar. 2013 and Feb. 2014. As a consequence, 47 events of TOVs were recorded and 4 of them were higher than the input voltage envelope(IVE) of the information technology industry council(ITI) curve. The measured TOVs are characterized by longer front times and longer durations compared to the $1.2/50{\mu}s$ standard impulse voltage waveform, and some of them represent bipolar waves with lower oscillation frequencies. It suggests that the test of non-standard impulse voltage waveforms is needed for effective risk assessments of power apparatus. Lightning- and switching-caused TOVs exceeding IVE of ITI curve are induced at the secondary of 22.9kV potential transformer(PT). We may, therefore, conclude that the surge protection devices should be applied at the secondary of PT and the surge absorbers should be installed at the primary of VCB or PT. The results presented in this paper could be useful to design the reasonable insulation coordination for 22.9kV consumer's substation.

• Journal of Navigation and Port Research
• /
• v.34 no.7
• /
• pp.539-542
• /
• 2010

In this paper, we designed and fabricated the Electro-Magnetic (EM) wave absorber for wireless LAN by using Amorphous and CPE. The material constants and the absorption properties were measured for the samples containing 50 %, 60 %, and 70 % weight fraction of Amorphous. Moreover, the EM wave absorption abilities were simulated for the EM absorbers in different thicknesses by adopting the measured permittivity and permeability, and then the EM wave absorber was fabricated based on the simulated design values. As a result, the EM wave absorber with the composition ratio in Amorphous : CPE = 60 : 40 wt.% with the thickness of 4 mm has the absorption ability more than 35 dB at 2.4 GHz. Thus, it is expected the wireless LAN environment can be improved by using the developed absorber.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.3
• /
• pp.285-290
• /
• 2008

Pyrotechnic shock or pyroshock is characterized as a transient vibration phenomena which shows large acceleration and high frequency range up to 10kHz during the operation of separation devices where explosives are used. During the flight of a launch vehicle, pyro-shock is mainly generated at several events such as satellite separation, fairing separation and stage separation. In this paper, characteristics of pyroshock are introduced briefly, and PEEK washer shock absorber is applied for the reduction of pyroshock in the high frequency range. With some electronic devices, reduction characteristic of pyroshock using washer type shock absorber are studied. Random vibration tests are also performed for the verification of vibrational characteristics.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.2
• /
• pp.171-178
• /
• 2009

A comparative analysis of the hindered amine light stabilizers (HALS) and UV abosrber (UVA) and their respective photostabilizing effect on wood plastic composites (WPCs) are reported in this study. The influence of accelerated weathering on the mechanical properties of the composites and the microscopic morphology of a degraded layer on the cross section and the surface were studied. UV absorbers were more efficient at preventing composite lightening than was UV stabilizer. The amount of whitening decreased with the increase of photostabilizers. With the addition of a UV absorber (Tinuvin360), the tensile modulus and strength of the composites increased slightly. However, the addition of a light stabilizer (Tinuvin770) and a UV absorber decreased the tensile modulus and strength of the composites. After 250 and 500 hr exposure, tensile modulus and strength of the un stabilized and stabilized composites decreased. The tensile strength of UV absorber (Chimassorb81)-stabilized composites was significantly greater than that of control and light stabilizer (Tinuvin770)- and UV absorber (Tinuvin360)-stabilized composites. UV absorber-stabilized samples showed less whitening and photodegradation than control and light stabilizer-stabilized samples.

• Wind and Structures
• /
• v.14 no.2
• /
• pp.113-131
• /
• 2011

Excessive wind-induced motion in tall buildings can cause discomfort, affect health, and disrupt the daily activities of the occupants of a building. Dynamic vibration absorbers such as the tuned mass dampers (TMDs) can be used to reduce the wind-induced motion below a specified tolerable serviceability limit state (SLS) criterion. This study investigates whether the same probability of not exceeding specified wind-induced motion levels can be achieved by torsionally sensitive structures without/with linear/nonlinear TMDs subjected to partially correlated wind forces, if they are designed to just meet the same SLS criterion. For the analyses, different structures and the uncertainty in the response, wind load and perception of motion is considered. Numerical results indicate that for structures that are designed or retrofitted without or with optimum linear TMDs and satisfying the same SLS criterion, their probability of exceeding the considered criterion is very consistent, if the inherent correlation between the wind forces is considered in design. However, this consistency deteriorates if nonlinear TMDs are employed. Furthermore, if the correlation is ignored in the design, in many cases a slightly unconservative design, as compared to the designed by considering correlation, is achieved.

• Structural Engineering and Mechanics
• /
• v.32 no.4
• /
• pp.517-529
• /
• 2009

A passive vibration mitigation architecture is proposed to damp transverse vibrations of guyed masts. The scheme is based on a number of pendula attached to the mast and tuned to the vibration modes to be controlled. This scheme differs from the well-known autoparametric pendulum absorber system. The equations of motion of the guyed mast with an arbitrary number of pendula are obtained. The leading bending behaviour of a typical truss mast is described by an equivalent beam model whereas the guys are conveniently modeled as equivalent transverse springs whose stiffness comprises the elastic and geometric stiffness. By assuming a mast with an inertially and elastically isotropic cross-section, a planar model of the guyed mast is investigated. The linearization of the equations of motion of the mast subject to a harmonic distributed force leads to the transfer functions of the structure without the dampers and with the dampers. The transfer functions allow to investigate the mitigation effects of the pendula. By employing one pendulum only, tuned to the frequency of the lowest mode, the effectiveness of the passive vibration potential in reducing the motion and acceleration of the top section of the mast is demonstrated.

• Structural Engineering and Mechanics
• /
• v.66 no.6
• /
• pp.713-727
• /
• 2018

Thin-walled mental tubes under lateral crushing are desirable and reliable energy absorbers against impact or blast loads. However, the early formations of plastic hinges in the thin cylindrical wall limit the energy absorption performance. This study investigates the energy absorption performance of a simple, light and efficient energy absorber called the ring stiffened tube. Due to the increase of section modulus of tube wall and the restraining effect of the T-stiffener flange, key energy absorption parameters (peak crushing force, energy absorption and specific energy absorption) have been significantly improved against the empty tube. Its potential application in the offshore blast wall design has also been investigated. It is proposed to replace the blast wall endplates at the supports with the energy absorption devices that are made up of the ring stiffened tubes and springs. An analytical model based on beam vibration theory and virtual work theory, in which the boundary conditions at each support are simplified as a translational spring and a rotational spring, has been developed to evaluate the blast mitigation effect of the proposed design scheme. Finite element method has been applied to validate the analytical model. Comparisons of key design criterions such as panel deflection and energy absorption against the traditional design demonstrate the effectiveness of the proposed design in blast alleviation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1993.11a
• /
• pp.144-148
• /
• 1993

This paper is a study on electromagnetic wave absorption properties for the composition ratio of Ni-Zn-Fe$_2$O$_4$. Li-Zn-Fe$_2$O$_4$was composed of Fe$_2$O$_3$ 48∼51mo1%, LiO 18 ∼22mo1%, ZnO 34∼27mo1%. and sintering was carried out at 1200$^{\circ}C$. Through the experiments, the resonance phenomenon occured at low frequence range for high permeability, and vice versa. Specialy, In the case of Fe$_2$O$_3$49mol%, NiO 20mo1%, ZnO 3lmol% ,and the matching thickness was 10mm , the absorbing bandwith was 0.35 ∼0.95GHz. Also, In the case of Fe$_2$O$_3$51mo1%. NiO 22mo1%, ZnO 27mol%, we could get the absorbing bandwith of 0.45∼1.2GHz when the matching thickness was 6mm. Therefore. it is proved that electromagnetic wave absorbers with the above bandwidth range can be fabricated successful1y.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.5
• /
• pp.264-267
• /
• 2015

AlCrNO cermet films were prepared on aluminum substrates using a DC-reactive magnetron sputtering method and a water-cooled Al:Cr target. The Al₂O₃/AlCrNO (LMVF)/AlCrNO (MMVF)/AlCrNO (HMVF)/Al/substrate of the 5 multi-layers was prepared according to the Ar and (N₂ + O₂) gas-mixture rates. The Al₂O₃ of the top layer is the anti-reflection layer of triple AlCrNO (LMVF)/AlCrNO (MMVF)/AlCrNO (HMVF) layers, and an Al metal forms the infrared reflection layer. In this study, the crystallinity and surface properties of the AlCrNO thin films were estimated using X-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM), while the composition of the thin films was systematically investigated using Auger electron spectroscopy (AES). The optical properties of the wavelength spectrum were recorded using UH4150 spectrophotometry (UV-Vis-NIR) at a range of 0.3 μm to 2.5 μm.

• Korean Journal of Materials Research
• /
• v.12 no.6
• /
• pp.458-463
• /
• 2002

Carbon nanotubes were synthesized at various conditions using Ni-catalytic thermal chemical vapor deposition method and their characteristic properties were investigated by SEM, TEM and Raman spectroscopy. Carbon nanotubes were formed on very fine Ni-catalytic particles. The carbon nanotubes synthesized by thermal decomposition of acetylene at $700^{\circ}C$ had a coiled shape, while those synthesized at $850^{\circ}C$ showed a curved and Y-shape having a bamboo-like morphology. It was found that the carbon nanotube was also made on the fine Ni-catalytic particles formed on the surface of 100~400nm sized large ones after pretreatment with $NH_3$.ber composites show the high dielectric constant and large conduction loss which is increased with anisotropy of fiber arrangement. It is, therefore, proposed that the glass and carbon fiber composites can be used as the impedance transformer (surface layer) and microwave reflector, respectively. By inserting the foam core or honeycomb core (which can be treated as an air layer) between glass and carbon fiber composites, microwave absorption above 10 dB (90% absorbance) in 4-12 GHz can be obtained. The proposed fiber composites laminates with sandwitch structure have high potential as lightweight and high strength microwave absorbers.