• Journal of the Semiconductor & Display Technology
• /
• v.11 no.2
• /
• pp.7-11
• /
• 2012

SiNx films have been wildly used as anti-reflection coatings and passivation for crystalline silicon solar cells. In this study, the SiNx films were deposited by using high frequency (13.56MHz) PECVD and optical & passivation properties were investigated. The RF power was changed in a certain range for the film deposition. Then, the refractive index, etch rate, minority carrier lifetime and cell efficiency were measured to study the properties of the film respectively. The optimal deposition conditions for application to crystalline silicon solar cells were proposed as results of the study. Finally, the best cell efficiency of 16.98% was obtained from the solar cell with the SiNx films deposited by RF power of 550W.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.183-186
• /
• 1990

The lattice mismatch between ZnS and Si is negligible because of its value being 0.39%. In this study, $ZnS/_{(P)}Si$ solar cell were fabricated as a layer of ZnS is epitaxially grown on a silicon substrate by PVD method and its photovoltaic properties were measured and discussed. The heat treatment was done after deposition. As the temperature increased up to a certain value, the film has better perfection in crystal structure and electrical characteristics. Measurments of the change that occur in the ZnS films were made by SEM., X-ray diffraction. The optimal thickness of film showned $0.6{\mu}m$, being measured by SEM. The great improvement of the grain growth ZnS film came out after heat-treatment. The result obtained from the $ZnS/_{(P)}Si$ solar cell as follows:short circuit current; $I_{sc}=54mA/cm^2$,open voltage; $V_{oc}=400mV$, fill factor FF=0.72, conversion efficiency; ${\eta}=15.6%$ under the irradiation of 100 ($mW/cm^2$) focused by solar energy. And these are discussed in comparison with other kinds.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.3
• /
• pp.185-190
• /
• 2018

Dopant-free silicon heterojunction solar cells using Transition Metal Oxide(TMO) such as Molybdenum Oxide($MoO_X$) and Vanadium Oxide($V_2O_X$) have been focused on to increase the work function of TMO in order to maximize the work function difference between TMO and n-Si for a high-efficiency solar cell. One another way to increase the work function difference is to control the silicon wafer resistivity. In this paper, dopant-free silicon heterojunction solar cells were fabricated using the wafer with the various resistivity and analyzed to understand the effect of n-Si work function. As a result, it is shown that the high passivation and junction quality when $V_2O_X$ deposited on the wafer with low work function compared to the high work function wafer, inducing the increase of higher collection probability, especially at long wavelength region. the solar cell efficiency of 15.28% was measured in low work function wafer, which is 34% higher value than the high work function solar cells.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1325-1327
• /
• 2002

$ITO_{(n)}/Si_{(p)}$ solar cell was fabricated by vaccum deposition method under the resistance heating with substrate temperature kept about 200[$^{\circ}C$] and than their properties are investigated. The cell charateristics can be improved by annealing but are deteriorated at temperature above 650[$^{\circ}C$] for longer than 15[min].

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.2
• /
• pp.33-37
• /
• 2003

The new textured surface epitaxial base(TSEB) cell as a high efficiency Si solar cell was fabricated and its eletro-optical characteristics were investigated. The fabricated device showed the open circuit voltage of 0.62 V, the short circuit current of 40 mA, the fill factor of 0.7, and the efficiency of 16% under the incident light of AM-1 100 mW/$cm^2$. The TSEB cell proposed in this paper has the structural superiority in the fabrication of high efficiency solar cell due to the carrier drift transport in the optical absorption region and the formation of back surface field by $P^-/P^+$ epitaxial base, and the low emitter series resistance by insertion of $n^+$ buried contact.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.3
• /
• pp.301-306
• /
• 2016

The effects of nanotexturing and post-etching on the reflection and quantum efficiency properties of diamond wire sawn (DWS) multicrystalline silicon (mc-Si) solar cell have been investigated. The chemical solutions, which are acidic etching solution (HF-$HNO_3$), metal assisted chemical etching (MAC etch) solutions ($AgNO_3$-HF-DI, HF-$H_2O_2$-DI) and post-etching solution (diluted KOH at $80^{\circ}C$), were used for micro- and nano-texturing at the surface of diamond wire sawn (DWS) mc-Si wafer. Experiments were performed with various post-etching time conditions in order to determine the optimized etching condition for solar cell. The reflectance of mc-Si wafer texturing with acidic etching solution showed a very high reflectance value of about 30% (w/o anti-reflection coating), which indicates the insufficient light absorption for solar cell. The formation of nano-texture on the surface of mc-Si contributed to the enhancement of light absorption. Also, post-etching time condition of 240 s was found adequate to the nano-texturing of mc-Si due to its high external quantum efficiency of about 30% at short wavelengths and high short circuit current density ($J_{sc}$) of $35.4mA/cm^2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.766-772
• /
• 2011

Amorphous Si (a-Si) thin films of $p^+/p^-/n^+$ were deposited on $Si_3N_4$/glass substrate by using a plasma enhanced chemical vapor deposition (PECVD) method. These films were annealed at various temperatures and for various times by using a rapid thermal process (RTP) equipment. This step was added before the main thermal treatment to make the nuclei in the a-Si thin film for reducing the process time of the crystallization. The main heat treatment for the crystallization was performed at the same condition of $600^{\circ}C$/18 h in conventional furnace. The open-circuit voltages ($V_{oc}$) were remained about 450 mV up to the nucleation condition of 16min in the nucleation RTP temperature of $680^{\circ}C$. It meat that the process time for the crystallization step could be reduced by adding the nucleation step without decreasing the electrical property of the thin film Si for the solar cell application.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.3
• /
• pp.139-143
• /
• 2017

N-type crystalline silicon solar cells have high metal impurity tolerance and higher minority carrier lifetime that increases conversion efficiency. However, junction quality between the boron diffused layer and the n-type substrate is more important for increased efficiency. In this paper, the current status and prospects for boron diffused layers in N-type crystalline silicon solar cell applications are described. Boron diffused layer formation methods (thermal diffusion and co-diffusion using $a-SiO_X:B$), boron rich layer (BRL) and boron silicate glass (BSG) reactions, and analysis of the effects to improve junction characteristics are discussed. In-situ oxidation is performed to remove the boron rich layer. The oxidation process after diffusion shows a lower B-O peak than before the Oxidation process was changed into $SiO_2$ phase by FTIR and BRL. The $a-SiO_X:B$ layer is deposited by PECVD using $SiH_4$, $B_2H_6$, $H_2$, $CO_2$ gases in N-type wafer and annealed by thermal tube furnace for performing the P+ layer. MCLT (minority carrier lifetime) is improved by increasing $SiH_4$ and $B_2H_6$. When $a-SiO_X:B$ is removed, the Si-O peak decreases and the B-H peak declines a little, but MCLT is improved by hydrogen passivated inactive boron atoms. In this paper, we focused on the boron emitter for N-type crystalline solar cells.

• Journal of the Optical Society of Korea
• /
• v.18 no.2
• /
• pp.180-183
• /
• 2014

The surface of semiconductor solar cells, such as a-Si or CIGS (CuInGaSe) solar cells is not flat but textured in the microscopic domain. With textured surfaces, the optical reflectivity of a solar cell is different from that of flat surfaces in the wavelength region. In this paper, the effects of a textured surface on a CIGS solar cell are presented by RCWA (Rigorous Coupled Wave Analysis) method. The effect of incoherent light is also considered by RCWA with a Fourier analysis while conventional optical simulation uses the input light on the solar cell as coherent light. Using experimental results, the author showed that the RCWA method with a Fourier analysis is a proper method to simulate the optical properties of CIGS solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.492-492
• /
• 2014

On account of the good conductivity and optical properties, TCO is generally used in silicon heterojunction solar cell since the emitter material, hydrogenated amorphous silicon (a-Si:H), of the solar cell has low conductivity compare to the emitter of crystalline silicon solar cell. However, the work function mismatch between TCO layer and emitter leads to band-offset and interfere the injection of photo-generated carriers. In this study, work function engineering of TCO by oxygen reactive sputtering method was carried out to identify the trend of band-offset change. The open circuit voltage and short circuit current are noticeably changed by work function that effected from variation of oxygen ratio.