• 열처리공학회지
• /
• 제30권2호
• /
• pp.53-60
• /
• 2017

The aim of this study is to examine a feasibility to substitute Ti for Ta in reduced activation ferritic/martensitic (RAFM) steel by comparing a Ti-added RAFM steel with a conventional Ta-added RAFM steel. The microstructures and mechanical properties of Ta-, and Ti-added RAFM steels were investigated and a relationship between microstructures and mechanical properties was considered based on quantitative analysis of precipitates in two RAFM steels. Ta-, and Ti-added RAFM steels were normalized at $1000{\sim}1040^{\circ}C$ for 30 min and tempered at $750^{\circ}C$ for 2 hr. Both RAFM steels had very similar microstructures, that is, typical tempered martensite with relatively coarse $M_{23}C_6$ carbides at boundaries of grain and lath, and fine MX precipitates inside laths. The MX precipitates were identified as TaC in Ta-added RAFM steel and TiC or (Ti, W)C in Ti-added RAFM steel, respectively. It is believed that these RAFM steels show similar tensile and Charpy impact properties due to similar microstructures. Precipitate hardening and brittle fracture strength calculated with quantitative analysis of precipitates elucidated well the similar behaviors on the tensile and Charpy impact properties of Ta-, and Ti-added RAFM steels.

• 한국전기전자재료학회논문지
• /
• 제17권2호
• /
• pp.150-155
• /
• 2004

This study attempts to form a TiN barrier layer against Cu diffusion by the easier and more convenient method. In this new approach, Ti was sputter-deposited, and nitrided by heat-treating in the NH$_3$ambient. Sheet resistance of as-deposited Ti was 20 Ω/$\square$, but increased to 195 Ω/$\square$ after the heat-treatment at 30$0^{\circ}C$, and lowered to 120 Ω/$\square$ after the heat-treatment at 50$0^{\circ}C$, and $600^{\circ}C$. AES results for these thin films confirmed that the atomic ratio of Ti and N was close to 1:1 at or above 40$0^{\circ}C$ heat-treatment. However, it was also found that excessive oxygen was contained in the TiN layer. To examine the barrier property against Cu diffusion, 100nm Cu was deposited on the TiN layer and then annealed at 40$0^{\circ}C$ for 40 min.. Cu remained at the surface without diffusing into the Si layer.

• 한국재료학회지
• /
• 제12권12호
• /
• pp.904-910
• /
• 2002

Surface alloying using TiC, $TiB_2$ and VC ceramic particles on carbon steel has been performed using high voltage electron beam. Each type of ceramic particles was mixed with flux of Al and $MgF_2$ in 1 to 4 ratio. The microstructures of the surface alloyed layers consisted of melted region, interface region. heat affected region and the unaffected matrix. The surface layer of the TiC surface alloyed had a cubed primary and a eutectic type of TiC. $TiB_2$ in surface layer of $TiB_2$ surface alloyed were incompletely melted with$ TiB_2$ particles as observed before the alloying. On the surface layer of the VC surface alloyed, very well defined cell structure was observed with VC on the cell boundary. In addition, ~50 nm in diameter VC particles in high density were ubiquitous in the matrix. Those fine VC particles prominently improved the hardness and wear resistance of the surface layer of the VC surface alloyed.

• 한국세라믹학회지
• /
• 제36권8호
• /
• pp.835-842
• /
• 1999

본 연구에서는 Ag-Cu-Ti 와 Ag-Cu-In-Ti 를 사용하여 브레이징법으로 질화규소 간 접합체를 제작하고 $400^{\circ}C$와 $650^{\circ}C$에서 장시간(2000 h) 열처리 후 파괴 강도의 변화를 살펴보았다. 접합후 강도는 Ag-Cu-Ti 가 높게 나왔지만, 열처리 시간이 증가할수록 Ag-Cu-In-Ti 의 경우가 강도의 감소 정도가 작은 것으로 나타났다. 또한 고온 응용을 위해 개발된 새로운 접학 합금인 Au-Ni-Cr-Mo-Fe 계를 이용하여 질화 규소 간의 접합체를 제작하여 $650^{\circ}C$에서 100시간까지 장시간 열처리 하였다 접합 당시의 강도는 상용 접합 합금보다는 낮은 값을 보였지만, 열처리를 함에 따라 강도의 증가를 보였다 SUS316과의 접합시에는 중간재로 몰리브데늄 또는 구리를 사용하였으며 $400^{\circ}C$에서 1000시간 동안 열처리하였다. 강도는 몰리브데늄을 사용한 경우가 높게 나왔지만, 접합체의 형성이 어렵다는 단점이 있었다. 산화 실험에서는 Ti가 첨가된 접합 합금인 Ag-Cu-Ti 의 경우가 첨가되지 않은 Ag-Cu의 경우보다 산화가 잘 일어나며, 인듐을 첨가한 Ag-Cu-In-Ti 의 경우는 산화 억제의 효과가 나타났다. 전반적으로 In을 포함한 접합 합금이 고온 신뢰도 면에서 우수한 것으로 나타났다.

• 한국재료학회지
• /
• 제4권2호
• /
• pp.143-151
• /
• 1994

$(PbZr_{52},Ti_{48})O_{3}$인 composite ceramic target을 사용하여 R. F. 마그네트론 스퍼터링 방법으로 기판온도 $300^{\circ}C$에서 Pt/Ti/Si 기판위에 PZT 박막을 증착하였다. 페롭스 카이트 PZT박막을 얻기 위하여 PbO분위기에서 로열처리를 행하였다. 하부전극으로 Pt를 사용하였으며 Pt(205$\AA$)/Ti(500 $\AA$)/Si 및 Pt(1000$\AA$)/Ti(500$\AA$)/Si기판을 준비하여 Pt두께화 Ti층이 산소의sink로 작용함으로서 이를 가속화하였다. Ti층의 상부는 산소의 확산으로 인하여 TiOx층으로 변태하였고 하부는 in diffused Pt와 함께 실리사이드층을 형성하였다. TiOx 층의 형성은PZT층의 방향성에 영향을 주었다. 유전상수 (10kHz), 누설전류, 파괴전압, 잔류분극 및 항전계는 각각 571, 32,65$\mu A /\textrm{cm}^2$, 0.40MV/cm, 3.3$\mu C /\textrm{cm}^2$, 0.15MV/cm이었다.

• 한국세라믹학회지
• /
• 제33권5호
• /
• pp.536-546
• /
• 1996

The TiC-Ni/Al reaction-bonding composites were prepared by the infiltration of Ni/Al melt into the TiC preforms. The microstructure the reaction composition crystalline phase and the mechanical properties of the composites were investigated. During the reaction-bonding Ni/Al mixture had a good wettability and per-meability with TiC preform and pore-free and fully dense sintered bodies were produced. In the case of the Ni/Al atomic ratio of 0.3 and 0.5 TiC raw particle shape was changed to irregular particles because of the decomposition in the liquid matrix and its phenomena was more distinguished in the Al-rich liquid matrix. With increasing more than 1 of the Ni/Al atomic ratio the sample of TiC grain shape was changed from spherical to palatelet particles. Also with increasing the atomic ratio of Ni/Al bending strength and fracture spherical to palatelet particles. Also with increasing the atomic ratio of Ni/Al bending strength and fracture toughness were increased and its maximum value was 1073 MPa and 11 MPa.m1/2 respectively.

• 대한금속재료학회지
• /
• 제48권7호
• /
• pp.683-689
• /
• 2010

In this study, FeAl based intermetallic matrix composites reinforced with in-situ synthesized TiC particles were fabricated by an in-situ liquid mixing process. The microstructures, mechanical properties and fracture behaviors of the in-situ liquid mixing processed composite were investigated and compared with the vacuum suction casting processed composite. The results showed that the in-situ formed TiC particles exhibited fine and uniform dispersion in the liquid mixing processed composite, while significant grain boundary clustering and coarsening of TiC particles were obtained by the vacuum suction process. It was also shown in both types of composites that the hardness and bending strength were increased with the increase of the TiC volume fractions. Through the study of fractography in the bending test, it was considered that the TiC particles prohibited brittle intergranular fracture of FeAl intermetallic matrix by crack deflections. Because of the uniformly distributed fine TiC particles, the bending strength of the liquid mixing processed composite was superior to that of the casting processed composite.

• 한국분말재료학회지
• /
• 제11권2호
• /
• pp.165-170
• /
• 2004

Growth behavior of two different types of grains, faceted and rounded, in a liquid matrix has been studied in the (75WC-25TiCN)-30Co system. Powder samples were sintered above the eutectic temperature for various times under a carbon saturated condition. (Ti,W)(C,N) grains with a rounded shape and WC grains with a faceted shape coexisted in the same Co based liquid. With increasing sintering time, the average size of (Ti.W)(C,N) grains increased continuously and very large WC grains appeared. The growth of rounded (Ti,W)(C,N) grains followed a cubic law, r^3-r^3_0$=kt, where r is the average size of the grains, $r_0$ the initial average size, k the proportionality constant and t the sintering time. indicating a diffusion-controlled growth. On the other hand, the growth of the faceted WC grains resulted in a bimodal grain size distribution, showing an abnormal grain growth. These observations show that the growth behavior of different types of grains is governed by their shape, faceted or rounded, even in the same liquid matrix.

• 한국재료학회지
• /
• 제11권9호
• /
• pp.776-780
• /
• 2001

$SiO_2$ and polycrystalline Si layers were sequentially grown on (100) Si. NiSi was formed on this substrate from a 20nm Ni layer or a 20nm Ni/5nm Ti bilayer by rapid thermal annealing (RTA) at $300~500^{\circ}C$ to compare thermal stability. In addition, MOS capacitors were fabricated by depositing a 20nm Ni layer on the Poly-Si/$SiO_2$substrate, RTA at $400^{\circ}C$ to form NiSi, $BF_2$ or As implantation and finally drive- in annealing at $500~800^{\circ}C$ to evaluate electrical characteristics. When annealed at $400^{\circ}C$, NiSi made from both a Ni monolayer and a Ni/Ti bilayer showed excellent thermal stability. But NiSi made from a Ni/Ti bilayer was thermally unstable at $500^{\circ}C$. This was attributed to the formation of insignificantly small amount of NiSi due to suppressed Ni diffusion through the Ti layer. PMOS and NMOS capacitors made by using a Ni monolayer and the SADS(silicide as a dopant source) method showed good C-V characteristics, when drive-in annealed at $500^{\circ}C$ for 20sec., and$ 600^{\circ}C$ for 80sec. respectively.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2001년도 춘계학술대회 발표논문집
• /
• pp.91-94
• /
• 2001

Powder Metallurgy method have been used to fabricate TiC base composite with ferrous binder. TiC base composite has versatile hardness and is usable as sintered, or after heat treatment as required by the given applications. Smooth, round TiC grains impart high wear resistance and lubricity as well known characteristics of this composite. Annealed composite can be formed by conventional machining and be hardened up to 70 H$\_$R/C in vacuum. The optimizing fabrication process enables this composite to improve mechanical properties in heat, wear and corrosion environments. This study has examine the relationship between fabrication condition and mechanical property in TiC-Cr-Mo-Fe Composite.