• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.2
• /
• pp.129-136
• /
• 2002

A single-phase inverter using a diode bridge-type resonant circuit to implement ZVT(Zero Voltage Transition) switching is presented. It Is shown that the ZACE(Zero Average Current Error) algorithm based Polarized ramptime current control can provide a suitable interface between DC link of diode bridge-type resonant circuit and the inverter. The current control algorithm is analyzed about how to design the circuit with auxiliary switch which can ZVT operation for the main power switch. The simulation and experimental results would be shown to verify the proposed current algorithm, because the main Power switch is turn on with ZVT and the hi-directional inverter is operated.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.6
• /
• pp.547-555
• /
• 2013

This paper proposes the interleaved buck converter using a soft switching auxiliary circuit. In this scheme, an auxiliary circuit is added to the conventional interleaved buck converter and used to achieve soft-switching conditions for both the main switch and freewheeling diode. In addition, the switch in the auxiliary circuit operates under soft-switching conditions. Also, according to the input to output conditions, the main switch achieved zero-current-transition(ZCT) or zero-current & zero-voltage-transition(ZCZVT) at turn on. Thus, the proposed interleaved buck converter provides a higher efficiency. The basic operations, in this paper, are discussed and design guidelines are presented. The usefulness of the proposed converter is verified on a 200kHz, 180W prototype converter.

• Journal of Power Electronics
• /
• v.17 no.4
• /
• pp.892-904
• /
• 2017

A design of a Class-E inverter with only one inductor and one capacitor is presented. It is operated at the optimal operation mode for domestic cooker. The design principle is based on the zero-voltage derivative switching (ZVDS) of the Class-E inverter with a parallel load network, which is a parallel resonant equivalent circuit. An induction load characterization is obtained from a large-signal excitation test bench, which is the key to an accurate design of the induction cooker system. Consequently, the proposed scheme provides a more systematic, simple, accurate, and feasible solution than the conventional quasi-resonant inverter analysis based on series load network methodology. The derivative of the switch voltage is zero at the turn-on transition, and its absolute value is relatively small at the turn-off transition. Switching losses and noise are reduced. The parameters of the ZVDS Class-E inverter for the domestic induction cooker must be selected properly, and details of the design of the components of this Class-E inverter need to be addressed. A 1,200 W prototype is designed and evaluated to verify the validation of the proposed topology.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.1
• /
• pp.10-16
• /
• 2004

In this thesis, improved full wave mode ZVT(Zero-Voltage-Transition) PMW DC-DC Converters are presented to maximize the regeneration ratio of resonant energy by only putting an additional diode In series with the auxiliary switch. The operation of the auxiliary switch in a half wave mode makes it possible soft switching operation of all switches including the auxiliary switch whereas it is turned off with hard switching in conventional converter. The increase of the regeneration ratio to resonant energy results in low commutation losses and minimum voltage and current stresses. The operation principles of the improved ZVT PWM DC-DC Converters are theoretically analyzed using the boost converter topology as an example. Both theoretical analysis and experimental results verify the validity of the PWM boost converter topology with the improved full wave mode ZVT PWM converters.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.129-132
• /
• 2001

Recently, a ZVT boost converter is embedded in a power factor correction system. The control circuit of the converter assures soft-switching for all the MOSFETs and load regulation. The PFC system contains additional control circuits which assure the input voltage in a sinusoidal form and feed-forward line voltage regulation. In this paper, a soft switching boost converter with zero-voltage transition(ZVT) main switch using zero-current switching(ZCS) auxiliary switch is proposed. Operating intervals of the converter are persented and analyzed. The proposed results show that the main switch maintains UT while auxiliary switch retains ZCS for the complete specified line and load conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.5
• /
• pp.617-625
• /
• 1998

A passive energy recovery snubber for high-power-factor boost rectifier, in which the main switch is implemented with a MOSFET, is described in terms of the equivalent circuits that are operational during turn-on and turn-off sequences. These equivalent circuits are analyzed so that the overshoot voltage across the main switch, the snubber current, and the turn-off transition time can be predicted analytically. From these results, the normalized overshoot voltage is reduced to 1 as $_W2T_on$ varies from zero to $\pi$/2, and then it is fIxed at 1 for $_W2T_on$> $\pi$/2. The peak snubber inductor current is directly proportional to the input current. The turn-offtransition time wltoffvaries from 0 to 2.57, depending on $_W2T_on$. The main switch combined with proposed snubber can be turned on with zero current and turned off at limited voltage stress. The high-power-factor boost rectifier with proposed snubber is implemented, and the experimental results are presented to confirm the validity of proposed snubber.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.41-43
• /
• 1996

This paper describes on concerning electromagnetical and thermal behaviors during normal transition in Bi-2223/Ag superconducting multifilamentary tapes by conduction cooling. Some experiments were carried with operating temperature, 10-40K, and transport current as parameters in zero magnetic field. Sample tapes are transited normally with heater to intiate a quench. The voltage and temperature properties which accord to normal transition are measured by voltage taps and thermocouples attached to sample tapes, we also calculated longitudinal and transverse directions normal-zone propagation velocities from the voltage traces.

• Journal of Power Electronics
• /
• v.14 no.4
• /
• pp.661-670
• /
• 2014

A new DC/DC converter with zero voltage switching is proposed for applications with high input voltage and high load current. The proposed converter has two circuit modules that share load current and power rating. Interleaved pulse-width modulation (PWM) is adopted to generate switch control signals. Thus, ripple currents are reduced at the input and output sides. For high-voltage applications, each circuit module includes two half-bridge legs that are connected in series to reduce switch voltage rating to $V_{in}/2$. These legs are controlled with the use of asymmetric PWM. To reduce the current rating of rectifier diodes and share load current for high-load-current applications, two center-tapped rectifiers are adopted in each circuit module. The primary windings of two transformers are connected in series at the high voltage side to balance output inductor currents. Two series capacitors are adopted at the AC terminals of the two half-bridge legs to balance the two input capacitor voltages. The resonant behavior of the inductance and capacitance at the transition interval enable MOSFETs to be switched on under zero voltage switching. The circuit configuration, system characteristics, and design are discussed in detail. Experiments based on a laboratory prototype are conducted to verify the effectiveness of the proposed converter.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.9
• /
• pp.1597-1604
• /
• 2016

The speed at which the SRM (Switched Reluctance Motor) makes a transition from chopping control to single pulse operation. (i.e., low speed to high speed operation). It is unsatisfied with performance at all operational regimes. In this paper, the operational performance of SRM can be improved by using current hysteresis control method. This method maintains a generally flat current waveform. At the high speed, the current chopping capability is lost due to the development of the back-EMF. Therefore SRM operates in single pulse mode. By using zero-current switching and zero-voltage switching technique, the stress of power switches can be reduce in chopping mode. When the commutation from one phase winding to another phase winding, the current can be zero as fast as possible in this period because several times negative voltage of DC-source voltage produce in phase winding. This paper is compared to performance based on energy efficient C-dump converter topology and the proposed resonant C-dump converter topology. Simulation and experimental results are presented to verify the effectiveness of the proposed circuit.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.303-304
• /
• 2013

기술이 발전함에 따라 전력변환기의 소형화 고효율화가 요구되어지고, 이를 위해 고주파 스위칭 전력변환기가 필요로 하게 된다. 하지만 스위칭 주파수와 비례적으로 스위칭 손실이 증가하기 때문에 시스템의 효율이 감소한다. 이러한 문제를 해결하기 위해 DCM방식이나 공진을 이용한 ZVZCS(Zero-Voltage Zero-Currrent) 컨버터가 제안되고 있으나 소자의 정격용량이 커지는 단점을 갖는다. 또한 ZVT(Zero-Voltage Transition)를 포함한 소프트 스위칭 기법을 적용하는 다양한 컨버터가 제안되고 있으나 공진전류의 첨두에서 보조스위치가 스위칭을 하게 되어 보조스위치 스위칭 손실이 큰 단점이 있다. 본 논문에서는 변압기로 공진인덕터의 전압을 제한시켜 보조 스위치가 영전압/영전류 스위칭을 하게 함으로서 스위칭 손실을 발생시키지 않는 소프트 스위칭 구조를 제안한다.