• 한국전자파학회논문지
• /
• 제14권12호
• /
• pp.1248-1255
• /
• 2003

본 논문에서는 QPSK 방식을 채용하는 고속 무선 전송 시스템에 적용될 수 있는 Zero-Crossing IF-level QPSK 복조기에 대해서, 복조기에 소요되는 알고리즘들을 고찰하고 이를 구현하기 위한 H/W구조에 대해서 언급한다. Zero-Crossing IF-level QPSK 복조기를 구현하기 위해서, 비트 동기를 포착하는 심볼 동기부와 반송파 동기를 포착하는 반송파 동기부가 구현되어야 하는데, 심볼 동기부로는 Gardner 알고리즘을, 반송파 동기부로는 빠른 반송파 포착을 위한 Decision-Directed 동기화 알고리즘을 적용하여 설계, 구현하였다. 설계한 QPSK복조기를 Altera 사의 Design Compiler를 이용하여 CPLD-FLEX10K 칩에 합성해 본 결과 약 2.6 Mbps의 전송속도까지 복조 가능하였다. 설계된 Zero-Crossing IF-level QPSK 복조기를 ASIC으로 구현할 경우 CPLD속도의 5∼6 이상 고속화가 가능하므로 약 10 Mbps급 Zero-Crossing IF-level QPSK 복조가 가능하다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.564-570
• /
• 2010

Last train of the vehicle for eht energy saving and improved performance PWM converters ares widely used. In the case of PWM converters by the zero detection system performance depends on whether it can be argued. Zero voltage detectio method of the hardware and software approach is to in this paper, the zero detection methods for hardware and software problems that have occured as a complemnetary technique was expained.

• 대한조선학회논문집
• /
• 제47권2호
• /
• pp.141-149
• /
• 2010

It is essential to find oscillating angles and periods in a seaway when designing and manufacturing stabilizers. It is difficult to find oscillating angles and periods in high speed turning and they vary with ship speed and wave heading angles, therefore, proper algorithm to measure oscillating periods in a seaway. In the present study, three kinds of algorithms are developed to measure oscillating angles periods in a seaway. Dual axis tilt sensor of low price is used to measure oscillating angles, and the effect of lateral accelerations on tilt sensor have been reduced by the fusion algorithm using the gyro sensor signals. Analog and digital filters are applied to minimize the noise of the signals. Three kinds of algorithms, zero crossing, peak to peak and moving zero crossing algorithm, are developed to measure oscillating periods in a seaway. It is found that the moving zero algorithm showed the best results in the sea trials.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1661-1668
• /
• 2016

A fixed off-time controlled high power factor ac-dc LED driver is proposed in this paper, which employs a novel zero-crossing-compensation (ZCC) circuit based on a fixed off-time controlled scheme. Due to the parasitic parameters of the system, the practical waveforms have a dead region. By detecting the zero-crossing boundary, the proposed ZCC circuit compensates the control signal VCOMP within the dead region, and is invalid above this region. With further optimization of the parameters KR and Kτ of the ZCC circuit, the dead zone can be eliminated and lower THD is achieved. Finally, the chip is implemented in HHNEC 0.5μm 5V/40V HVCMOS process, and a prototype circuit, delivering 7~12W of power to several 3-W LED loads, is tested under AC input voltage ranging from 85V to 265V. The test results indicate that the average total harmonic distortion (THD) of the entire system is approximately 10%, with a minimum of 5.5%, and that the power factor is above 0.955, with a maximum of 0.999.

• 한국초전도ㆍ저온공학회논문지
• /
• 제20권4호
• /
• pp.55-59
• /
• 2018

Currently, the development of industry makes needs larger electric supply. Providers must consider the efficiency about losses and reliability of the system. In this case, DC power system can save electrical energy; long-distance transmission line losses. Relevance to switch technology with a voltage-source converter (VSC) in AC-DC conversion system have been researched. But, protection device of DC-link against fault current is still needed to study much. VSC DC power system is vulnerable to DC-cable short-circuit and ground faults, because DC-link has a huge size of capacitor filter which releases extremely large current during DC faults. Furthermore, DC has a fatal flaw that current zero crossing is nonexistence. To interrupt the DC, several methods which make a zero crossing is used; parallel connecting self-excited series LC circuit with main switch, LC circuit with power electronic device called hybrid DC circuit breaker. Meanwhile, self-excited oscillator needs a huge size capacitor that produces big oscillation current which makes zero crossing. This capacitor has a quite effective on the price of DCCB. In this paper, hybrid self-excited type superconducting DCCB which are using AC circuit breaker system is studied by simulation tool PSCAD/EMTDC.

• 대한전자공학회논문지SD
• /
• 제47권2호
• /
• pp.100-105
• /
• 2010

본 논문에서는 Zero-Crossing 복조기에 적합한 88MHz에서 108MHz 대역 FM 라디오 수신기를 $0.5{\mu}m$ CMOS 공정을 이용하여 설계 및 제작하였다. 본 수신기는 Low-IF 구조를 기초로 설계되었으며, Low-Noise Amplifier (LNA), Down-Conversion Mixer, Phase locked loop (PLL), Low-pass filter (LPF), 비교기를 포함하는 RF/Analog 집적회로로 개발되었다. 측정결과 LNA와 Mixer를 포함하는 RF Block은 23.2dB의 변환 이득과 입력 PldB는 -14dBm였고 전체 잡음지수는 15 dB로 나타났다. IF단 LPF와 비교기를 포함하는 Analog Block은 89dB 이상의 전압 이득을 가지고, IC내부의 레지스터를 제어하여 600KHz에서 1.3MHz까지 100KHz 단위로 Passband 대역를 조절할 수 있도록 설계되었다. 설계된 수신기는 4.5V에서 동작하며, 전체 전류 소모는 15.3 mA로 68.85mW의 전력을 소모한다. 실험결과 성공적으로 FM 라디오 신호를 수신할 수 있었다.

• 대한전기학회논문지
• /
• 제36권5호
• /
• pp.352-359
• /
• 1987

The cycloconverter operating on a circulating current-free mode has many zero crossing points. If an exact zero crossing points are not detected, the three phase-unbalanced currents will flow in a motor. In this paper, the current feedback using a current reference wave is proposed to improve the problems of zero crossing detection, three phase-unbalanced voltages, currents, and torgue ripples. To prevent the saturation of the air gap flux and keep the torque constant, the constant voltage / hertz control with IR compensation is adopted. The PI-controller is designed using the linearized model of the cycloconverterinduction motor system. Alsi, Z-80A single board computer has been used to implement the proposed scheme which results in the performance improvement of cycloconterter-fed induction motor speed control system.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.426-430
• /
• 2005

The fiber-optic interferometer which is a powerful application for nondestructive measurement techniques has many advantages such as capability of making portable system, easy optical arrangement, low optical loss. In spite of these advantages, this system has an environmental sensitivity of thermal drifts and vibrations. Against environmental perturbations and nonlinear characteristic of phase modulator, the accurate and fast ${\pi}/2$ phase stepping has been achieved by using zero-crossing detection. CCD camera trigger signal is generated at the 4 zero-crossing points. Our System has achieved up to 100 Hz of image capture speed and 0.6 mrad of accuracy of phase stepping, accuracy.

• Journal of Power Electronics
• /
• 제18권2호
• /
• pp.323-331
• /
• 2018

Buck power factor correction (PFC) converters, compared with conventional boost PFC converters, exhibit high efficiency performance in the entire range of universal line voltage. This feature has gotten more attention for eliminating the zero crossing dead angle of buck PFC rectifiers. Furthermore, bridgeless structures for the reduction of conduction losses have been proposed. The aim of this paper is to introduce a single-phase buck rectifier that simultaneously has unity power factor (PF) and bridgeless structure while operating in the continuous conduction mode (CCM). For this purpose, two auxiliary flyback converters without any active switches are applied to a bridgeless buck rectifier to eliminate the zero crossing dead angle and achieve unity power factor, low total harmonic distortion (THD) and high efficiency. The operation and design considerations of the proposed rectifier are verified on a 150W, 48V prototype using a conventional peak-current-mode control. The measurement results show that the proposed rectifier has nearly unity power factor, THD less than 7% and high efficiency.

• 조명전기설비학회논문지
• /
• 제28권12호
• /
• pp.65-73
• /
• 2014

In this paper, the detection scheme of the voltage variation using a two difference voltage is proposed. The conventional sag detector is from a single-phase digital phase-locked loop (DPLL) that is based on a d-q transformation using an all-pass filter (APF). The APF generates a virtual q-axis voltage component with $90^{\circ}$ phase delay but the APF cannot generate the virtual q-axis voltage depending on the phase of the grid voltage. To overcome the problem, q-axis voltage component is generated from difference between the current and previous value of d-axis voltage component in the stationary reference frame. However, the difference voltage around the zero crossing is not enough to detect the voltage sag. Therefore, the new detection scheme using the two difference voltage which can detect the sag around the zero crossing voltage is proposed.