• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.364-367
• /
• 2001

ZVS Full-bridge converter is widely used in medium power level(1-3kW). ZVS can be designed within a limited load range and ZVS failure at light load condition is assumed to be acceptable within the given efficiency and thermal constraints. However, unbalanced ZVS resonant energy caused by dc blocking capacitor may alleviate the switching loss problem at light load condition. ZVS resonant energy is unbalanced by do blocking capacitor. This problem causes loss and heat concentration of a switch leg, In this paper, this problem is analyzed, and a novel control method is proposed to solve the problem.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.6
• /
• pp.49-57
• /
• 2001

This paper analyzed PFC of active clamp ZVS flybark converter by adding two method PFC (Power Factor Correction) circuit-two-stage and single-stage. The addition of active clamp circuit also provide a mechanism fur achieving ZVS of both the primary and auxiliary switches. ZVS also limits the turn off di/dt of the output rectifier, reducing rectifier switching loss and switching noise, due to diode reverse recovery. As a results, the proposed converters have characteristics of the reduced switching noise and high efficiency in comparison to conventional flyback converter. The simulation and experimental results show that the proposed converters improve the input PF of 300[W] ZVS flyback converter by adding single-stage two-stage PFC circuit.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.2
• /
• pp.167-174
• /
• 2015

This study describes how digital time delay deteriorates control performance in zero voltage switching (ZVS) phase-shifted full bridge (PSFB) converter. The small-signal model of the ZVS PSFB converter is derived from the buck-converter small-signal model. Digital time delay effects have been considered according to the digital sampling methods. The analysis verifies that digital time delays reduce the stability margin of the converter, and the double sampling technique exhibits better performance than the single sampling technique. Both simulation and experimental results based on 250 W ZVS PSFB confirm the validity of the analyses performed in the study.

• Proceedings of the KIPE Conference
• /
• 1996.06a
• /
• pp.71-75
• /
• 1996

As the Three-level ZVS PWM DC-DC converter operates likewise full-bridge ZVS PWM DC-DC converter and the blocking voltage of each switching device is a half of the DC-link voltage, it is suitable for the high imput voltage applications. However, it has some problems as follows; The blocking voltage of each devices is unbalanced and it causes the power losses of the inner switching devices to be increased. Also, it has narrow load range so that the switching losses and the efficiency are reduced as it goes to the light load. This paper presents an nove Three-level ZVS PWM DC-DC converter, which can reduce the overvoltage of the outer switches, eliminate the unbalance of the voltage sharing between the switches at turn-off due to the stray inductances, and operate from no load to full load. The characteristics and the performances of the proposed Three-level ZVS PWM DC-DC converter are verified by simulation and experimental results

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.3
• /
• pp.265-272
• /
• 2001

The traditional 60[Hz] power supply for during magnetron in microwave oven has disadvantages of heavy weight and low efficiency due to 60[Hz] High Voltage Transformer(HVT), capacitor and th phase control of thyristors. To alleviate these disadvantages, this paper proposes a 20[kHz] phase-shifted Full-Bridge(FB) Zero-Voltage-Switched(ZVS) PWM converter for driving a 600[W] magnetron in an 1[kW] microwave oven. The proposed converter has advantages of light weight and high power density.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.3
• /
• pp.37-44
• /
• 1998

This paper compared to the operation performance and efficiency of an interleaved active clap ZVS forward converter and an interleaved ZVS half-bridge converter in distributed power system. The design for the current-mode control circuit of an interleaved active clamp ZVS forward converter is presented. To simplify the gate drive circuits, N-P MOSFETs coupled active clamp method is proposed. An efficiency about 90% for the 50∼100% load range is achieved.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.615-619
• /
• 2004

A new asymmetrical zero voltage switching (ZVS) active clamp forward converter is proposed. Since the ripple current of secondary inductor plays a key role in the ZVS operation of main power switch, the proposed converter shows an excellent ZVS performance. The synchronous rectification is employed to reduce the rectification loss. The operational principle and ZVS analysis are presented. Experimental results demonstrate that the proposed converter can achieve an excellent ZVS performance throughout all load conditions and the significant improvement in the efficiency for the 100W(5V,20A) prototype converter.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.3
• /
• pp.96-102
• /
• 1998

This paper describes the design of the digital controller for Full-Bridge Phase-shifted converter with zero-voltage switching (ZVS). Although digital control techniques are widely used in the area of inverters and motor drives, their use for the control of high-frequency switching power supply is still rare. Therefore, this paper presents design method of digital controller of Full-Bridge Phase-shifted converter with zero-voltage switching (ZVS) and compares with conventional analog controller. The controller design is optimized by running computer simulation with the MATLAB numerical calculation package.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.2
• /
• pp.31-37
• /
• 2001

This paper propose ZVS-HB type resonant DC/DC converter have earth different output characteristics using division ratio, not only a source division function but a resonant function and soft switching technique(ZVS, ZCS) instead of conventional source division capacitor. Circuit analysis generally described using normalized parameters most of characteristics with division ratio of source division capacitor. Also, this paper citified a rightfulness of characteristic analysis in comparison with a theoretical values and a experimental values obtain from experiment using Power-MOSFET.

• Journal of Power Electronics
• /
• v.6 no.3
• /
• pp.187-194
• /
• 2006

A new asymmetrical pulse width modulation (PWM) half bridge converter with improved ZVS performance is proposed. The ZVS operation of the proposed converter can be maintained from no load to full load conditions since the magnetizing current of the transformer contributes to the ZVS operation at light loads without considerable conduction loss of the transformer and switch. Synchronous rectification is employed to reduce the rectification loss. Operational principles, large signal modeling, ZVS analysis and design equations are presented. Experimental results demonstrate that the proposed converter can achieve a large ZVS range and significant improvement in efficiency for a 100W (5V, 20A) prototype converter.