• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.3
• /
• pp.37-42
• /
• 2010

Plastic region tightening is widely used in critical bolted joints in internal combustion engines in order to reduce the engine weight by maximizing the use of load-carrying capacity of bolt. Mechanical behavior of bolt tightened in plastic region under external axial tensile load is investigated for various friction conditions using three dimensional finite element analysis. The behavior of bolt tightened in elastic region as well as that in tensile test are investigated for comparison. Tightening process is simulated by rotating the bolt in order to examine the friction effect realistically. It is revealed that the bolt tightened in plastic region can carry more external load until the joint is opened, and yields at lower bolt load than the bolt tightened in elastic region. The friction coefficient has effect on the yield load, but not on the load-carrying capacity. Moreover, the scatter in the bolt preload due to friction begins with plastic deformation of bolt in the angle tightening control, whereas it begins with the onset of tightening in the torque tightening control. The observations are interpreted with the residual torsional stress in the bolt generated during the tightening.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.26 no.1
• /
• pp.23-30
• /
• 2022

This study proposed a simplified finite element analysis procedure for designing the nonstructural masonry wall in the out-of-plane direction. The proposed method is a two-step elastic analysis procedure by bilinearizing the behavior of the masonry wall. The first step analysis was conducted with initial stiffness representing the behavior up to the effective-yield point, and the second step analysis was conducted with post-yield stiffness. In addition, the orthotropic material property of the masonry was considered in the FE analysis. The maximum load was estimated as the sum of the maximum loads in the first and second step analyses. The maximum load was converted into the moment coefficients and compared with those from the yield line method applied in Eurocode 6. The moment coefficients calculated through the proposed procedure showed a good match with those from the yield line method with less than 6% differences.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.9
• /
• pp.2071-2081
• /
• 1995

In order to examine the effects of yield stress, tensile strength and thickness on the buckling behavior during bending of pipes, the nonlinear finite element analysis of the 3-point bending tests was carried out using the commercial software (ABAQUS) under the condition of L4(2$^{3}$) performed according to the designed condition. Form the analysis of simulation results, it was found that yield stress and thickness were the major factors on buckling load at pipe bending and tensile strength gave little influence because the plastic strain and plastic zone are small. For the punch displacement to the occurrence of buckling, thickness is a major factor and yield stress and tensile strength are the minor factors.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.56 no.3
• /
• pp.47-53
• /
• 2014

We investigated the effect of straw mat cover and soil amendments on the reduction of runoff, non-point source pollution load and yield of a Chinese cabbage from alpine fields. Two plots on sandy loam soil were prepared. Experimental treatments were control and rice straw mat cover (3,300 kg/ha)+Polyacrylamide (PAM) (5 kg/ha)+Gypsum (1 ton/ha) (SPG). A variety of Chinese cabbage was cultivated and runoff was monitored during a growing season in 2012. Monitoring was conducted to seven times. Runoff rate of SPG plot was lower than those of control plot. The reduction rate of runoff from SPG plot was 29.4 % compared to control plot. The reduction rate of suspended solids (SS), total nitrogen (TN) and total phosphorus (TP) load of SPG plot was 86.5 %, 34.7 % and 39.1 %, respectively. Yield of a Chinese cabbage from SPG plot (39,646 kg/ha) was greater than that of control plots (28,482 kg/ha). It was concluded that the use of SPG on soil surface could not only reduce the NPS pollution loads in receiving waters but also help increase the crop yield.

• Earthquakes and Structures
• /
• v.9 no.4
• /
• pp.699-718
• /
• 2015

The effect of reinforcing concrete members with high strength steel bars with yield strength up to 600 MPa on the overall seismic behavior of concrete moment frames was studied experimentally and numerically. Three geometrically identical plane frame models with two bays and two stories, where one frame model was reinforced with hot rolled bars (HRB) with a nominal yield strength of 335 MPa and the other two by high strength steel bars with a nominal yield strength of 600 MPa, were tested under simulated earthquake action considering different axial load ratios to investigate the hysteretic behavior, ductility, strength and stiffness degradation, energy dissipation and plastic deformation characteristics. Test results indicate that utilizing high strength reinforcement can improve the structural resilience, reduce residual deformation and achieve favorable distribution pattern of plastic hinges on beams and columns. The frame models reinforced with normal and high strength steel bars have comparable overall deformation capacity. Compared with the frame model subjected to a low axial load ratio, the ones under a higher axial load ratio exhibit more plump hysteretic loops. The proved reliable finite element analysis software DIANA was used for the numerical simulation of the tests. The analytical results agree well with the experimental results.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.1
• /
• pp.61-71
• /
• 2017

The flexural behavior of composite ring stiffened by GFRP and steel pipe is presented in this paper. The effective width is required to construct FEM beam element model to verify the composite flexural behavior of stiffened ring of cylindrical shell structure. The experimental results are compared with the theoretical and FEM results by commercial program ABAQUS to verify the effective width coefficient. The yield, crack and ultimate loads is calculated using theoretical strains that varies depending on yield state and compared with experiment result and FEM results by ABAQUS solid model.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.705-712
• /
• 2005

Among soft ground treatment methods with granular soil used in domestic, the sand compaction pile method has been utilized greatly, but, as a result of exhaustion of sand and increase of unit cost, a necessity of an alternative method is suggested. In this study, the static load tests for group crushed-stone compaction piles which were constructed at in-situ site were performed. Pile diameter was 700mm and area of loading plates were changed. The static load tests of single and group piles were performed for area replacement ratio of 20, 30 and 40%. Based on test results, bearing capacity of group crushed-stone compaction pile were estimated. The more both single pile and group pile increase, the more yield bearing capacity tended to increase. Also, the yield bearing capacity of a group pile is about 50% less than the yield bearing capacity of a single pile. If the ground reinforced with the crushed-stone compaction pile is replacement ratio of $20{\sim}40%$, RIYB of both single pile and group pile increases qualitative tendency of linear more than original ground

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.5
• /
• pp.652-660
• /
• 2015

To study the bearing characteristics of glass fiber reinforced glulam for structural design, bearing strength tests were performed. Bearing loads were applied in the direction parallel to the grains, and the holes were prepared in such a way that the bolts would bear and support all the layers. The yield bearing strengths of the glass fiber reinforced glulam were found to be similar to those of the non-reinforced glulam, and were almost constant regardless of increases in bolt diameter. The ratio of the experimental yield bearing strength to the estimated bearing strength according to the suggested equation of the Korea Building Code and National Design Specification was 0.91~1.03. For the non-reinforced glulam and the sheet glass fiber reinforced plastic glulam, the maximum bearing load was measured according to the splitting fracture of specimens under bolt. The textile glass fiber reinforced glulam underwent only an embedding failure caused by the bearing load. The failure mode of reinforced glulam according to bearing load will influence the failure behavior of bolted connection, and estimating the shear yield strength of the bolted connection of the reinforced glulam is necessary, not only by using the bearing strength characteristics but also using the fracture toughness of the reinforced glulam.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.4
• /
• pp.330-335
• /
• 2012

This study performed the structure analysis for development and localization of main and nose wheel in Korean Helicopter Program(KHP). Structural stability of wheel is evaluated using ANSYS. Considering wheel and tire interface, Stress analysis was conducted by applying pneumatic of tire, static load, radial load and combined load on main and nose wheel. Considering yield strength at which plastic deformation occurs, simulation results suggest the method which increases structure stability after comparing maximum stress and yield strength.

• Structural Engineering and Mechanics
• /
• v.59 no.5
• /
• pp.853-866
• /
• 2016

This paper examines a methodology for computing the probability of structural failure of reinforced concrete beams subjected to fire. The significant load variables considered are dead load, sustained live load and fire temperature. Resistance is expressed in terms of moment capacity with random variables taken as yield strength of steel, concrete class (or grade of concrete), beam width and depth. The flexural capacity is determined based on the design equations recommended in Indian standard IS456:2000. Simplified method named $500^{\circ}C$ isotherm method detailed in Eurocode 2 is incorporated for fire design. A transient thermal analysis is conducted using finite element software ANSYS$^{(R)}$ Release15. Reliability is evaluated from the initial state to 4h of fire exposure based on the first order reliability method (FORM). A procedure is coded in MATLAB for finding the reliability index. This procedure is validated with available literature. The effect of various parameters like effective cover, yield strength of steel, grade of concrete, distribution of reinforcement bars and aggregate type on reliability indices are studied. Parameters like effective cover of concrete, yield strength of steel has a significant effect on reliability of beams. Different failure modes like limit state of flexure and limit state of shear are checked.