• 한국세라믹학회지
• /
• 제30권11호
• /
• pp.911-918
• /
• 1993

X-ray photoelectron spectroscopy(XPS) has been empolyed to investigate the structure of PbO-Bi2O3-Ga2O3 glasses. XPS OIS spectra recorded from binary PbO-Ga2O3 glasses clearly showed the presence of two peacks due to bridging and non-bridging oxygens, respectively. Gaussin best-fit deconvolution of the OIS peaks suggested there are substaintial amount of non-bridging oxygens in the structure. Therefore, in addition to the glassforming and charge compensating roles of PbO as suggested from the previous works, role of PbO as network modifiers needs to be considered. Addition of Bi2O3 to binary glasses resulted in the rapid decrease in the amount of non-bridging oxygens as well as in values of FWHM (Full Width at the Half Maximum intensity). It is believed that Bi2O3 form distorted BiO6 octahedra and therefore, work as intermediates. Infrared spectra also suggested that Ga2O3 behave as network-formers in the form of GaO4- tetrahedra.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권5호
• /
• pp.211-215
• /
• 2001

SBT thin films were etched at different content of $Cl_2$ in $Cl_2$/Ar or $Cl_2/N_2$(80%). As $Cl_2$ gas increased in $Cl_2$/Ar or $Cl_2/N_2$ gas plasma. the etch rate decreased. The result indicates that physical puttering of charged particles is dominant to chemical reaction in etching SBT thin films. To evaluate the etching mechanism of SBT thin films, x-ray photoelectron to chemical reaction in etching SBT thin films. To evaluate the etching mechanism of SBT thin films, x-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS) and atomic force microscopy (AFM) were carried out. From the result of AFM, the rms values of etched samples in Ar only or $Cl_2$ only plasma were higher than that of as-deposited, $Cl_2$/Ar and $Cl_2/N_2$ plasma. This can be illustrated by a decrease of Bi content of nonvolatile etching products (Sr-Cl and Ta-Cl), which are revealed by XPS and SIMS.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권10호
• /
• pp.553-558
• /
• 2000

This paper deals with change of contact angle, surface potential decay, surface resistivity and XPS of water-treated epoxy insulator. From the experimental results on the contact angle was reduced from $74^{\circ}$to $24^{\circ}$ due to the formation of polar hydroxyl groups on surface which was associated with intermolecular reaction between epoxy chains of three-dimensional network structure and water molecules. From the experimental results in the surface potential decay of water treated-samples, it was found that the accumulation of charge is decreased and the surface potential decay time is shortened by the interaction of polar hydroxyl groups induced on the treated surface as the increment of treatment time. The positive charging on the treated surface compared with negative charging is relatively lowered by the induction of polar hydroxyl groups. The surface resistivity was changed from $10^{15}[{\Omega}/cm^2$] to $10^{12}[{\Omega}/cm^2$] caused by water treatment. From XPS, it was found that the changes affected by the surface degradation of epoxy were caused by the generation of carboxyl groups through the chain decomposition and recombination with oxygen molecules in the air.

• Transactions on Electrical and Electronic Materials
• /
• 제3권3호
• /
• pp.29-33
• /
• 2002

A procedure was developed for preparing bulk carbon nitride crystals from a polymeric $\alpha$ -C$_3$N$\_$4.2/ at high pressure and temperature in the presence of seeds of crystalline carbon nitride films prepared by a high voltage discharge plasma combined with pulsed laser ablation of graphite target. The samples were evaluated by x-ray photoelectron spectroscopy (XPS), infrared (IR) spectroscopy, Auger electron spectroscopy (AES), secondary-ion mass spectrometry (SIMS), scanning electron microscopy (SEM) and x-ray diffraction (XRD). Notably, XPS studies of the film composition before and after thermobaric treatments demonstrate that the nitrogen composition in $\alpha$ -C$_3$N$\_$4.2/ material initially containing more than 58% nitrogen decreases during the annealing process and reaches a common, stable composition of ~45%. The thermobaric experiments were performed at 10-77 kbar and 350-1200 $\^{C}$.

• 한국표면공학회지
• /
• 제52권6호
• /
• pp.342-349
• /
• 2019

Titanium nitride(TiN) thin films have been deposited on PEN(Polyethylene naphthalate) substrate by reactive RF(13.56 MHz) magnetron sputtering in a 25% N₂/Ar mixed gas atmosphere. The pulsed DC bias voltage of -50V on substrates was applied with a frequency of 350 kHz, and duty ratio of 40%(1.1 ㎲). The effects of pulsed DC substrate bias voltage on the crystallinity, color, electrical properties of TiN_x films have been investigated using XRD, SEM, XPS and measurement of the electrical properties such as electrical conductivity, carrier concentration, mobility. The deposition rates of TiN_x films was decreased with application of the pulsed DC substrate bias voltage. The TiN_x films deposited without and with pulsed bias of -50V to substrate exhibits gray and gold colors, respectively. XPS depth profiling revealed that the introduction of the substrate bias voltage resulted in decreasing oxygen concentration in TiN_x films, and increasing the electrical conductivities, carrier concentration, and mobility to about 10 times, 5 times, and 2 times degree, respectively.

• 한국전기전자재료학회논문지
• /
• 제16권7호
• /
• pp.564-568
• /
• 2003

The etching of Au thin films have been performed in an inductively coupled CF$_4$/Cl$_2$/Ar plasma. The etch rates were measured as CF$_4$ contents added from 0 to 30 % to Cl$_2$/Ar plasma, of which gas mixing ratio was fixed at 20%. Other parameters were fixed at an rf power of 700 W, a dc bias voltage of 150 V, a chamber pressure of 15 mTorr, and a substrate temperature of 3$0^{\circ}C$. The highest etch rate of the Au thin film was 3700 $\AA$m/min at a 10% additive CF$_4$ into Cl$_2$/Ar plasma. The surface reaction of the etched Au thin films was investigated using x-ray photoelectron spectroscopy (XPS) analysis. XPS analysis indicated that Au reacted with Cl and formed Au-Cl, which is hard to remove on the surface because of its high melting point. The etching products could be sputtered by Ar ion bombardment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.45-48
• /
• 2000

High dielectric (Ba,Sr)TiO$_3$ thin films were etched in an inductively coupled plasma (ICP) as a function of C1$_2$/Ar gas mixing ratio. Under Cl$_2$(20)/Ar(80), the maximum etch rate of the BST films was 400$\AA$/min and selectivities of BST to Pt and PR were obtained 0.4 and 0.2, respectively. We investigated the etched surface of BST by x-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and x-ray diffraction (XRD). From the result of XPS analysis, we found that residues of Ba-Cl and Ti-Cl bonds remained on the surface of the etched BST for high boiling point. The surface roughness decreased as Cl$_2$ increases in Cl$_2$/Ar plasma because of non-volatile etching products. This changed the nature of the crystallinity of BST. From the result of XRD analysis, the crystalliility of etched BST film maintained as similar to as-deposited BST under Ar only and Cl$_2$(20)/Ar(80). However, (100) orientation intensity of etched BST film abruptly decreased at Cl$_2$ only plasma. It was caused that Cl compounds were redeposited on the etched BST surface and damaged to crystallinity of BST film during the etch process.

• 한국전기전자재료학회논문지
• /
• 제13권2호
• /
• pp.114-119
• /
• 2000

Etch characteristics of SF6/CI2 electron cyclotron resonance (ECR) plasmas have been investigated. Surface reaction of gas plasma with polysilicon was also analysed using X-ray photoelectron spectroscopy (XPS). At the same time, the relationship between surface reaction and the etched profile of polysilicon was examined using XPS. The etch rate of polysilicon and oxide increases with increasing flow rate of SF6 in the SF6/CI2 gas mixture, and tis selectivity also increase also increase. It was also found that as increasing flow rate of SF6 in the SF6/CI2 gas mixture, the atomic% of chlorine detected at surface region decrease, but F and S contents increase. At the same time, when the mixing ratio of SF6 gas increases, the anisotropy of etched polysilicon is sharply decreased in the 0%~10% range of the SF6 mixing ratio, but is rarely varied in the range over 10%, in spite of the large variations in flow rates. It can be explained that the bonding of S-Si due to SiSx(x$\leq$2) compound formed on the etched surface suppress the formation of Si-Cl and 'or Si-F bonding in the silicon etching.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.132-133
• /
• 2006

PRAM (phase-change random access memory)은 전류 펄스 인가에 따른 기록매질의 비정질-결정질 간 상변화와 그에 동반되는 저항변화를 이용하는 차세대 비휘발성 메모리 소자로서 연구되어지고 있다. 본 논문에서는 $(GeTe)_x(Sb_2Te_3)$ pseudobinary line을 따르는 조성(x=0.5, 1, 2, 8)의 벌크 및 박막시료를 제작하고 원자-스케일의 구조적 상변화를 분석하였다. 열증착을 이용하여 Si 기판위에 200nm 두께의 박막을 형성, 질소분위기 하에서 100-450도 범위에서 열처리 하였다. XRD를 통해 열처리 온도에 따른 구조적 분석을 실시하였다. x=8의 조성을 제외한 전체 박막에 대해 열처리 온도 증가에 따라 fcc와 hexagonal 구조가 순차적으로 나타났으며 일부에서는 혼종의 상구조를 보였다. 특히, $Ge_2Sb_2Te_5$ 박막에 대하여 EXAFS (extended x-ray absorption fine structure) 및 XPS를 이용하여 상변화의 원자-스케일 구조분석을 하였다.

• 한국진공학회지
• /
• 제7권2호
• /
• pp.112-117
• /
• 1998

TiN을 Cu의 확산방지막으로 사용하기 위해 많은 연구가 되어왔는데, 이 연구에서는 특히 X-ray photoelectron spectroscopy(XPS)를 이용하여 TiN박막에서의 Cu의 확산현상을 연구하였다. TiN박막은 일반적으로 columnar grain을 형성하면서 성장을 하는데, 녹는점의 1/3에 해당하는 비교적 낮은 온도에서는 grain들의 경계를 따라 Cu가 확산함을 확인하였다. Atomic force microscopy(AFM)를 이용하여 grain의 모양을 관찰하였고, 이 grain boundary 를 통한 확산 현상을 연구하기 위하여, modified surface accumulation method를 이용하였 다. 연구 결과, TiN박막에서의 Cu의 grain boundary diffusion의 활성화 에너지 $Q_b$는 0.23 eV, Diffusivity $D_{bo}$는 $5.5\times10^{-12{\textrm{cm}^2$/sec의 값을 얻었다.