• 대한치과기공학회지
• /
• 제11권1호
• /
• pp.95-102
• /
• 1989

This study was performed to study the efficiency of a local ventilation system, installed in dental laboratories, and of two types of protecting face masks. The dust originating from the workpiece as well as from the wheels and stones was collected on air filters in the cutting cycle during coarse and fine grinding, and in the subsequent polishing procedures of each specific dental material. The efficiency of the ventilation system was measured on the basis of weight reduction of dust in the breathing air at a distance about 20-40 cm from workpiece. The results were as follows: 1. Use of the local ventilation system reduced the amounts of respirable dust to an average level of 21.4%, although the efficiency of the local ventilation system varied depending upon materials used. 2. Mounting a nozzle on the tube improved the efficiency of the ventilation system considerably. The efficiency of the local ventilation system also increased as the workpiece was closing to the tube inlet. 3. With or without the local ventilation system, the distance between the position of the workpiece and sampler greatly affected the dust level. 4. The face masks covering the sampler improved the efficiency of the ventilation system considerably.

• 한국산학기술학회논문지
• /
• 제16권3호
• /
• pp.1645-1651
• /
• 2015

본 연구에서는 선삭 작업에서 가공 여유각 변경에 따른 피삭재의 형상정밀도가 어떻게 변화되는지 분석하고자 하였다. 피삭재는 3가지로 SM45C(기계구조용탄소강), SCM415(크롬몰리브덴강), STS303(스테인리스강)을 선택하여 정해진 가공조건인 회전속도 2,500 rpm으로 시작하여 이송속도 0.07 mm/rev와 0.10 mm/rev를 기준으로 가공깊이 0.1 mm, 0.2 mm, 0.3 mm 그리고, 절인 경사각인 네거티브 경사각 $0.0^{\circ}(-6.0^{\circ})$, $0.3^{\circ}(-6.3^{\circ})$, $0.9^{\circ}(-6.9^{\circ})$의 3가지 형태로 가공하였을 경우, 재료별 가공정밀도, 원통도, 동축도, 진원도 등의 결과를 비교 분석하였다. 피삭재의 재질별로 알아본 원통도의 정밀도는 $0.0^{\circ}{\rightarrow}0.3^{\circ}{\rightarrow}0.9^{\circ}$의 순으로 $0.9^{\circ}$일 경우가 가장 좋은 원통도 값을 나타냈다. 결과적으로 바이트의 네거티브 경사각이 커지면 정밀도가 특정 부분에서 재질에 관계없이 좋아져서 가공성이 향상됨을 알 수 있었다. 또한, 이송속도와 절삭 깊이에 따라 가공형상이 변화한다는 것과 재질에 따라 다르게 적용되어야 한다는 것을 확인하게 되었다.

• 한국산업융합학회 논문집
• /
• 제7권4호
• /
• pp.325-330
• /
• 2004

The forces acting on the tool are an important aspect of maching. For those concerned with the manufacture of machine tools, a knowledge of the forces in needed for estimation of power reguirements and for the design of machine tool elements tool-holders and fixtures, adequately rigid and free from vibration. The force reguired to form the chip is dependent on the shear yield strength of the work material un der cutting conditions which are cutting speed, workpiece, feedrate, insert type. In this study, FG, ML, MP, MC, C, RT inserts were investigated in turning using SM45C, SCM4, SKD11, SUS316, materials. The diameter of materials was 60mm, 80mm, 110mm. This paper presents MP were lowest and SKD11 were largest of the workpiece in cutting forces.

• 소성∙가공
• /
• 제15권7호
• /
• pp.524-528
• /
• 2006

Although equal channel angular pressing (ECAP), imposing large plastic shear strain deformation by moving a workpiece through two intersecting channels, is a promising severe plastic deformation method for grain refinement of metallic materials, its batch type characteristic makes ECAP inefficient for multiple-passing. Rotary-die ECAP (RDECAP) proposed by Nishida et al. can achieve high productivity by using continuous processing without taking out the samples from the channel. However, plastic deformation behavior during RD-ECAP has not been investigated. In this study, material plastic flow and strain hardening behavior of the workpiece during RD-ECAP was investigated using the finite element method. It was found that plastic deformation becomes inhomogeneous with the number of passes due to an end effect, which was not found seriously in ECAP. Especially, decreasing corner gap with increasing the number of passes was observed and explained by the strain hardening effect.

• 소성∙가공
• /
• 제15권5호
• /
• pp.382-386
• /
• 2006

Preform design is an effective means of achieving the homogeneous deformation of workpiece materials and decreased load in metal forming. However, this approach has not been applied to equal channel angula. pressing (ECAP). In this paper, plastic deformation behavior of workpieces having four different preform shapes during ECAP was investigated using finite element analyses. The results indicated that a preform design of the workpiece head has a beneficial effect on homogeneous deformation, reducing the maximum pressing load at the initial stage and eliminating folding defects at strain concentration points.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The 8th Asian Symposium on Precision Forging ASPF
• /
• pp.59-62
• /
• 2003

The precision cold forging of helical gear for steering pinion has been studied. Because of the large helix angle, there are many difficult problems to control the material flow and part dimension. The die shape was proposed to improve the flow of workpiece. In order to improve the dimensional accuracy of forged part, a FE analysis was performed. The proposed die shape drives to flow amicably workpiece. The applied load was reduced up to 10 percent, compared to the conventional-shaped-die. The elastic deformation of die has been investigated quantitatively by the 3-dimensional FE analysis. The die-land has been expanded up to $10{\mu}m$ on loading stage, based on the FEM results. Therefore, the elastic deformation amounts should be taken into consideration to improve the dimensional accuracy of forged helical gear.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권2호
• /
• pp.11-17
• /
• 2008

Critical erosion kinetic energy models for radial/median cracks and lateral cracks in a workpiece are established in this study. We used experimental results to demonstrate that the fracture erosion resistance and erosion machining number could be used to evaluate the brittle fracture resistance and machinability of a workpiece. Erosion kinetic energy models were developed to predict brittle fracture and ductile shear, and a critical erosion kinetic energy model was developed to predict the transition from brittle fracture to ductile shear. These models were verified experimentally.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 금형가공,미세가공,플라스틱가공 공동 심포지엄
• /
• pp.54-58
• /
• 2005

Femtosecond laser is the latest generation pulsed laser delivering shortest pulses. Any solid materials can be machined by it. Femtosecond laser micromachining allows highest precision and minimal heat influence within the workpiece. But due to the complex physical phenomena between the laser beam and the workpiece materials, it is very difficult to determine the optimal process conditions in the femtosecond laser micromachining. In this study, a method to simulate the femtosecond laser micromachining process was proposed. And femtosecond laser micro patterning processes of chromium thin film are simulated by the proposed method using a commercial FE code, LS-Dyna. Simulation results were compared with those of experiments.

• 한국분말재료학회지
• /
• 제22권1호
• /
• pp.6-9
• /
• 2015

In this study, the behavior of densification of copper powders during high-pressure torsion (HPT) at room temperature is investigated using the finite element method. The simulation results show that the center of the workpiece is the first to reach the true density of copper during the compressive stage because the pressure is higher at the center than the periphery. Subsequently, whole workpiece reaches true density after compression due to the high pressure. In addition, the effective strain is increased along the radius during torsional stage. After one rotation, the periphery shows that the effective strain is increased up to 25, which is extensive deformation. These high pressure and severe strain do not only play a key role in consolidation of copper powders but also make the matrix harder by grain refinement.

• 대한금속재료학회지
• /
• 제46권3호
• /
• pp.144-149
• /
• 2008

Equal channel angular pressing (ECAP) has been studied intensively over the decade as a typical top-down process to produce ultrafine/nano structured materials. ECAP has successfully been applied for a processing method of severe plastic deformation to achieve grain refinement of magnesium and to enhance its low ductility. However, difficult-to-work materials such as magnesium and titanium alloys were susceptible to shear localization during ECAP, leading to surface cracking. The front pressure, developed by Australian researchers, can impose hydrostatic pressure and increase the strain level in the material, preventing the surface defect on workpiece. In the present study, we investigated the deformation and fracture behavior of pure magnesium using experimental and numerical methods. The finite element method with different ductile fracture models was employed to simulate plastic deformation and fracture behavior of the workpiece.