• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.3
• /
• pp.317-321
• /
• 1986

In this paper the design of a new microstrip wide-band microwave discdriminator is presented which is composed of a binary power divider, an open stub and a shorted stub. The microstrip line frequency discriminator is designed at the center frequency of 3.2GHz. Measured discriminating bandwidth is about 20% and return loss is 15dB or more over that frequency range. Experimetal results are in good agreement with the theory.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.4
• /
• pp.424-431
• /
• 2008

Recently, it is required that acoustic transducers for underwater detection and communication sensor have wide bandwidth and low operating frequency. In this research, the new acoustic transducer is proposed. This transducer is tonpilz type, and made of 1-3 piezoelectric composites as a driving parts. The developed transducer is evaluated the TVR(transmission voltage response) and RVS(receiving voltage sensitivity) characteristics around $4{\sim}14\;kHz$ frequency range and is compared to conventional tonpilz transducer made of solid piezoelectric ceramics as a driving parts. The resonance frequency of the developed transducer is decreased by 30% and the -3 dB bandwidth is increased by 90%, compared to conventional transducer with same dimensions. The value of TVR is decreased by 9 dB and The value of RVS is the same at resonance frequency.

• Journal of IKEEE
• /
• v.12 no.4
• /
• pp.225-233
• /
• 2008

This paper presents a compact, low insertion loss, sharp rejection and wide band microstrip band pass filter that is composed rectangular loop resonator and step-impedance-open-stub(SIOS) for wireless data communication. The SIOS can be reduce length about 30% more than general 0.25${\lambda}$ stub. And stubs can have the advantage of tuning impedance magnitude. In order to demonstrate agrement of this paper prove, the optimized wide band pass filters are realized and experimented. A transmission line model used to calculate the frequency response of the new filters shows good agreement with measurements. The filter with perturbation stubs has four poles at rejection band, the poles are excited 3.610GHz, 4.265GHz at low frequency band, 8.494GHz, 9.056GHz at high frequency band. And the filter has 3dB fractional bandwidth of 57%(3.695GHz), an insertion loss of better than 0.37dB from 4.549GHz to 8.244GHz, and two rejection of greater than 30dB within 237MHz(4.312GHz${\sim}$ 4.549GHz) at low frequency band, 234MHz(8.244GHz-8.491GHz) at high frequency band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.12A
• /
• pp.951-957
• /
• 2003

The analysis of RF performance requirement conditions on communication system is critical indicator to predict the performance of system. UWB(Ultra Wide Band) system which the standard is not established yet is difficult to derive the precise system performance requirement condition. Also, there are differences between conventional UWB system and multi-band system about RF performance requirement condition. In this thesis, the differences are analyzed and performance requirement conditions of multi-band UWB system are described on the basis of the differences. Throughput, maximum transmit power, and sensitivity of multi-band UWB system is varied with respect to the number of Sub-Bands. In addition, because of Multi-path effect, if PRF(Pulse Repetition Frequency) is changed, the Multi-path link margin is happened to compensate for Multi-path Energy Loss which is contributed by increasing of the Link Margin. According to Multi-path Margin, the variation of the resistance with respect to sensitivity and interference signal is observed and analyzed through the simulation.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.257-261
• /
• 2001

This paper presents the implementation of wide-band RFIC amplifier operating from near 50MHz to 3GHz using Tachyonics SiGe HBT foundry. Voltage shunt feedback is used for the flat gain and the broad band impedance matching. Initial design parameters are calculated using the low frequency small signal analysis. Since the HBT model was not available at the design time, discrete tuning board was made for fine tuning in the low frequency range. Fabricated amplifier shows 12dB gain with 1dB fluctuation and PldB reaches 15dBm at 850MHz.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.2
• /
• pp.7-10
• /
• 2010

In this paper, we design a modem SoC (System on Chip) for low power consumption and high speed wireless communications. Among various schemes of high speed communications, an MB-OFDM (Multi Band-Orthogonal Frequency Division Multiplexing) UWB (Ultra-Wide-Band) chip is designed. The MB-OFDM uses wide-band frequency to provide high speed data rate. Additionally, the system imposes no interference to other services. The 90nm CMOS (Complementary Metal-Oxide Semiconductor) technology is used for the SoC design. Especially, power management mode is implemented to reduce the power consumption.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.497-498
• /
• 2011

In 21 century, we use a variety of new wireless technologies focuses on broadcasting and Communications. Because of widely spread wireless-service, demand a lot of frequency. It requires various wireless access technologies. Especially UWB, SER, Millimeter Wave etc. Among them, UWB can use wide Frequency band, because it is different from Non-traditional approach which Frequency Band Using the exclusive rights granted by. Furthermore, it does not cause interference to other existing frequency, therefore this technology is attracting attention. In this paper, describe study on a UWB technology, design about useable antenna for UWB communication.

• Journal of Satellite, Information and Communications
• /
• v.11 no.4
• /
• pp.107-113
• /
• 2016

In this paper, we suggest a design method of a wide-band Butler matrix working at 5.9 GHz for V2X communication antennas. Since V2X communication needs beam-forming and beam-steering antennas to make transportation systems, mobile comm platforms, saturated frequency-resources, and signal TX-and-RX smart, multi-functional, resolved, and efficient utmost, respectively, the proper Butler matrix and its radiating elements as a low-profile geometry are realized. The constitutive components of the basic Butler matrix of a narrow band are designed first. And then, it is extended to a wide-band version to make its frequency-shift less affected by the event of the antenna system being mounted on a car body. The beam-forming and beam-steering performance is presented as the common feature tagged along with the different bandwidths of the frequency responses as the comparison between the narrow- and wide-band cases.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.6
• /
• pp.37-43
• /
• 2013

In this paper, an UWB (Ultra Wide Band) band-pass filter with open stubs using SIR (Stepped Impedance Resonator) structure is presented. The proposed band pass filter (BPF) has SIR structure instead of open stubs for UWB application with low insertion loss. The bandwidth of the proposed BPF is 103 % at the center frequency of 5.8GHz and the insertion and return losses are 0.17dB and 13.1dB, respectively. Also, the entire size of the proposed band-pass filter is $21.6{\times}17.8mm^2$.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.1
• /
• pp.24-28
• /
• 2010

This paper is presented on the antenna design for notepc platform. We present the antenna with combination of electric-magnetic radiator for dual-band Wireless Local Area Network (WLAN) service and a High Speed Downlink Packet Access (HSDPA) service. Due to the limited antenna space in notepc platform, the antennas for various wireless communication service should be located at a very small area. In this paper, the magnetic-type radiator works for high frequency band (1.7 - 2.1 GHz) application and the electric-type radiator works for low frequency band (820 - 960 MHz) application. This combination produces wide-band characteristics in the high frequency band. Simulation and experimental results of input impedance and gain characteristics of the proposed antenna are presented. There are good agreements between the simulated and measured S11 and gain values.