• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.299.2-299.2
• /
• 2013

We investigated the potassium remaining on a crystalline silicon solar cell after potassium hydroxide (KOH) etching and its effect on the lifetime of the solar cell. KOH etching is generally used to remove the saw damage caused by cutting a Si ingot; it can also be used to etch the rear side of a textured crystalline silicon solar cell before atomic layer-deposited Al2O3 growth. However, the potassium remaining after KOH etching is known to be detrimental to the efficiency of Si solar cells. In this study, we etched a crystalline silicon solar cell in three ways in order to determine the effect of the potassium remnant on the efficiency of Si solar cells. After KOH etching, KOH and tetramethylammonium hydroxide (TMAH) were used to etch the rear side of a crystalline silicon solar cell. To passivate the rear side, an Al2O3 layer was deposited by atomic layer deposition (ALD). After ALD Al2O3 growth on the KOH-etched Si surface, we measured the lifetime of the solar cell by quasi steady-state photoconductance (QSSPC, Sinton WCT-120) to analyze how effectively the Al2O3 layer passivated the interface of the Al2O3 layer and the Si surface. Secondary ion mass spectroscopy (SIMS) was also used to measure how much potassium remained on the surface of the Si wafer and at the interface of the Al2O3 layer and the Si surface after KOH etching and wet cleaning.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.6
• /
• pp.1002-1012
• /
• 1997

When the presintered ceramics are machined with ceramic tool, the tool life becomes extremely short. The CBN tool exhibits the best performance in dry machining of the ceramics presintered at $1450^{\circ}C$ among all cutting tests. The roughness of the machined surface of the ceramics presintered below $1350^{\circ}C$ is smaller than that of the ceramics presintered at $1450^{\circ}C$ While the performance of the cemented carbide and CBN tools is better in dry than in wet machining, the diamond tool shows adverse tendency. The tool life is not affected by the feed rate and depth of cut. During the following full-sintering after the machining of the presintered ceramics, the surface roughness decreases up to 62%. The finished surface in machining the presintered ceramics is much better than that in machining the full-sintered ceramic.

• Journal of agricultural medicine and community health
• /
• v.26 no.2
• /
• pp.7-14
• /
• 2001

Cases of green tobacco sickness were described. During the cutting of tobacco plants throughout harvest, four cases of green tobacco sickness occurred in August 2001, Korea. The range of age was 42-55 years. The most frequent symptoms included dizziness, weakness, nausea, vomiting, abdominal cramps, headache, and difficulty breathing. All affected individuals worked in fields of wet tobacco, where their clothes became wet from moisture on the plants or sweating. They were all healthy, except one with hypertension. They are all non-smokers. They recovered after fluid and antiemetic administrations within two days. Most of doctors misdiagnosed their symptoms as a pesticide poisoning or heat injury. Green tobacco sickness is a condition that has long been known as an occupational health risk among tobacco harvesters. Nicotine poisoning by dermal absorption is reported to be the cause of green tobacco sickness. In Korea, there are many tobacco harvesters, and most of them may be sticken with green tobacco sickness. But, no case of green tobacco sickness has been reported. We report cases of green tobacco sickness occurred to the tobacco harvesters with a review of articles.

• Korean Journal of Plant Resources
• /
• v.19 no.5
• /
• pp.580-585
• /
• 2006

This experiment was conducted to study the effects of sulphuric acid, cutting, cold stratification and hot water on the germination of Sophora japonica seeds, which have difficulty to germinate because they have hard and thick seed coats. The seeds were immersed in 30, 60 and 90% sulphuric acid for 30 minutes as seed scarifications, and cut 1/8, 2/8 and 3/8 of the opposite parts of radicles. As cold stratification the seeds were wrapped in wet towel, and then stored in plastic bags in a refrigerator $(4^{\circ}C)$ for 3, 5 and 10 days. The seeds were immersed in hot water $(90{\sim}95^{\circ}C)$ for 2,5 and 10 minutes. Pretreated seeds represented different germination properties, respectively. After sulphuric acid treatment, the seeds showed an increase in germination (G) and germination index (GI). Compared to the other treatments, 90% sulphuric acid showed the highest G (31.7%) and GI (6.2). The G and GI of cut seeds decreased with the increase of seed cutting lengths. And G and GI of cold stratificated seeds were not significantly different among the days treated (p=0.258). Two minutes treatment of hot water showed lower G and Gl than control, and the seeds were not germinated in 5 and 10 minutes treatments of hot water. At the result of relative growth rate and T/R ratio of seedlings from pretreated seeds, the seedlings from seeds in 90% sulphuric acid treatment represented the highest relative growth rate and T/R ratio.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.06a
• /
• pp.65-81
• /
• 2003

During the last few decades in Korea, the development of hillside or mountain areas has rapidly increased for infrastructure construction such as railroads, highways and housing. Many landslides have occurred during these constructions. Also, the amount and scale of damage caused by landslides have increased every year. In the case of Far East Asia including Korea, the damage of landslides is consequently reported during the wet season. In this paper, the effect of stabilizing piles on slope stability is checked and the behavior of slope soil and piles are observed throughout the year by field measurements in the large-scale cut slopes. In particular a large-scale cut slope situated on the construction site for the express highway in Donghae, Korea. First of all, The behavior of the slope soil was measured by inclinometers during slope modification. Landslides occurred in this area due to the soil cutting for slope modification. The horizontal deformations of slope soil gradually increased and rapidly decreased at depth of sliding surface indicating that the depth of sliding surface below the ground surface can be predicted. On the basis of being able to predict the depth of the sliding surface, stabilizing piles were designed and constructed in this slope. To ensure the stability of the reinforced slope using stabilizing piles, an instrumentation system was installed. The maximum deflection of piles is measured at the pile head and it is noted that the piles deform like deflection on a cantilever beam. The maximum bending stress of piles is measured at the soil layer. The pile above the soil layer is subjected to lateral earth pressure due to driving force of the slope, while pile below soil layer is subjected to subgrade reaction against pile deflection. As a result of research, the effect and applicability of stabilizing piles in large-scale cut slopes could be confirmed sufficiently.

• 보존과학연구
• /
• s.35
• /
• pp.73-86
• /
• 2014

The Seosanmaaesamjonbulsang (national treasure 84) is carved has a quite developed tectonic line in a precipitous wall of stratified rock to the vertical and horizontal directions. The main buddha and the left part of it have got the biological weathering and the efflorescence has been detected on the shoulder part of the right buddha. It has been caused by the raindrops from upper rock after the dismantling of the protection shelter in 2007. Two proper measures have been taken in order to reduce the weathering and protect it from some damages. The one is removing the contaminant by dry/wet cleaning not to get any damage on the rock. The other is the isolation by the construction of a new waterway used L-30 on the upper part of the rock not to contaminate the surface of Rock-carved triad buddha with the raindrops from upper rock. Moreover, the sunlight for buddha has been increased and good ventilation has been made by cutting down the trees around the Rock-carved triad buddha.

• Korean Journal of Materials Research
• /
• v.28 no.4
• /
• pp.201-207
• /
• 2018

Infrared(IR) heating has many advantages, such as energy efficiency, reduced heating time, cleanliness, equipment compactness, high drying rate and easy automation. These features of IR heating provide widely industrial applications, such as surface heat treatment in semiconductor fabrication, thermoforming of polymers, drying and disinfection of food products, heating to metal forging, and drying of wet materials. In this study, the characteristics of a protected gold mirror were examined by spectrophotometer and the lifetime of the coating layers were evaluated by a cross-cutting method and salt spray test. The effects of manufacturing conditions on the protected gold mirror were seen and remedies for these effects were noted in order to improve the properties of the protected gold mirror in the drying process. The reflectance and lifetime of the protected gold mirror was influenced by manufacturing conditions, such as surface roughness and forming conditions of the anti-oxide layer, the adhesion layer, the reflecting layer and the protection layer. The results of this study showed that the protected gold mirror manufactured using a buffing method for pre-treatment resulted in the most effective reflectance. In addition, $Al_2O_3$ coating on an Al substrate as an anti-oxide layer was more effective than the anodizing process in the test of reflectance. Furthermore, the protected gold mirror manufactured by layers forming of various materials resulted in the most effective reflectance and lifetime when coated with $Al_2O_3$ as the anti-oxide layer, coated Cr as the adhesion layer, and coated $MgF_2$ as the protection layer.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.30 no.1
• /
• pp.28-38
• /
• 2020

Objectives: The purpose of this study is to identify the perceived problems of and suggest improvement measures for asbestos abatement companies in support of asbestos-related systems and policies. Methods: For this study a questionnaire was prepared consisting of current work (two questions), the contribution and necessity of a risk assessment system for asbestos abatement (two questions), and problems with and improvement measures for systems and policies (nine questions). The questionnaires were sent to 2,170 asbestos abatement companies and were returned by 83 companies (return rate = 3.8%). We conducted frequency analysis, ANOVA, and a Chi-squared test at the 5% significance level. Results: Asbestos abatement companies expressed difficulties with complying with wet work (43% of unenrolled managers), negative pressure enclosure (36% of all respondents), and installation and use of decontamination units (26% of all respondents) as stipulated in the relevant regulations. In addition, 43% of the respondents expressed concerns that the expertise of the company was not considered during bidding for asbestos abatement and hoped that an advantage (e.g., bid point) would be given to the upper grades for asbestos risk assessment (38%). Asbestos abatement companies generally rented and used negative pressure devices (including negative pressure recording devices) and suggested that periodic calibration (32%) is needed to ensure the performance of the rented equipment. Finally, the respondents asked for clear definitions for three situations specified in the Occupational Safety and Health Acts: (1) temporarily leaving the asbestos abatement workplace; (2) tasks with less airborne asbestos; and (3) physically breaking or cutting using a machine. Conclusions: The problems and improvement measures identified in this study of asbestos abatement companies can be utilized as fundamental information for the improvement of the systems and policies for safe asbestos abatement.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.4 no.1
• /
• pp.125-129
• /
• 1968

For the study of method for promoting the germination of Korean sod seeds harvseted newly some physical and chemical treatments were tested in this experiment. The summarized results of these tests are as follows: 1. Storage of wet seed in low temperature of 0~$2^{\circ}C$ during 2~30 days was seemed the most effective treatment for promoting the germination of sod seed. 2. The treatment that Soaking and mixing up the seeds in cone sulphuric acid about one and half minutes and then washing off in the water promoted fairly the germination of sod seeds. 3. Better germination of sod seeds was found in the light than in the dark or soil. 4. Cutting the top of seed and crushing of seed coat with sand seemed to promote slightly the germination of sod seeds. 5. No promoting effect for germination of sod seeds was found with treatments of Gibberellin, $NH_4$ $NO_3$ and NAA.

• Archives of Plastic Surgery
• /
• v.40 no.3
• /
• pp.259-262
• /
• 2013

After skin grafting, to prevent hematoma or seroma collection at the graft site, a tie-over dressing has been commonly used. However, although the conventional tie-over dressing by suture is a useful method for securing a graft site, refixation is difficult when repeated tie-over dressing is needed. Therefore, we recommend a redoable tie-over dressing technique with multiple loops threads and connecting silk threads. After the raw surface of each of our cases was covered with a skin graft, multiple loop silk thread attached with nylon at the skin graft margin. We applied the ointment gauze and wet cotton/fluffy gauze over the skin graft, then fixed the dressing by connecting cross-counter multiple loop thread with connecting silk threads. When we opened the tie-over dressing by cutting the connecting silk threads, we repeated the tie-over dressing with the same method. The skin graft was taken successfully without hematoma or seroma collection or any other complications. In conclusion, we report a novel tie-over dressing enabling simple fixation of the dressing to maintain proper tension for wounds that require repetitive fixation. Further, with this reliable method, the skin grafts were well taken.