• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.266-270
• /
• 2006

Noise reduction the noise of a high precision multi-stage gearbox applied at the industrial robot is investigated by experiment such as the modal test and the signal analysis. The signal analysis performed with the waterfall plot representing the power spectrum as a function of the rotating speed. An eccentric load is installed at the gearbox in order to organize similar condition used in the industrial robot. Exciting sources are found out by the waterfall plot, and then the main factor to make the noise is distinguish. For the low-noise gearbox, the gear design parameter is modified and this gearbox is experimented in the same procedure. The results of the test show the noise level of gearbox reduced.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.875-878
• /
• 2004

The noise and vibration diagnostic of the industrial robot reducer is ultimately the purpose. We evaluated a noise and vibration tendency of the industrial robot reducer to be made in the outside (RV reducer) through the experiment. Also, we compared the RV reducer to the industrial robot reducer (RD reducer) in the domestic. We measured the noise level with the sound level meter and analyzed the vibration tendency with the waterfall plot. Through the comparison of RV reducer and RD reducer diagnose the industrial robot reducer. We guessed the improvement direction of RD reducer. (The domestic's industrial robot reducer).

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.641-645
• /
• 2008

In this paper, vibration sources of the BLOC motor are identified and the motor vibrations are reduced by structural modification. For vibration characteristic identification, vibration signals measured by an accelerometer when the BLOC motor is moving. These signals are presented in a waterfall plot in order to find the dependency of frequency components on the motor speed. It is found that main vibration source is BLOC motor test rig. From finite element analyses and some experiments, it is also found that resonances occur because the natural frequencies of the test rig exist in usual driving speed rang. To shift the natural frequencies outside the driving rang, the test rig is modified increase stiffness. It is verified that considerable amount of vibration are reduced by the structural modification.

• Journal of Industrial Technology
• /
• v.24 no.B
• /
• pp.83-87
• /
• 2004

A reduced structure model of a wind turbine generator is designed and manufactured. Mode data are obtained by modal testing and analytical method. Vibration response is measured and investigated under various speed condition by using a waterfall plot. Possibility of severe resonance is observed and the mechanism is explained by using the mode data. Simplified theoretical model gives the 1st resonance frequency of wind turbine structure model. The theoretical model can be applied in the design stage of the wind turbine structure to avoid the severe resonance problem.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.6
• /
• pp.546-552
• /
• 2011

In this study, noise sources of a reducer which is combined a spiral bevel gear and a planocentric gear are identified by experimental method and the noise was reduced by the structure modification of the reducer. In order to identify the noise sources, noise and vibration signals were measured by microphone and accelerometer and these signals were analyzed with waterfall plot. In addition, the frequency response functions were obtained to prove the noise and vibration sources. It was found that the resonance was generated by the gear mesh frequencies and natural frequency of the reducer. The noise of the reducer could be reduced by structure modification.

• Journal of Industrial Technology
• /
• v.26 no.A
• /
• pp.81-88
• /
• 2006

The Chun-cheon Citizen's Bell was cast in memory of hosting the 2010 world leasure conference and a striking ceremony was held at the city hall on December 31, 2005. In this study, vibration and sound of the bell are measured and the property of the magnificent sound of the bell is scientifically investigated. Frequency components making the sound are identified and how the frequency components decrease with time is observed using waterfall plot(3-dimensional frequency spectrum). Beat characteristics of the hum(1st frequency) and the fundamental(2nd frequency)are examined by experiment. Directivity of the sound radiation of the bell is examined by measuring the vibration and sound in several directions. Duration of the vibration and the sound is estimated using damping ratio.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.773-778
• /
• 2008

The subway noise in curved line is affected not only by rail condition but also wheel condition and dynamic characteristics. The railway curving noise can be divided into 2 categories. The first is noise depending on the vehicle speed, and the second is the one independent on vehicle speed. In this study the noises were reviewed by using eigen-mode of wheel and waterfall plot which shows noise level in time-frequency domain. And also those were reviewed in viewpoint of stick-slip noise and wheel flange contact noise.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1145-1151
• /
• 2007

In this paper, vibration sources of an electric forklift are identified and the forklift vibrations are reduced by structural modification. For vibration identification, vibration signals are measured by an accelerometer when the forklift is moving. These signals are presented in a waterfall plot in order to find the dependency of frequency components on the forklift speed. It is found that main vibration source is tire pattern excitation. From some experiments and finite element analyses, it is also found that resonances occur because the natural frequencies of the forklift exist in usual driving speed range. To shift the natural frequencies outside the driving speed range, the connection parts between main body and loader are modified to increase stiffness. It is verified that considerable amount of vibration are reduced by the structural modification.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.04a
• /
• pp.51-56
• /
• 2011

In this study, noise sources of a reducer which is combined a spiral bevel gear and a planocentric gear are identified by experimental method and the noise was reduced by the structure modification of the reducer. In order to identify the noise sources, noise and vibration signals were measured by microphone and accelerometer and these signals were analyzed with waterfall plot. In addition, the frequency response functions were obtained to prove the noise and vibration sources. It was found that the resonance was generated by the gear mesh frequencies and natural frequency of the reducer. The noise of the reducer could be reduced by structure modification.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.1
• /
• pp.80-86
• /
• 2008

In this study. the noise sources were identified and the noise and vibration were reduced for an industrial forklift. To identify the noise sourses, noise signals were measured by a microphone on a driver seat and these signals were analyzed with a waterfall plot. For this purpose, the gear mesh frequencies from the gear box of a reducer were not only investigated but noise/vibration sourses of an electric motor were also examined. Furthermore, the frequency response functions were obtained to confirm the vibration and noise sourses. It was found that severe vibration and noise were generated in the casing and the connecting part of the reducer. The severe vibration and noise could be reduced by a structure modification.