• Applied Science and Convergence Technology
• /
• v.24 no.2
• /
• pp.41-46
• /
• 2015

Transparent conductive oxides (TCOs) are essential material in optoelectronics such as solar cells, touch screens and light emitting diodes. Particularly TCOs are attractive material for infrared cut off film due to their high transparency in the visible wavelength range and high infrared reflectivity. Among the TCO, Indium tin oxide has been widely used because of the high electrical conductivity and transparency in the visible wavelength region. But ITO has several limitations; expensive and low environmental stability. On the other hands, fluorine doped tin oxide (FTO) is well known for low cost, weather ability and stable in acidic and hydrogen. In this study, two different magnetron sputtering techniques with RF and DC modes at room temperature deposition of FTO thin film was conducted. The change of oxygen content is influence on the topography, transmittance and refractive index.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.405-406
• /
• 2008

The amorphous indium zinc oxide (IZO) thin films were deposited on polyethersulfone (PES) and glass substrates by facing targets sputtering. IZO thin films deposited as functions of gas flow ratio on PES and glass substrates, respectively. The electrical, optical and structural properties of IZO thin films were evaluated by a Hall Effect Measurement, an X-Ray Diffractormeter, UV/VIS spectrometer in visible range and a scanning electron microscopy, respectively. As-deposited IZO thin films exhibited resistivity of $5.4\times10^{-4}$ and $4.5\times10^{-4}$ [$\Omega$-cm] on PES and glass substrates, respectively. The optical transmittance showed over 85% in the visible region on PES and glass substrates.

• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.1
• /
• pp.35-40
• /
• 2001

A spectral measurement system for reflection and transmission properties by using an optical fiber and an ellipsoidal mirror was newly developed. The hemispherical reflectance and transmittance spectra of several heating resisting ceramics materials were measured from visible to middle infrared region. The directional characteristics of reflection and transmission were also investigated in consideration of the absorptance. The measured data were analyzed by using a four flux model of radiation transfer, The radiation properties could be estimated by the obtained scattering and absorption coefficient spectra.

• Journal of the Korean Ceramic Society
• /
• v.27 no.3
• /
• pp.389-393
• /
• 1990

PLZT(9/65/35) powders and ceramics were obtained by coprecipitation method from aqueous salt solution and its powder and sintering properties were investigated. Single phase of PLZT was synthesized about 53$0^{\circ}C$ and its average particle size was 1${\mu}{\textrm}{m}$. Specimen which was sintered at 1275$^{\circ}C$ for 30 hours under 1atm and PbZrO3 atmosphere powders, showed 45% of optical transmittance in visible range for 0.27mm thickness sample.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.990-993
• /
• 2006

We fabricated top emission organic light emitting diode (TEOLED) with transparent metal cathode Barium and Silver bilayer. Very thin Ba/Ag bilayer was deposited on the organic layer by thermal evaporation. This cathode shows high transmittance over 70% in visible range. And the device with a Ba-Ag has a low turn on voltage and good electrical properties.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.578-580
• /
• 2003

PEDOT [poly(3,4-ethylenedioxythiophene)] powder soluble in common organic solvent were synthesized by oxidative polymerization of EDOT (3,4-ethylene dioxythiophene) monomer using functional dopant, DEHSNa [sodium di(2-ethylhexyl)sulfosuccinate]. Transparent electrodes were made by spin casting of PEDOT/organic solvents on substrates. The electrode showed the transmittance < 90% in visible region and the surface resistance of> ${\sim}10^3\;ohm/{\square}$, respectively.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.2
• /
• pp.238-241
• /
• 1987

ITO thin film was prepared by the electroless deposition technique. ITO thin film had a high transmittance in the visible region and a high reflectance in the near infrared region. The energy gap of the thn film (Sn/Im=0.1) was 4.05 eV, the carrier concentration was 2x10**21 cm**-3, and the electric resistivity was 1.5x10**-3 ohm-cm. We confirmed that ITO thin film was a degenerated n-type semiconductor.

• Journal of Information Display
• /
• v.7 no.3
• /
• pp.23-26
• /
• 2006

We fabricated top emission organic light emitting diode (TEOLED) with transparent metal cathode Barium and Silver bilayer. Very thin Ba/Ag bilayer was deposited on the organic layer by thermal evaporation. This cathode showed high transmittance over 70% in visible range, and the device with a Ba-Ag has a low turn on voltage and good electrical properties.

• Journal of the Korean Ceramic Society
• /
• v.27 no.6
• /
• pp.783-789
• /
• 1990

Shaped crystal growth apparatus were made for sapphire ribbon single crystal growth. Sapphire ribbon single crystal are grown by EFG(Edge-defined Film-fed Growth) methdo for use as watch-glass and SOS(Silicon-On-Sapphire) devices. Sapphire ribbon crystals were grown to be 40min wide, 1.8mm thick, 96mm long. Therelationshiops between growth striation and surface roughness, with various growth rates, were investigated and compared. It was found that sapphire ribbon crystal is suitable for watch-glass by measuring the transmittance in the visible light region.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.3
• /
• pp.340-348
• /
• 2013

In Projection Stereolithography Apparatus (PSLA), Digital Micromirror Device (DMD) and Liquid Crystal Display (LCD) are used as a beam pattern generator. The DMD shows high resolution, but it is mostly applied in micro stereolithography due to high cost and fabricable area. In LCD, the size of pattern beam is freely controlled due to various panel sizes. The LCD, however, has some limitations such as short life time by the high power light source, non-uniform light intensity of pattern beam and low transmittance of UV-light. To solve these problems in LCD-based PSLA, a Scanbeam-SLA with LCD of 19 inches and visible LED-array is developed. In this system, the light module works like a scanner for uniform illumination. The system configuration, working principle and fabrication examples are addressed in this study.