• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.401-408
• /
• 2005

Recently shield TBM tunnellings are being applied to subway construction in Korean cities. Generally these kinds of tunnellings have the problems in the stability of ground such as subsidence because urban subway is constructed in the shallow depth. A sinkhole occurred on the road just above the tunnel during tunneling in Kwangju, so a survey for upper layer of the tunnel was needed. But conventional Ground Probing Radar can't be applicable due to the presence of steel-mesh screen in the shield segment, so no existent geophysical method is applicable in this site. Because the outer surface of each shield segment is electrically insulated, dipole-dipole resistivity method which is popular in engineering site investigation, was tried to this survey for the first time. Specially manufactured flexible ring-type electrodes were installed into the grouting holes at an interval of 2.4 m on the ceiling. The K-Ohm II system which has been developed by KIGAM and tested successfully in many sites, was used in this site. The system consists of 1000Volt-1Ampere constant-current transmitter, optically isolated 24 bit sigma-delta A/D conversion receiver - maximum 12 channel simultaneous measurements, and graphical automatic acquisition software for easy data quality check in real time. Borehole camera logging with circular white LED lighting was also done to investigate the state of the layer. Measured resistivity data lack of some stations due to failing opening lids of holes, shows general high-low trend well. The dipole-dipole resistivity inversion results discriminate (1) one approximately 4 meter diameter cavity (grouted but incompletely hardened, so low resistivity - less than $30{\Omega}m$), (2) weak zone (100-200${\Omega}m$), and (3) hard zone (high resistivity - more than 1000${\Omega}m$) very well for the distance of 320 meters. The 2-D inversion neglects slight absolute 3-D effect, but we can get satisfactory and useful information. Acquired resistivity section and video tapes by borehole camera logging will be reserved and reused if some problem occurs in this site in the future.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.624-627
• /
• 2014

In vehicular network, the basic goal is to provide vehicle safety service and commercial service such as ITS(Intelligent Transportation System) or video, etc on the road. And most research concentrated on transportation of safety message in congestion situation. It is important to allocate channel for safety message in congestion situation, but providing suitable service is also important problem in vehicular network. For this reason, IEEE 1609.4 allocate 4 multiple service channels (SCHs) for non-safety data transfer. But, in congestion situation with many vehicles, the contention for channel acquisition between services becomes more severe. So services are provided improperly because of lack of service channel. This paper suggests dynamic channel allocation algorithm. The proposed algorithm is that RSU(RaodSide Unit) maintain and manage the information about service and status of channels. On based of the SJF(Shortest Job First) scheduling using those information, RSU selects the most appropriate channel among the 4 SCHs allocated by IEEE 1609.4 in network congestion situation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.175-178
• /
• 2009

H.264/AVC is a video coding standard of ITU-T and ISO/IEC, and widely spreads its application due to its high compression ratio more than twice that of MPEG-2 and high image quality. In this paper, we explained Intra Prediction in H.264/AVC, which is able to achieve higher compressing efficiency from correlation removal of adjacent samples in spatial domain, and proposed efficient Intra Predictor architecture design for H.264/AVC decoder. The proposed system reduced computation cycle using processing element and precomputation processing element and also reduced the number of access to external memory using efficient register. We designed the proposed system with Verilog-HDL and verified with suitable test vector. The proposed Intra Predictor achieved about 60% cycle reduction comparing with existing Intra Predictors.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.258-263
• /
• 1995

미래 정보와 시대에서 중추적인 역할을 할 광관련 멀티미디어 장비들은 최근 관련 산업계에서 주목을 받기 시작하고 있고 특히 기존 VTR(Video Tape Recorder) 시장을 대체할 차세대 DVDR(Digital Video Disk Recorder)는 기술전쟁이라고 할 정도로 선진 기업의 연구가 치열해지고 있다. DVDR 시스템에서는 필요한 정보들을 레이저빔을 이용한 광학신호로 바꾸어 광디스크에 기록, 재생하는 광픽업이 절대적으로 필요하게 된다. 그런데 광픽업의 위치추종기구인 Actuator는 정확한 위치추종(.+-.1.$\mu$m 오차이내)을 할 수 있는 성능이 요구되며 서보의 특성상 20KHz 이하에서 불필요한 모우드가 가진되지 않는 정밀부품이어야 하므로 Actuator 각 부품의 동적인 특성을 명확히 규명할 필요가 있다. 따라서 본 연구에서는 우선 Actuator 각 부품과 가동부 전체의 중량 및 진동해석을 통해 동특성을 조사하였다. 그리고 Actuator의 중요한 기본성능중 하나인 구동감도 확보여부를 검토할 필요가 있기 때문에 유한요소법 프로그램인 ANSYS를 이용하여 자기회로 부분에 대한 해석을 구하였다. 또한 가동부와 자기회로 등 하위부품을 조립하는 과정에서 발생하는 조립오차로 인해 불필요한 공진과 회전형상이 야기될 수 있으므로 동특성 및 문제점 파악을 위한 민감도 분석이 필요하다. 따라서 본 연구에서는 가동부의 관성 모멘트 값과 강체에 대한 일반식을 이용한 자체 프로그램을 작성하여 조립공차를 구하였다. 이와같은 과정을 통해 구해진 설계값을 바탕으로 실제 제작된 Actuator에 대해서는 비접촉식 측정방법을 통해 동특성값을 측정하였고 이를 해석값과 상호 비교하였다.동강성행렬법(dynamic stiffness matrix method)을 이용하여 해석하고자 한다. 수준임이 입증되었다. 본 연구의 결과를 토대로우리나라 젊고 건강한 남성에게 적합한 무게상수는 작업자군에 대하여 25.05kg, 학생군에 대하여 20.24kg 으로 나타나 이는 미국 NIOSH 안전기준과 대체로 일치함을 발견하였다.ive structures utilized in Client/server architecture for distribution and cooperative processing of application between server and client this study presents two different data management methods under the Client/server environment; one is "Remote Data Management Method" which uses file server or database server and. the other is "Distributed Data Management Method" using distributed database management system. The result of this study leads to the conclusion that in the client/server environment although distributed application is assumed, the data could become centralized (in the case of file server or database server) or decentralized (in the case of distributed

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.1021-1023
• /
• 2013

Currently, aircraft and automobile simulator for training provides a variety of training by making hypothetical situation on a simulator Installed on the ground Currently. And the instructor maximizes the effectiveness of the training by Monitoring training and instructing the required training. When trainees are boarding the aircraft or automobile. The Instructor in the ground is not able to monitoring aircraft, automobile. The assessment of the training is not easy after the end of the training Therefore, it is difficult to provide high quality of education to the students. In this paper, Simulation software is to develop the following. Collecting GPS and real-time information for aircraft, automobile ${\grave{a}}implementing$ 3D simulation. Implementing Current image of the aircraft or automobile in the screen by 3D Real-time monitoring of training situation at the control center utilizing for training saving 3D video files Analysis, evaluation on training After the end of the training.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.602-609
• /
• 2020

In the event of a large-scale disaster such as an earthquake, typhoon, landslide, and building collapse, the disaster situation awareness and timely disaster information sharing play a key role in the disaster response and decision-making stages for disaster management, such as disaster site control and evacuation of residents. In this paper, an exited field investigation system of NDMI (National Disaster Management Research Institute) was enhanced with an LTE-VPN- based wireless communication system to provide an effective on-site response in an urgent disaster situation and share observation data or analysis information acquired at the disaster fields in real-time. The required performance of wireless communication for the disaster field investigation system was then analyzed and evaluated. The experimental result for field data transmission performance of an advanced wireless communication investigation system showed that the UDP transmission performance of at least 4.1Mbps is required to ensure a seamless video conference system between disaster sites. In addition, a wireless communication bandwidth of approximately 10 Mbps should be guaranteed to smoothly share the communication and field data between the survey equipment currently mounted on the survey vehicle.

• Proceedings of the Korea Contents Association Conference
• /
• 2006.11a
• /
• pp.824-828
• /
• 2006

Introduction of motion capture system to the field of digital entertainment paved the way to accelerate the development of 3D character animation all the more. Motion capture system has been developed of the level that it can capture the fierce motions of character particularly in the digital game image and improve the dynamic characteristics by capturing the movement of human muscle or express the human's true emotion by capturing wrinkles and expression on face. Such an extension of realistic expression enables them to be used increasingly in movie, TV, advertisement, music video, etc centering around the game industry in the field of digital entertainment. The fact is, however, that many difficulties are held in the image production process compared with the competing countries such as USA and Japan, owing to inferiorities in technical expertise and capital in the image production process using the local motion capture, insufficient professional human resources of motion capture and small size of local motion capture image market. Hence, this study intends to suggest the plan to improve the technical problems in terms of integrated motion capture system, motion capture professional human resources and motion capture in-house program development in the production process of digital entertainment image using the motion capture system by surveying local and overseas examples of image production.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2005.04a
• /
• pp.59-63
• /
• 2005

Respiration motion causes movement of internal structures in the thorax and abdomen, making accurate delivery of radiation therapy to tumors in those areas a challenge. Accounting for such motion during treatment, therefore, has the potential to reduce margins drawn around the clinical target volume (CTV), resulting in a lower dose to normal tissues (e.g., lung and liver) and thus a lower risk of treatment induced complications. Among the techniques that explicitly account for intrafraction motion are breath-hold, respiration gating, and 4D or tumor-tracking techniques. Respiration gating methods periodically turn the beam on when the patient's respiration signal is in a certain part of the respiratory cycle (generally end-inhale or end-exhale). These techniques require acquisition of some form of respiration motion signal (infrared reflective markers, spirometry, strain gauge, thermistor, video tracking of chest outlines and fluoroscopic tracking of implanted markers are some of the techniques employed to date), which is assumed to be correlated with internal anatomy motion. In preliminary study for the respiratory gating radiation therapy, we performed to measurement of this respiration motion signal. In order to measure the respiratory motion signals of patient, respiration measurement system (RMS) was composed with three sensor (spirometer, thermistor, and belt transducer), 4 channel data acquisition system and mobile computer. For two patients, we performed to evaluation of respiratory cycle and shape with RMS. We observed under this system that respiratory cycle is generally periodic but asymmetric, with the majority of time spent. As expected, RMS traced patient's respiration each other well and be easily handled for application.

• Journal of Korea Multimedia Society
• /
• v.6 no.2
• /
• pp.340-351
• /
• 2003

We introduce our experiences of the design and implementation of the Page Together system that has expanded hyperlink metaphor to utilize human resources in the web. This system supports that a user connects with others in the web, communicates through video/audio channel, navigates same web pages simultaneously and cooperates some work on Internet. For these functions, it comprises Collaborative Browsing Module (CBM), Multimedia Conferencing Module(MCM) Data Conferencing Module(I)CM) and Multi Protocol Interface(MPI). We adopted three standard protocols, IEC, H.323 and T.120 for each nodule and it allows developers to use them easily. We also defined MPI to synchronize information of session among modules. Each module exchanges information each other in session creating process and session terminating process. After a session is created once, each module works independently as its won protocol. Interferences among modules are reduced as minimizing to exchange information. We also introduce a web site that provides web board service based on the Page Together system. A user may post a notice with a link to himself/herself on our web board. After then, if someone read that notice and has any question about it, he or she can try to connect to the writer as clicking the link in that notice and communicate each other. This service site shows that our system can be applied to diverse internet services such as distance teaming and distance conference.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.581-584
• /
• 2009

Recently, the cameras which used for observation are installed in children protection area and local crime prevention area in order to protect life and property and by its work being recognized and are installed more. Normal cameras have cost problem to observe multiple area and detail, because they can observe only one place. PTZ camera can observe multiple area by moving focus by schedule or remote control, but it can't automatically move the focus of it to the place where event occurred, because it can't recognize the place. In this study, we can monitor multiple area effectively, by installing a wireless sensor node equipped with temperature, lighting, gas and human detection sensor to each area, to monitor many place low-price and actively and to move the focus of PTZ camera to preset position, and send recorded video to the user, when the various sensor data received from wireless sensors in observation area are to be determined abnormal by analyzing. In addition, at night we can record a scene using infrared, but to reduce power consumption of lighting system which are installed to improve resolution, it supplies power to the lighting system when event occurred. So we were able to implement low power green monitoring system.