• 제어로봇시스템학회논문지
• /
• 제20권8호
• /
• pp.795-800
• /
• 2014

In this paper, a vibrotactile pad system, T-mobile, is developed to provide vibrotactile cues for hand-held devices. A grooved and slim design is adapted to the back-side plane of the T-mobile, and the contact part consists of 12 vibrotactile panels which can operate independently and separately. To be isolated among vibrotactile actuators, the surface of the cover is divided into several pieces. Each vibrating module consists of a linear resonant actuator, a section of covering surface, and a vibration isolator. In order to provide spatial and directional information, sensory saltation and phantom sensation are applied to the T-mobile. To evaluate the developed device, two experiments were conducted to test whether directional information and spatial information can be successfully displayed by the device. Additionally, in order to find optimal stimulation by sensory saltation, an empirical test was conducted. As a result, spatial and directional information would be useful for displaying intuitive information for hand-held devices with vibrotactile feedback and reasonable near-optimal value for sensory saltation was obtained.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.904-907
• /
• 2002

Optical disk drive device is improved in rotating speed for faster data reading. In the case of CD-ROM, rotating speed is over 10000 rpm in the practical use. As a result of high rotating speed, unexpected effects as like increasing disk fluctuation and acoustic noise are raised by the air friction on the rotating disk and the eccentricity of rotating parts. The overall acoustic noise of running CD-ROM could be classified into two different characterized noise. The first is the structural-borne noise which is generated from vibrating solid body. By the reason, the signal of structural borne noise has very similar to the signal of surface vibrating one. It has dense noise energy at specific frequency region. The other is the air-borne noise which is generated from turbulence or vortex caused by friction between disk and air. The signal of air-borne noise has no dominant peak point at acoustic pressure-frequency domain. The noise energy is widely distributed while comparatively high and large frequency region. The structural-borne noise could be reduced by reducing vibration of structure and in addition it's target reducing frequency is narrow. However the air-borne noise reduction is effectively needed of enclosing method for the noise source located near the disk surface because it is difficult to define target frequency point. In this study, the acoustic noise at driving CD-ROM is classified by the sides of it's character and tried to reduce the overall acoustic noise.

• 자원리싸이클링
• /
• 제31권6호
• /
• pp.36-43
• /
• 2022

순환골재 입도 분리를 위해 사용되는 일반적인 스크린은 막힘 현상으로 인해 함수 시료 처리가 제한적이다. 따라서 본 연구에서는 기존 스크린의 분리 효율을 개선하기 위하여, DEM(Discrete Element Method) 기반의 모사 실험을 통해 스프링 기반의 추가 보조 진동 장치의 우수성을 판단하였다. 스프링 디자인에 따른 변위, 진폭 및 변형 각 분석을 통해 운동 특성을 확인하였으며, 이를 스크린에 적용하여 입자의 거동을 모사하였다. 입자 모사 결과, 스프링이 적용된 스크린의 물질 흐름 및 분리 효율은 각각 9.2 kg/s, 97 %로 나타났으며, 기존 스크린과의 비교를 통해 막힘 방지 스프링의 적용은 기존 스크린을 개선할 수 있음을 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.263-263
• /
• 2007

In the future, self-contained sensors and processing units will need on-board, renewable power supplies to be truly autonomous. One way of supplying such power is through energy harvesting, processes by which ambient forms of energy are converted into electricity. One energy harvesting technique involves converting kinetic energy, in the form of vibrations, into electrical energy through the use of piezoelectric materials. Researchers are currently investigating how piezoelectric materials can be used to harvest power. This study examines the use of auxiliary structures, consisting of a mechanical fixture and a lead zirconate/lead titanate (PZT) piezoelectric element, which can be attached to any boundary conditions vibrating beam of the any boundary conditions. Adjusting various boundary conditions of these structures can maximize the strain induced in the attached PZT element and improve power output.

• 전기학회논문지
• /
• 제56권7호
• /
• pp.1218-1223
• /
• 2007

A surface micro machined angular rate sensor utilizing a vibrating MEMS structure on a silicon has been developed. These tuning fork angular rate sensors are extremely rugged, inherently balanced, and easy to fabricate. The device is fabricated using a temperature compensation method based on automatic gain control technique. A linearity of approximately 0.6%, limited by the on-chip electronics has been obtained with this new sensor. Tests of the sensor demonstrate that its performance is equivalent to that required for implementation of a yaw control system. Vehicle handling and safety are substantially improved using the sensor to implement yaw control.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.132-137
• /
• 2003

For the evaluation of acoustic noise of a DLP projector, vibration and sound characteristics of a DLP projector were studied. The acoustic noise of DLP projector could be classified into three categories, that is, the direct noise from a body of rotation, the air-bone noise generated from turbulence or vortex occurred during cooling process and the structural born noise produced by vibrating elements. Cooling fans and color filter wheel which rotates at 9000 rpm are main causes of acoustic noise induced in DLP projector. Since the structure of an optical module in a DLP projector can be excited by the excessive vibration of a color filter wheel, the structural design for anti-vibration should be considered. To make a reduction of overall acoustic noise, the anti-vibration design and the enclosing structure have been studied and applied to a color filter wheel.

• 한국산업융합학회 논문집
• /
• 제16권4호
• /
• pp.133-140
• /
• 2013

This paper presents an overview of the concepts of optimal feeder design in relation to the loading of bulk solids for Automatic filling system that should be control the amount of goods and packaging to seal. Feeder modular device, important parts of the package, so in order to perform a conceptual design optimization techniques are applied in two steps. First of all derive the problems through structural analysis for the conceptual model of vibrating feeder. Secondly derive reasonable design model based on the results of the structural analysis of modified boundary shape and then verify it. The proposed system has the following goal that is satisfies the dynamic stability with minimum weight and optimization of the shape. As a result, the weight reduction of feeder is 2.1% and 7% increase in the natural frequency.

• Journal of Magnetics
• /
• 제16권4호
• /
• pp.413-416
• /
• 2011

An array of FeCo nanotubes has been successfully fabricated in the pores of porous anodic aluminum oxide (AAO) templates by wetting templates method. The morphology and structure of the nanotube array were characterized by scanning electron microscopy, transmission electron microscopy and x-ray diffraction. The average diameter of the nanotubes was about 200 nm, and the length was more than 10 ${\mu}m$. Vibrating sample magnetometer and superconducting quantum interference device were used to investigate the magnetic properties of the nanotube array. Interaction between the nanotubes has been found to be demagnetizing as expected and the switching field distribution is broad.

• 한국소음진동공학회논문집
• /
• 제14권9호
• /
• pp.861-867
• /
• 2004

For the evaluation of acoustic noise of a DLP projector, vibration and sound characteristics of a DLP projector were studied. The acoustic noise of DLP projector could be classified into three categories, that is, the direct noise from a body of rotation, the air-bone noise generated from turbulence or vortex occurred during cooling process and the structural born noise produced by vibrating elements. Cooling fans and color filter wheel which rotates at 9000 rpm are main causes of acoustic noise induced in DLP projector. Since the structure of an optical module in a DLP projector can be excited by the excessive vibration of a color filter wheel, the structural design for anti-vibration should be considered. To make a reduction of overall acoustic noise, the anti-vibration design and the enclosing structure have been studied and applied to a color filter wheel.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.259-262
• /
• 2005

The large transformers used in the electric power company become targets of public complaints because of those characteristics generating high-level noise. Reducing vibration level is the basis of noise control for the large transformers. For this reason, a vibrating reducing element is developed for the large transformers with a sub-element enduring seismic movement. Large attenuation of vibration is achieved by applying the element to the large transformers in a substation.