• 대한기계학회논문집B
• /
• 제24권6호
• /
• pp.870-879
• /
• 2000

An experimental investigation is conducted to improve a slot film cooling system which can be used for the cooling of gas turbine combustor liner. The tangential slots are constructed of discrete holes with different injection types which are the parallel, vertical, and combined to the slot lip. The investigation is focused on the coolant supply systems of normal-, parallel-, and counter-flow paths to the mainstream direction. A naphthalene sublimation technique has been employed to measure the local heat/mass transfer coefficients in a slot with various injection types and coolant feeding directions. The velocity distributions at the exit of slot lip for the parallel and vertical injection types are fairly uniform with mild periodical patterns with respect to the hole positions. However, the combined injection type increases the nonuniformity of flow distribution with the period equaling twice that of hole-to-hole pitch due to splitting and merging of the ejected flows. The secondary flow at the lip exit has uniform velocity distributions for the parallel and vertical injection types, which are similar to the results of a two-dimensional slot injection. In the results of local heat/mass transfer coefficient, the best cooling performance inside the slot is obtained with the vertical injection type among the three different injection types due to the effect of jet impingement. The lateral distributions of Sh with the parallel- and counter-flow paths are more uniform than the normal flow path. The averaged Sh with the injection holes are $2{\sim}5$ times higher than that of a smooth two-dimensional slot path.

• 한국콘텐츠학회논문지
• /
• 제7권7호
• /
• pp.24-30
• /
• 2007

본 논문에서는 T형 슬롯을 삽입한 정삼각형 패치 안테나의 특성을 관찰하였고, 정삼각형 패치 내부에 얇은 가로 또는 세로 슬롯을 삽입하였을 때, 슬롯의 변화에 따른 이중 공진 주파수의 변화를 관찰하여 유전체의 높이가 매우 낮은 기판에 적합한 T형 슬롯을 삽입한 정삼각형 패치 안테나를 제안하였다. 제안된 안테나는 ${\epsilon}_r=3.38$, 유전체의 높이가 8[mils] (=0.2032mm)인 기판을 사용하였고, 비교된 가로와 세로 슬롯의 안테나의 특성은 앙상블8.0 시뮬레이터를 이용하여 비교하였으며, 제작된 안테나의 이론적, 실험적 결과들이 비교되었다.

• 한국농공학회지
• /
• 제10권1호
• /
• pp.1377-1387
• /
• 1968

In order to measure runoff and soil losses produced in a small test plot during rainfall, it is usually insufficient to use a tank only, necessitating the combined use of a main tank and a subsidiary tank. Accordingly. exact measurement largely depends on how to connect those two measuring tanks. The main purpose of this thesis is to improve the connecting parts of two measuring tanks so as to assure exact measurement of runoff and soil losses. In this experiment, two types of main tank, i. e. A-type and B-type, were used. A-type is a square tank having a flume at its end. At the flume, ten apertures are provided by using metal columns so as to be able to catch one tenth of total muddy flow discharging at the end of the flume, One tenth of total flow is led to the subsidiary tank through a slot sampler fixed to an aperture. B-type differes in that its flume does not have apertures and slot sampler is fixed directly to the end of the flume, other features being the same as those of A-type. Discharge volumes were measured by using weighing tanks and compared. The effect of baffle screen provided in the flume was also observed in connection with exact measurements. In order to keep main tank and its flume in a horizontal position, bolts and nuts mechanism was used. Vertical and horizontal screens were provided in the main to prevent coarse sands coming into the flume. The conclusion derived through this experiment is as follows: (1) The discharge through slot sampler at each aperture is almost the same for A-type. However, it is slightly more than one tenth of total discharge volume. (2) In case that baffle screen is provided in the flume of A-type tank, the discharge volume of slot sampler is less than that of the same type without screen. (3) For B-type tank, slot sampler discharge increases as slot sampler nears toward the center of flume. (4) When baffle screen is provided in the flume of B-type, slot sampler discharge is less than that of the same type without screen, and this phenomenon is more apparent as compared with A-type. (5) In case that the slot width of slot sampler for B-type is one inch, slot sampler discharge exceeds one tenth of total discharge volume. (6) When the slot width for B-type is 15/16 inch and slot sampler is fixed 3/8 inch apart from either flume wall, slot sampler discharge is approximately equal to one tenth of total discharge volume.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.435-435
• /
• 2010

A inclined slot-excited plasma source is newly designed and constructed for higher flux HNB(Hyperthermal Neutral Beam) generation. The present source is different from the vertical SLAN(SLot ANtenna) sources [1] in two aspects. One is that the slots are inclined, and the other is that the magnetic field is configured to a cusp type. These modifications are intended to make the source plasma operated in sub-milli-torr pressure regime and as thin as possible, both of which is to get higher HNB flux by decreasing the re-ionization rate of the reflected atoms from the neutralizer [2]. The plasma is generated in a quartz tube of internal diameter 170 mm enclosed in a aluminum application chamber of larger diameter 250 mm. The microwave power is fed to the plasma chamber by 8 inclined slots cut into the application chamber wall. The slots are coupled the chamber to a WR280 waveguide wound around it to form a ring resonator. In order to make two slots $\lambda_g/2$ apart in phase, the adjacent slots are rotated in opposite directions. The rotation angle of the slots are set to $60^{\circ}$ from the chamber axis. Between the quartz chamber and the aluminum cylindrical chamber 8 NdFeB magnets are equally spaced and fixed to form the cusp magnetic field confinement and ECR (Electron Cyclotron Resonance) field. In this presentation, the magnetic and electromagnetic simulations, and the measured plasma parameters are given for both the inclined and the vertical slot-excited plasma sources. We also discuss how the sources can be tailored to suit better-performing HNB sources.

• 한국환경복원기술학회지
• /
• 제19권4호
• /
• pp.61-79
• /
• 2016

This study aims at examining the structural and managemental problems of the existing fishways which affect the migrations of fishes, and at suggesting alternatives to improve the fishways' efficiency. The study focuses on the fishways constructed in the diversion weirs in the lower reaches of 41 rivers(2 national rivers and 39 rural rivers) in the eastern coast of Korea. Most of water-using facilities in Korean rivers are diversion weirs, and fishways are established as subsidiary facilities of most of the weirs. Among the 58 or so fishways examined in this study, only a few are doing their proper function, and most of them need improvement. This study aims at strengthening those fishways function and increasing their economic efficiency and migration efficiency. Based on the results of this study, the followings are suggested. In case the fishway sticks out downstream from the apron, a subsidiary fishway diverging from the main is suggested to attract fish. The entrance to the subsidiary should head below the raised part of the apron and a pool should be constructed in the connecting part with the main. To attract fish and let the upstream migrators rest for a while, an entrance pool should be constructed in the fishway. Most of the examined fishways have low side walls, which allow the upstreamers to jump out of the fishway. Those side walls are suggested to be raised above the jumping height of target fishes. The exit parts of most fishways are too shallow, or have no grass to protect the fish from the birds. Protective facilities are suggested to keep the birds from entering the fishway. By the time Ice-harbor type and Vertical-slot type fishways are scientifically proved to be defective, the fishway should not diverge from the standard design.

• Architectural research
• /
• 제10권1호
• /
• pp.33-39
• /
• 2008

Condensation has mainly occurred in corridor type apartment door which is exposed to the outside air and is made of steel, which has high thermal conductivity. As a result, the total costs of repair have increased with the number of disputes with residents. In this study, therefore, we investigate materials and construction methods used in apartment door, perform a computer simulation to find out possible improvements, and then suggest the dew point to prevent the occurrence of condensation throughout simulation. The results indicate that the temperature that condensation does not occur is $15.4^{\circ}C$, and the optimum method of achieving this dew point is shown to be a door frame system including a large vertical slot to decrease the area of thermal conduction between the outer and inner portions of the door frame. Mock-up tests show that the surface temperature of the door frame was higher than the dew point, and the system can withstand severe cold conditions of $-20^{\circ}C$. In application test, the surface temperature of door frame with vertical slots is $5.9^{\circ}C$in average, which is higher than the existing door frame. Furthermore, in the temperature distribution of the surrounding door measured with infrared ray camera, the existing door shows the high temperature distribution indicating lack of insulation, but the improved door shows the low temperature distribution indicating higher insulation.

• Geomechanics and Engineering
• /
• 제37권5호
• /
• pp.431-441
• /
• 2024

A newly developed line-style sand pluviator has been calibrated to prepare repeatable sand specimens of specific statuses of compactness and homogeneity for laboratory tests. Sand is falling via a bottom slot of a fixed hopper, and by moving the sample container under the slot, the container is evenly filled with sand. The pluviator is designed with high flexibility: The falling height of sand, the hopper's opening width and the relative moving speed between the hopper and the sample box can be easily adjusted. By changing these control factors, sand specimens of a wide range of densities can be prepared. A series of specimen preparation was performed using the coarse Merwede River sand. Performance of the pluviator was systematically evaluated by exploring the alteration of achievable density, as well as checking the homogeneity and fabric of the prepared samples by CT scanning. It was found that the density of prepared coarse sand samples has monotonic correlations with none of the three control factors. Furthermore, CT scanning results suggested that the prepared samples exhibited excellent homogeneity in the horizontal direction but periodical alteration of density in the vertical direction. Based on these calibration test results, a preliminary hypothesis is proposed to describe the general working principles of this type of pluviators a priori, illustrating the mechanisms dominating the non-monotonic correlations between control factors and the relative density as well as the vertically prevalent heterogeneity of specimens. Accordingly, practical recommendations are made in a unified framework in order to lessen the load of similar calibration work.

• 대한토목학회논문집
• /
• 제7권1호
• /
• pp.11-22
• /
• 1987

흐름수역(水域)에서 연직상향으로 방류되는 평면부력(平面浮力)?의 거동이 연속방정식(連續方程式), 운동량방정식(運動量方程式) 및 추적물수송식(追跡物輸送式)의 기본방정식을 수치적(數値的)으로 풀음으로서 해석(解析)된다. 난류확산(亂流擴散)에는 Prandtl의 혼합거리이론(混合距離理論)을 도입한 난류수송모형(亂流輸送模型)이 이용된다. 수치해과정(數値解過程)은 기본방정식을 유함수(流凾數)(stream function)식(式)과 골도수송(滑度輸送)(vorticity transport)식을(式) 이용하여 변환(變換)한 후, ?방류속도(放流速度), ?방류구폭(放流口幅) 등(等)으로 표현되는 변수(變數)와 흐름을 지배(支配)하는 무차원매개변수(無次元媒介變數)를 도입하여 무차원화(無次元化)하고 successive under-relaxation을 이용하여 Gauss-Seidal 반복법(反復法)으로 해를(解) 구(求)하는 것이다. 수치실험(數値實驗)은 방류(放流)Froude수(數)가 4~32, 방류속도(放流速度)와 가로흐름속도와의 비로(比) 정의되는 속도비가 8~15 의 범위의 흐름영역(領域)에서 수행되었다. 부력(浮力)?으로 인한 주변(周邊)흐름수역(水域)의 속도변화(速度變化), 온도상승(溫度上昇)범위, 흐름상태 및 골도(滑度)가 조사되었으며, ?의 경로에 대한 속도비와 방류밀도Froude 수의 영향이 또한 조사되었다. ?중심선의 속도, 온도변화, 국부밀도(局部密度)Froude 수(數)의 변화가 계산되며 퍼짐율(spreading rate)과 확산비(擴散比)(dispersion ratio)가 방류밀도(放流密度)Froude 수, 국부밀도(局部密度)Froude 수(數) 및 속도비(速度比)의 항(項)으로 해석되었다. 또한 속도와 온도분포를 상사(相似)(similarity)로 나타낼 수 있음이 밝혀졌으며, Gaussian 분포(分布)를 이용한 적분형해석(積分型解析)(integral type analysis)이 가능한 것으로 사료된다.

• 생태와환경
• /
• 제53권3호
• /
• pp.255-264
• /
• 2020

국내 주요 6개 하천의 보에 설치된 어도에서 2~9년 이상 매월 연속적이고 장기적으로 어류의 어도이용을 조사하였다. 어류의 어도 이용은 어도 출구부에서 trap에 의한 직접 채집 방법으로 조사하였다. 6개 지점의 어도를 이용하는 어류와 하천에 서식하는 어류의 군집구조는 차이를 보였다. 어류의 어도 이용은 대략 2~7종이 전체의 80% 이상을 차지하였다. 이것은 어류의 어도 이용이 종적 생리특성에 따라 특화된 결과로 보이며, 단순히 어도에서의 흐름에 따라 어도 이용을 유인하는 경우는 많지 않은 것으로 보인다. 또한, 6개 지점에서 어도 이용 어류의 분포는 하천의 위치 및 보에 설치된 어도형식에 따라 달랐다. 이러한 차이는 해양 및 하구로부터 이동한 회유종의 분포 여부에 의한 결과로 보인다. 또한, 어도형식에 따른 수리특성의 차이도 영향을 주었다. 대체로 어도 내부에서 상대적으로 빠른 유속을 보이는 버티컬슬롯식 어도에서 어도이용 종수가 적고 유영능력이 좋은 어류의 비율이 높았다. 어도를 이용하는 주요 어류의 분석결과는 어도 계획과 이를 위한 주요 대상종의 선정에 활용될 수 있을 것이다.

• 대한치과교정학회지
• /
• 제27권5호
• /
• pp.697-709
• /
• 1997

발치 환자의 치료에서 결과의 안정성과 심미적인 요구를 만족하기 위해서는 상악 전치의 전후방 및 수직적인 위치와 순설측 경사를 올바르게 설정하여야 한다. 상악 치열에서 제 1 소구치를 발거하고 견치를 발치 공간으로 후방이동시킨 상태에서, 호선을 이용하여 전치를 후방견인시킬 때 치아의 설측 경사와 정출과 같은 부작용이 일어날 수 있으므로 이를 방지하기 위해 다양한 방법으로 힘과 모멘트의 조절을 시도하여야 한다. 치관의 한 지점에 적용되는 힘의 크기와 모멘트의 비율에 따라 치근막에 나타나는 응력분포가 변화하고 이를 알아냄으로써 치아이동 양상을 예측할 수 있다. 상악 전치부에 직접 힘을 가하게 되는 J-hook headgear는 전치부의 모멘트를 변화시키는 효과를 제공하므로, 본 연구에서는 호선의 전치부에 각각 다른 토오크를 부여하고 각 상태에서 J-hook headgear를 후상방으로 적용하였을 때 모멘트 변화에 따른 응력분포의 변화를 광탄성법으로 관찰하였다. 치조골 부위를 광탄성 레진으로 대체한 모형을 제작하고 인공 치아에 .022" slot의 standard edgewise bracket을 부착하였다. 측절치 bracket 원심 1mm지점 에 높이 7mm의 vertical loop을 가지는 호선을 .020" $\times$ .025" stainless steel wire 로 제작하였으며 중절치와 측절치 사이에 high pull f-hook headgear를 위한 hook을 납착하였다. 전치부에서 $0^{\circ},\;7^{\circ},\;14^{\circ}$ 의 토오크를 각각 부여한 뒤, loop을 1mm activation하였을 때 나타나는 응력분포와 각각에 high pull J-hook headgear를 교합면에 대하여 후상방 $35^{\circ}$ 방향으로 200mg의 힘을 적용했을 때의 응력분포를 비교하였여 다음과 같은 결과를 얻었다. 결론 1. $0^{\circ}$ 토오크에서는 치근의 치근단측 1/2부위에 응력이 분포하였으나 순측에 비해 설측이 약하고 좁게 나타났고 특히 치근단에 집중된 응력은 순, 설측 모두에서 high pull J-hook headgear의 사용으로 감소하였다. 2. $7^{\circ}$ 토오크에서는 치근면을 따라서 응력이 분포하는데, 순측으로는 치조정에서부터 나타나는 응력이 치근면을 따라 서 치근단측 1/3부위까지 점차 폭이 좁아졌고, 설측은 순측보다는 약한 응력이 치근의 치관측 1/3에서부터 치근단까지 나타났다. 치근단에서는 순측보다 설측이 더 강하게 나타났고, high pull J-hook headgear의 사용으로 전반적으로 응력의 크기와 폭의 증가가 있었다. 3. $14^{\circ}$ 토오크의 호선에서는$7^{\circ}$ 토오크의 호선과 분포하는 응력의 양상은 유사하지만 좀 더 강하게 나타났고, 순측에서 는 치근면의 중앙부위가 폭이 가장 넓게, 설측에서는 순측에 비해 균일한 폭으로 응력이 분포하였다. 치근면을 따라서 나타나는 응력은 headgear를 사용하는 것이 사용하지 않은 경우보다 강하였고 순측보다는 설측이 더 강하였다. headgear를 사용하였을 때 치근단의 응력 집중은 순측에서보다 설측에서 더 크게 나타났다.