• Journal of Fisheries and Marine Sciences Education
• /
• v.23 no.4
• /
• pp.662-672
• /
• 2011

This study was investigated to obtain basic data which can be applied to processing of canned seasoned kwamaegi. Commercial Kwamaegi was cut into $2{\times}3cm$ lengths, filled 90 g into can (301-3) and added with 60 g water before precooking for 10 min. at $100^{\circ}C$. The precooked Kwamaegi was packed into the can, and added with 60 g seasoning sauces, which was prepared by mixing soy sauce 23%, monosodium glutamate (MSG) 2%, sorbitol 2%, sesame oil 1%, vinegar 2%, starch syrup 17%, sake 5%, water 48%. The cans were sealed using a vacuum seamer and then sterilized for various Fo values (Fo 8~12 min.) in a steam system retort at $121^{\circ}C$. The factors such as pH, VBN, amino-N, total amino acid, free amino acid, color value (L, a, b), texture profile, TBA value, mineral, sensory evaluation and viable bacterial count of the canned seasoned Kwamaegi produced with various sterilization condition(Fo 8~12 min.) were measured. There was no remarkable difference between sterilization conditions and sensual characteristics. The results showed that the product sterilized at Fo 8 min. was the most desirable because this condition is most economical.

• Analytical Science and Technology
• /
• v.22 no.2
• /
• pp.141-147
• /
• 2009

A laser induced breakdown spectroscopy (LIBS) measurement was carried out to derive an optimized measurement condition with a high reproducibility and to grow a plasma sphere to 20 mm high under a 600 mtorr vacuum in order to improve an accuracy of measurement. The measurement of the plasma was taken at a 6.0 mm distance, in the direction of a plasma sphere, from a sample. This location belongs to the outer sphere region in the plasma. The calibration curve of 'Ni' and 'Cu' was acquired by the signal intensity ratio and the atomic ratio for the samples, and linear regression of 'Cu' was $R^2$=0.9886, and the linear regression of 'Ni' was $R^2$=0.9988. The accuracy of LIBS was improved pre-existence as the measurement error of 'Ni' was 0.78%.

• Horticultural Science & Technology
• /
• v.32 no.6
• /
• pp.864-871
• /
• 2014

Seed viability is affected by storage conditions and rapid loss of viability in storage is the major cause for low germination. This study was carried out to examine the effect of packaging materials and storage temperature on seed germination rate over 10 years in two species (Capsicum annuum L. and Brassica rapa L. ssp. pekinensis) and determine effective storage conditions for maintaining seed viability. Seeds were packaged in aluminum poly pouches under vacuum, polyethylene bottles, and paper bags containing silica gel and stored under one of two controlled conditions ($15^{\circ}C$, RH 40% or $5^{\circ}C$, RH 30%) or at ambient condition. Seed germination was recorded at 6-month intervals for 10 years. The seeds of both species showed no decline in viability until 6.5 years at 15 or $5^{\circ}C$, irrespective of packaging materials. However, under ambient conditions, the seeds of chili pepper and Chinese cabbage in paper bags lost viability after 4 and 5 years, respectively. By contrast, seeds of both species in vacuum-aluminum poly pouches exhibited a 99% germination rate after 6 years under ambient conditions. Pepper seeds in the vacuum-aluminum poly pouches maintained a 93% germination rate after 10 years in ambient conditions. These results indicated that a special seed storage facility for maintaining viability of chili pepper and Chinese cabbage seed might not be essential and seed testing would not be necessary for 10 years, if chili pepper and Chinese cabbage seeds were packed in ambient/vacuum-aluminum poly pouches or $5^{\circ}C$/vacuum-aluminum poly pouches.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.6
• /
• pp.691-699
• /
• 2014

In order to improve the dimensional stability and durability of wood, this study attempted to impregnate bismuth (Bi) - tin (Sn) alloy metal with low melting temperature into solid woods of three species such as radiata pine, red oak and white oak, and investigated to determine an optimum condition of manufacturing the metal alloy-wood composites with natural wood grains. These Bi-Sn alloys were chosen for this study because they were harmless to human and melting at low temperatures. The composites resulted in high dimensional stability and low thickness swelling, and also showed much improved performance such as high bending strength, high hardness, high electric conductivity, and high thermal conductivity as floor materials. A proper impregnating condition of all specimens was determined as 10 minutes of the preliminary vacuum time, and $185^{\circ}C$ of the heating temperature. The proper processing condition for radiata pine wood was 2.5 minutes of the pressuring time at the pressure of $10kgf/cm^2$. For red oak wood, 10 minutes of the pressuring time at the pressure of $30kgf/cm^2$ were the proper condition. The proper manufacture conditions for white oak wood was determined as 10 minutes of the pressuring time at the pressure of $50kgf/cm^2$.

• Journal of the Korean Institute of Gas
• /
• v.20 no.6
• /
• pp.37-42
• /
• 2016

The purpose of this paper is to study for the emission gas control of passenger car. The first example, the PCSV never open when operating condition, but it opened by causing malfunction because of trouble. As a result, the purge gas entered into surge tank, a mount of fuel was displayed with excessive supply on tester. Therefore, it certified the bad-condition of the engine when idling by decreasing of fuel injection quantity from engine ECU. The second example, the hose activating a EGR valve didn't supply the vacuum pressure because of assembling the other part. Thus, it knew the bad-condition of engine that the EGR valve would not work normally by leaking with the other port. The third example, as the rear oxygen sensor of two sensor were fault-installing by changing the sensor of other a car it could not detect of oxygen quantity. Finally, it found the phenomenon of abruptly decreasing vehicle speed when braking a car. Therefore, the system including with emission control has to drastically manage by maximizing condition to role decreasing the emission gas.

• Journal of Sericultural and Entomological Science
• /
• v.53 no.2
• /
• pp.87-91
• /
• 2015

There is no specific data on Entomogenous fungus (DongChungHaCho) in accordance with the silkworm varieties, despite of very high value industrial use as functional materials at domestic and abroad. In this study, we investigated culture condition and characteristics of Paecilomyces tenuipes in 3 silkworm cultivars and 2 specific silkworm breeds. Infection rate of P. tenuipes for silkworm varieties was the highest Kumokjam, followed by Baegokjam, Daeseongjam, Golden silk, Yeonnokjam in that order. The optimum culture conditions were as follows: dark condition, $22^{\circ}C{\pm}1$, and about $4cm^2$ in planting density per pupa. Also, we have developed annual production technologies of P. tenuipes. First, in order that the moisture content of the infection pupa became 3% or less in the natural condition. Second, the dried pupa must be vacuum-packed and was kept under $4^{\circ}C$. Finally, by restoring the moisture content of the dried pupa and culture in optimal condition, the technique for annual production of the P. tenuipes was achieved. Therefore, we expect that the use of Kumokjam and annual production technique will contribute significantly to farm income.

• Journal of the Korean Magnetics Society
• /
• v.9 no.4
• /
• pp.210-216
• /
• 1999

The objective of this paper is to investigate corrosion behaviors of CoCrTa/CrNi thin film and post heat-treatment effect. An electron beam evaporator was used for films deposition. After evaporation, post heat-treatment was carried out under $5.0{\times}10^3$ Torr vacuum condition. Annealing temperature and time were 400 $^{\circ}C$ and 30 min, respectively. To understand the effect of annealing on corrosion behavior of CoCrTa/CrNi, potentiodynamic polarization technique and accelerated corrosion chamber test were undertaken. Corrosion potential is higher for the annealed samples (CoCrTa 400$\AA$/CrNi 1000$\AA$) than for as-deposited one. This is attributed to an enrichment of Cr in the surface layer of the thinfilm resulting in a more corrosion resistant material.

• Korean Journal of Materials Research
• /
• v.14 no.8
• /
• pp.600-606
• /
• 2004

$Zn_{2}SiO_{4}:Mn$ phosphor particles were prepared by a flame spray pyrolysis method. It has been generally known that the high-temperature flame enables fast drying and decomposition of droplets. In the present investigation, the morphology and luminescent property of $Zn_{2}SiO_{4}:Mn$ phosphor were controlled in a severe flame preparation condition. The particle formation in the flame spray pyrolysis process was achieved by the droplet-to-particle conversion without any evaporation of precursors, which made it possible to obtain spherical $Zn_{2}SiO_{4}:Mn$ particles of a pure phase from a droplet. Using colloidal solutions wherein dispersed nano-sized silica particles were adopted as a silicon precursor. $Zn_{2}SiO_{4}:Mn$ particles with spherical shape and filled morphology were prepared and the spherical morphology was maintained even after the high-temperature heat treatment, which is necessary to increase the photoluminescence intensity. The $Zn_{2}SiO_{4}:Mn$ particles with spherical shape, which were prepared by the flame spray pyrolysis and posttreated at $1150^{\circ}C$, showed good luminescent characteristics under vacuum ultraviolet (VUV) excitation.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.10a
• /
• pp.81-88
• /
• 2000

The elastic wave equation is solved using the finite-difference method in 3D space to simulate the seismic wave propagation. It is based on the velocity-stress formulation of the equation of motion on a staggered grid. The nonreflecting boundary conditions are used to attenuate the wave field close to the numerical boundary. To satisfy the stress-free conditions at the free-surface boundary, a new formulation combining the zero-stress formalism with the vacuum one is applied. The effective media parameters are employed to satisfy the traction continuity condition across the media interface. With use of the moment-tensor components, the wide range of source mechanism parameters can be specified. The numerical experiments are carried out in order to test the applicability and accuracy of this scheme and to understand the fundamental features of the wave propagation under the generalized elastic media structure. Computational results show that the scheme is sufficiently accurate for modeling wave propagation in 3D elastic media and generates all the possible phases appropriately in under the given heterogeneous velocity structure. Also the characteristics of the ground motion in an sedimentary basin such as the amplification, trapping, and focusing of the elastic wave energy are well represented. These results demonstrate the use of this simulation method will be helpful for modeling the ground motion of seismological and engineering purpose like earthquake hazard assessment, seismic design, city planning, and etc..

• Journal of Surface Science and Engineering
• /
• v.34 no.5
• /
• pp.384-390
• /
• 2001

The hollow cathode discharge is a kind of plasma formation scheme in which plasma is formed inside a hollow structure, the cathode, with current to a nearby anode of arbitrary shape. In this scheme, electrons reflex radially within the hollow cathode, establishing an efficient ionization mechanism for gas within the cavity. An existence condition for the hollow cathode effect is that the electron mean-free-path for ionization is of the order of the cavity radius. Thus the size of this kind of plasma source must decrease as the gas pressure is increased. In fact, the hollow cathode effect can occur even at atmospheric pressure for cathode diameters of order 10-100 $\mu\textrm{m}$. That is, the "natural" operating pressure regime for a "micro hollow cathode discharge" is atmospheric pressure. This kind of plasma source has been the subject of increasing research activity in recent years. A number of geometric variants have been explored, and operational requirements and typical plasma parameters have been determined. Large arrays of individual tiny sources can be used to form large-area, atmospheric-pressure plasma sources. The simplicity of the method and the capability of operation without the need for the usual vacuum system and its associated limitations, provide a highly attractive option for new approaches to many different kinds of plasma applications, including plasma surface modification technologies. Here we review the background work that has been carried out in this new research field.