• Journal of Energy Engineering
• /
• v.17 no.1
• /
• pp.15-22
• /
• 2008

This study was carried out to investigate physical and chemical characteristics of the distillates and residue of Athabasca oilsand bitumen obtained from Canada, using a vacuum distillation unit. The distillates and residue produced from the vacuum distillation were characterized through atomic analysis, SARA analysis, and measurement of boiling point distribution, molecular weight, and API gravity. The vacuum distillation equipment consisted of a 6-litter volume vessel, a glass-packed column, a condenser, a reflux device, a flask fer collecting distillates, and a temperature controller. The cutting of distillates was performed with four steps under the condition of full vacuum and maximum temperature of $320^{\circ}C$. The results showed that the sulfur amount and average molecular weight of the distillates were significantly reduced compared to those of oilsand bitumen. As the cutting temperature increased, the hydrogen amount decreased but the sulfur amount and average molecular weight increased in the distillates.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.4 no.1
• /
• pp.3-12
• /
• 1967

This study has been endeavored to deposit resistance films of tin oxide on the cylindrical Pyrex glass rods. In this report, at first an outline of the film formation is described and later some electrical properities of the resistance films manufactured through new method is discussed in detail. Because the new method which is called, "Chemical Vapour Reaction Process", is not only easy to get stable resistance films, but also doesn't need vacuum systtem, it seems to be a promising fundamental process to go into flow system mass production. Electrical properties of resistance films made by the new mathod are similar to or surpassing those by provious method (for example splay method). The top data thus obtained shows that surface resistivity is 25ohm/sq. with 12 ppm in temperature coefficient of resistor. resistor.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.3
• /
• pp.514-520
• /
• 1997

A single component of $Sb_2O_3$ glass has been obtained by a rapid quenching method in vacuum. The linear refractive indices were measured as a function of wavelength from 500 nm to 1060 nm. The refractive index at $n_{3{\omega}}$/(633 nm) was as high as 2.00. The optical band gap was estimated as 3.38 eV from the optical absorption spectrum. The third-order nonlinear optical intensity was determined by the third harmonic generation (THG) method. The $\chi^{(3)}$value was as high as $5.68{\times}10^{-13}$esu, about 20 times larger than that of $SiO_2$ glass.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.13 no.1
• /
• pp.43-49
• /
• 2005

There are several ways to mold the complex material, and it is divided to vacuum pack mold, compression mold, and hand lay up for a high molecular substance as a basic material. Moreover, it can be divided to general manufacturing (Single form) and mold manufacturing(Mold form) under normal temperature for Firefly. Firefly was manufactured with hand lay up and general manufacturing that using the foam core, glass fabric, and template without mold. However, mold manufacturing that is producing the surface by semi-sandwich using thin foam core and glass fabric then reinforce the inside with spar and rib is on developing. Mold manufacturing can make easy to production, standardize the quality, and possible to mass producing. In this paper, we present the mold producing process for canard aircraft "Firefly", and the problems and solutions during producing Firefly. Moreover, it complements the defect that the problems caused by master manufacturing error when produce several masters of a large part, and make the manufacturing process to be shortened by the replacement from the supplementary plate to the foam that is installed when producing lay up mold.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.693-698
• /
• 2002

For the evaluation of the plasma display panel (PDP)'s noise, vibration and sound characteristics of fanless PDP are measured and investigated. PDP is a type of two-electrode vacuum tube which operates on the same principle as a household fluorescent light. An inert gas such as argon or neon is injected between two glass plates on which transparent electrodes have been formed, and the glass is illuminated by generating discharge. For this discharge, both high voltage and currents are needed and cause an acoustic noise. We investigated the noise characteristics connected with both a electromagnetic elements from SMPS to panel through X, Y and logic board, and a mechanical elements form panel to case through transfer path which related with vibration and heat. To reduce the noise of PDP, a discharge pulse memory design related with both higher brightness and lower power consumption is important and mechanical characteristics connected with dissipation process of both heat and vibration generated by panel discharge must be investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.05a
• /
• pp.185-188
• /
• 2004

A diode structure of field emission lamps based upon carbon-nanotube is studied. The single-walled carbon nanotubes(SWNTs) were produced by arc discharge method. We made the 1-inch diode type flat lamp using CNTs. We applied anode voltage gradually to refine the field emission behavior of emitter in dynamic vacuum system to study the emission current. the brightness and efficiency, etc. The field emission properties was estimated by varying gaps between the cathode and anode, contents of the glass frit. The good luminous efficiency is showed in the gap $900{\mu}m$, $1200{\mu}m$ and contents of the proper glass frit. For the upper conditions, the luminous efficiencies were respectively 23.30, 11.12 1m/W.

• Journal of agriculture & life science
• /
• v.43 no.6
• /
• pp.105-109
• /
• 2009

Kyungsan nursery complex which has a vast area for the production of various species of fruit tree stocks is in a high demand of virus-free saplings. Apple tree stocks, the most important products, urgently need more rapid and reliable viral diagnosis. In this study, a bead beater was tested because of convenience in dealing with large number of samples. Also, industrial glass bead abrasive (0.4 mm in diameter) at very low cost was used in a disposable way. For bead beater-aided RNA extraction from apple stem tissues, the guanidine thiocyanate method was confirmed to be very reliable. Silca membrane filter tube in connection to vacuum filtering device was strongly suggested for simplifying RNA capture and washing steps. Apple virus detection was confirmed by RT-PCR.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.95-98
• /
• 2006

Filtration by fibrous filter is one of the Principle methods used for removing pollutant particles in the liquid. Because of the increasing need to protect both human health and valuable devices from exposure to fine particles, filtration has become more important. Filters have been developed with modified surface charge characteristics to capture and adsorb particles by electrokinetic interaction between the filter surface and particles contained in water. The main purposes of this study are to develop and evaluate the performance evaluation of the apparatus for making a positively charged porous filter media and to analyze the surface characteristics of the filter media for capturing negavitely charged contaminants mainly bacteria and virus from water. The experimental apparatus consists of a mixing tank, a vacuum pumping system, a injection nozzle, a roller press and a controller. The filter media is composed of glass fiber(50-750 nm), cellulose($10-20{\mu}m$) and colloidal charge modifier. The characteristics of filter media is analyzed by SEM(Scanning Electron Microscopy), AFM(Atomic Force Microscopy) and quantified by measuring the zeta potential values.

• Journal of the Korean Vacuum Society
• /
• v.18 no.3
• /
• pp.213-220
• /
• 2009

The optimal condition of low temperature deposition of transparent conductive Al-doped zinc oxide (AZO) films is studied by RF magnetron sputtering method. To achieve enhanced-electrical property and good crystallites quality, we tried to deposit on glass using a two-step growth process. This process was to deposit AZO buffer layer with optimal growth condition on glass in-situ state. The AZO film grown at rf 120 W on buffer layer prepared at RF $50{\sim}60\;W$ shows the electrical resistivity $3.9{\times}10^{-4}{\Omega}cm$, Carrier concentration $1.22{\times}10^{21}/cm^3$, and mobility $9.9\;cm^2/Vs$ in these results, The crystallinity of AZO film on buffer layer was similar to that of AZO film on glass with no buffer later but the electrical properties of the AZO film were 30% improved than that of the AZO film with no buffer layer. Therefore, the cause of enhanced electrical properties was explained to be dependent on degree of crystallization and on buffer layer's compressive stress by variation of $Ar^+$ ion impinging energy.

• Journal of the Korean Vacuum Society
• /
• v.17 no.1
• /
• pp.23-27
• /
• 2008

We have investigated the effect of annealing on the structural and optical properties of polycrystalline Ga doped ZnO (GZO) films grown on glass substrates by RF-magnetron sputter at room temperature. The structural and optical properties of as-grown GZO films were characterized and then samples were annealed at $400{\sim}600^{\circ}C$ in $N_2$ ambient for 30, 60 minutes, respectively. The field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD) were used to measure the grain size and the crystalline quality of the films. We found that the crystalline quality was improved and the grain size tends to be increased. The optical properties of GZO thin films were analyzed by UV-VIS-NIR spectrophotometers. It is found that optical properties of thin films are increased by annealing and can be used for transparent electrode application. We believe that the appropriate post-growth heat treatment could be contributed to the improvement of GZO-based devices.