• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.771-776
• /
• 1995

Tensile and J-R tests were carried out to estimate the effects of dynamic strain aging(DSA) on SA106Gr.C piping steel. Tensile tests were performed under temperature range RT to $400^{\circ}C$ md strain rates from $1.39{\times}10^{-4}\;to\;6.95{\times}10^{-2}/s$. Fracture toughness was tested in the temperature range RT to $350^{\circ}C$ and load-line displacement rates 0.4 and 4mm/min. The effects of DSA on the tensile properties were clearly observed for phenomena such serrated flow, variation of ultimate and yield stress, and negative stram rate sensitivity. However, the magnitude of serration and strength increase by DSA was relatively small. this may be due to high ratio of Mn to C. In addition, crack initiation resistance, Ji and crack growth resistance, dJ/da were reduced in the range of $200-300^{\circ}C$, where DSA appeared as serrated flow and UTS hardening. The temperature corresponding to minimum fracture resistance was shifted to higher temperature with increasing loading rate.

• Transactions of Materials Processing
• /
• v.18 no.5
• /
• pp.410-415
• /
• 2009

Experimental and numerical studies were performed to examine the effect of material temperature and reduction ratio on friction coefficient during hot flat rolling. We carried out a single pass pilot hot flat rolling test at the temperatures range of $900{\sim}1200^{\circ}C$ and measured the spread of deformed material while reduction ratio varied from 20% to 40%. Materials used in this study were a high carbon steel and two alloy steels. The dimension of specimen used in hot rolling experiment was $50mm{\times}50mm{\times}300mm$. We performed a series of finite element simulation of the hot rolling process to compute the friction coefficient change in terms of steel grade and reduction ratio. Results showed that temperature dependency of friction coefficient is not noteworthy but the effect of reduction ratio on friction coefficient is quite large. For high carbon steel, friction coefficient at reduction ratio of 30% is lower than that at that of 20%. Meanwhile friction coefficient at reduction ratio of 40% was one and half times large compared with that at that of 20%. The effect of steel grade on friction coefficient was significant when reduction ration was large, e.g., 40%.

• Structural Engineering and Mechanics
• /
• v.75 no.5
• /
• pp.621-631
• /
• 2020

A laboratory experiment is conducted is to investigate the behaviour of a low-mass-ratio and high aspect ratio flexible cylinder under vortex-induced vibration (VIV). A flexible cylinder with aspect ratio of 100 and mass ratio of 1.17 is towed horizontally to generate uniform flow profile. The range of Reynolds number is from 1380 to 13800. Vibration amplitude, in-line and cross-flow frequency response, amplitude trajectory, mean tension variation and hydrodynamic force coefficients are analyzed based on the measurement from strain gauges, load cell and CCD camera. Experimental results indicate that broad-banded lock-in region is found for the cylinder with a small Strouhal number. The frequency switches in the present study indicates the change of the VIV phenomenon. The hydrodynamic force responses provide more understanding on the VIV of a low mass ratio cylinder.

• Journal of the Korean Home Economics Association
• /
• v.30 no.3
• /
• pp.15-32
• /
• 1992

The purpose of this study was to detect the effect of the lower body type on the shape of flare skirts. The subjects for the wearing test were 50 female students, who were controlled in their hip and waist shapes. The skirts used for wearing test were six types(three flar angles $\times$ two fabric types). The effect of lower body type on the shape of flare skirts was determind by the hemline trace method and the silhouette photography. The data were then analyzed by the repeated measures of analysis of variance and the SNK multiple range test. The results obtained from this study were as follows : 1) When a flare skirt made with larger flare angle and better drapable fabric was worn, the numeric of the nodes increased as the drop value(hip - waist) increased. When a flare skirt made with smaller flare angle was worn, the width of horizontal sectio of hemline increased as the drop value increased. The hemline uneveness decreased on the sides and back as the drop value increased. When a flare skirt made with worse drapable fabric was worn, the sides angle of the flarskirt increased as the drop value increased. 2) When a flare skirt made with larger flare angle was worn, the numeric of nodes increased as the ratio of dropped hip increased. The wave-height increased and the back variation ratio of wave-height was higher than the front variation ratio of wave-height as the ratio of dropped hip increased. The hemiline uneveness decreased on the back as the ratio of dropped hip increased. When a flare skirt made with larger flare angle was worn, the sides angle of the flare skirt increased as the ratio of dropped hip increased.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.6
• /
• pp.348-352
• /
• 2014

In light of the sure protection function, the most important factors of a varistor are the clamping voltage ratio and degradation characteristics. The degradation characteristics of Pr/Co/Cr/Er co-doped zinc oxide varistors were investigated by impulse currents (0.4~2.1 kA) stress for the specified content of $Er_2O_3$ (0.5 and 2.0 mol%). The varistor doped with 2.0 mol% $Er_2O_3$ exhibited the best clamp characteristics, with the clamp voltage ratio (K) in the range of K = 1.63~1.88 at the impulse currents of 5-50 A. However, the varistor doped with 0.5 mol% exhibited excellent electrical stability, with variation rates for the breakdown field, for the nonlinear coefficient, and for the leakage current density of -6.9%, -12.6%, and -14.3%, respectively, after application of an impulse current of 2.1 kA. In contrast, the varistor doped with 2.0 mol% was destroyed after application of an impulse current of 1.2 kA.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.242-243
• /
• 2014

In this study, industrial by-products including blast furnace slag, incineration ash and waste gypsum were used with recycled fine aggregates to manufacture the zero-cement mortar. The replacement ratio of anhydrite gypsum was fixed as 0, 10%, 20% the replacement ratio fo WA1 was fixed as 0.5% and 1.0%, respectively. It could be identified that when the replacement of gypsum was 20% and WA1 of 1.0%, the strength could be in the range of normal strength.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2014.05a
• /
• pp.222-223
• /
• 2014

In this study, industrial by-products including blast furnace slag, incineration ash and waste gypsum were used with recycled fine aggregates to manufacture the zero-cement mortar.The replacement ratio of dihydrate gypsum and anhydrite gypsum was fixed as 0 and 10%, the replacement ratio fo WA1 was fixed as 0.5% and 1.0%, respectively. It could be identified that when the replacement of gypsum was 10% and WA1 of 1.0%, the strength could be in the range of normal strength.

• Journal of Mechanical Science and Technology
• /
• v.17 no.1
• /
• pp.122-128
• /
• 2003

This paper presents a thermodynamic analysis of heat pump system using water as a heat source and heat sink. The primary object in this study is the optimization of exergetic efficiency. Two different systems, 2-stream and 1-stream system, are analyzed in detail. Mass flow ratio (the ratio of mass flow rate of water through evaporator to that through condenser) is identified as the most important parameter to be optimized. It is shown that there exists an optimum mass flow ratio to maximize exergetic efficiency. The variation of optimum exergetic efficiency of 2-stream system is quite small and the value lies between 0.2∼0.23 for the range of investigation in this study. However, far better performance can be obtained from 1-stream system. This means considerable irreversibilities are generated through condenser of the 2-stream system. The effects of adiabatic efficiency of compressor-motor unit on the overall system performance are also examined in the analysis.

• International Journal of Safety
• /
• v.9 no.1
• /
• pp.12-20
• /
• 2010

In this study, a series of random field test and dynamic analysis in the time domain were carried out in order to find in the reason of fatigue damage of the main and the secondary members in the 3-span continuous steel plate girder railway bridge being under in service over 60 years. From the measured and the analyzed results, the stress distribution patterns were investigated for the members with fatigue damage. In addition, global and local numerical stress analysis was performed for the members damaged severely by corrosion, to estimate variation of the distribution by corrosion. Finally, a reasonable cut-off ratio in the steel plate railway bridge will be proposed by analyzing the equivalent stress ranges according the ratio.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.6
• /
• pp.274-284
• /
• 1995

The effect of turbulence and ignition energy on flame kernel growth in mathanol-air mixtures has been studied in a constant volume vessel. Experiments were made under different turbulent intensity conditions, ignition energy and over a range of equivalence ratio. Characteristics of turbulent flow were grasped by measurments of gas pressure and visualization of flame propagation. Flow velocity was measured by use of hot wire anemometer. A comparison of the effect of turbulence on ignition probability and flame kernel volume variation ratio is also presented.