• Journal of the Korea Computer Graphics Society
• /
• v.17 no.1
• /
• pp.1-7
• /
• 2011

We present a new technique for constructing a sweep surface using two-parameter motion. Firstly, a new rational B-spline motion with two parameters is introduced, which is obtained by extending its orientation curve and scaling curve to surface counterparts. A sweep surface is then defined by a single vertex v under the two-parameter motion and allows to represent different u-directional iso-curves depending on parameter ${\upsilon}$. Efficient techniques for modeling and editing the surface are achieved by intuitively controlling the two-parameter motion. We demonstrate the effectiveness of our technique with experimental results on modeling and editing a 3D propeller model.

• Geophysics and Geophysical Exploration
• /
• v.17 no.1
• /
• pp.1-10
• /
• 2014

To reveal and classify site characteristics in densely populated areas in Chuncheon, Korea, Rayleigh-waves were recorded at 50 sites including four sites in the forest area using four 1-Hz velocity sensors and 24 4.5-Hz vertical geophones during the period of January 2011 to May 2013. Dispersion curves of the Rayleigh waves obtained by the extended spatial autocorrelation method were inverted to derive shear-wave velocity ($v_s$) models comprising 40 horizontal layers of 1-m thickness. Depths to weathered rocks ($D_b$), shear wave velocities of these basement rocks ($v_s^b$), average velocities of the overburden layer ($\bar{v}_s^s$), and the average velocity to a depth of 30 m ($v_s30$), were then derived from those models. The estimated values of $D_b$, $v_s^b$, $\bar{v}_s^s$, and $v_s30$ for 46 sites at lower altitudes were in the ranges of 5 to 29 m, 404 to 561 m/s, 208 to 375 ms/s, and 226 to 583 m/s, respectively. According to the Korean building code for seismic design, the estimated $v_s30$ indicates that the lower altitude areas in Chuncheon are classified as $S_C$ (very dense soil and soft rock) or $S_D$ (stiff soil). To determine adequate proxies for $v_s30$, we compared the computed values with land cover, lithology, topographic slope, and surface elevation at each of the measurement sites. Due to a weak correlation (r = 0.41) between $v_s30$ and elevation, the best proxy of them, applications of this proxy to Chuncheon of a relatively small area seem to be limited.

• Journal of the Korean Ceramic Society
• /
• v.38 no.6
• /
• pp.558-567
• /
• 2001

본 연구에서는 알콕사이드를 전구물질로 하는 졸겔공정을 이용하여 Bi 과잉 12 mol%의 조성인 B $i_4$ $Ti_3$ $O_{12}$ 박막과 B $i_4$ $Ti_{3-x}$T $a_{x}$ $O_{12}$(x=0.1, 0.2, 0.3) 박막을 제조하였다. XPS 분석에 따르면 Ta 치환 x=0.2에서 Bi 4f의 photoemission 곡선이 낮은 결합에너지로 이동하였고 피크 강도가 감소하는 현상이 관측되었다. 이는 x=0.1과 0.2 사이에서 Bi-O 결합이 길어져 인장상태 하에 있었음을 나타내었다. B $i_4$ $Ti_3$ $O_{12}$(BIT) 박막의 유전상수와 유전손실은 100 kHz에서 340, 0.05이었고, B $i_4$ $Ti_{3-x}$T $a_{x}$ $O_{12}$ 박막에서 이들 값은 x=0.1에서 가장 높았으며, 각각 480, 0.13이었다. B $i_4$ $Ti_3$ $O_{12}$ 박막의 잔류분극과 항전계는 1.24$\mu$C/$ extrm{cm}^2$, 31.4 kV/cm 이었으나, Ta 치환 x=0.2에서 이들 값은 각각 19.7$\mu$C/$\textrm{cm}^2$, 49.5 kV/cm 에 이르렀다. 또한, B $i_4$ $Ti_3$ $O_{12}$ 박막의 누설전류 밀도는 ~$10^{-6}$ A/$\textrm{cm}^2$ 정도이었으며, Ta 치환은 누설전류를 감소시켜 Ta 치환 x=0.2 이상에서 BIT 박막에 비해 한 차수 정도 낮아졌다. Ta 치환에 따른 B $i_4$ $Ti_3$ $O_{12}$ 전기 물성에서 변화는 Bi-O 결합에서 관측된 인장상태로의 전이와 연관성이 있었으며, 덧붙여 치환에서 생성된 전자에 의한 정공보상이 이에 영향을 끼쳤다. 정공보상이 이에 영향을 끼쳤다.끼쳤다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.1
• /
• pp.154-159
• /
• 1987

In the previously reported Part I, the behavior of the flank wear for carbide tool was studied as a preceeding step to present a simple method for Quick Tool-Life Testing, and the following general equation was obtained $W_{f}$ =(a+bt) $V^{m}$ . In this study the following step-cutting formula for the constants a, b and m in the above general model is derived by using step-cutting data [a numerical formula] To check the validity of the above formula, the comparison is made between the tool-life equation inferred in this method and that inferred in the conventional tool-life testing method, when the wear criterion is 0.3mm. The equation obtained in the present method is V(T')$^{0.57}$=1763 whereas the equation obtained in the conventional tool-life testing method is V(T)$^{0.56}$=1605 The results of the above two formula are satisfactory and also verify the validity of the present research.earch.

• Journal of Energy Engineering
• /
• v.22 no.4
• /
• pp.333-337
• /
• 2013

본 논문에서는 태양전지의 Ribbon 두께(A-type:0.2mm, B-type:0.25mm)에 따라 3가지 온도조건 ($-40{\sim}65^{\circ}C$, $-40{\sim}85^{\circ}C$, $-40{\sim}105^{\circ}C$)으로 열충격 시험을 수행하였다. 그 결과, A, B type 별 초기 평균효율은 15.2%로 같았다. 하지만, 열충격 시험(600 Cycle) 후 Condition 1에서 A-type 7.5%, B-type 7.7%, Condition 2에서는 8.6%, 13.2%를 나타내었다. Condition 3에서는 각각 11.6%, 19.9%의 감소율을 나타내었다. 열충격 시험 후 A-type보다 Ribbon두께가 두꺼운 B-type의 효율이 크게 감소하였다. 이는 A, B type 모두 이종재료 접합부의 금속간화합물(IMC)층이 형성되어 전기적 저항이 증대된 것으로 판단된다. 또한, B-type의 I-V 특성 곡선 및 EL을 분석한 결과, p-n층이 파괴되고, 병렬저항이 감소하여, 장기적 신뢰성에서 A-type 보다 더 취약한 것으로 나타났다. 향후 태양전지 Ribbon 형상에 따른 장기 신뢰성 특성에 대해 수치해석 및 시뮬레이션 분석이 수반되어야 할 것이다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.379-379
• /
• 2022

기후변화로 인해 집중호우, 돌발 홍수 및 태풍의 규모가 대형화되고 있고, 이에 따른 수재해 피해 사례도 증가하는 추세이다. 특히 건설 현장 중 굴착공사 현장에서의 침수로 인한 사고는 인명피해로 이어질 가능성이 더 크기 때문에 더욱 주의가 필요하다. 하지만 현재 국내에서 실질적으로 굴착현장에 적용하기 위한 침수 대응 예측 시스템 및 구체적인 침수 예경보 체계, 기준, 매뉴얼은 존재하지 않는 실정이다. 따라서 본 연구에서는 굴착공사현장의 수재해 예방을 위한 침수 예·경보 시스템의 적용방안을 제시하였다. 또한 경제적이고 효과적인 측면을 고려하여, 공사현장 규모에 따라 적용하는 침수 예·경보 시스템을 이분화하여 소규모 공사현장에는 Track A, 대규모 공사현장에는 Track B 침수 예·경보 시스템을 적용하도록 제안하였다. 이러한 이유는 소규모 공사현장의 특성상 전체 공사비가 작고 운영되는 장비와 인력이 제한적이므로 침수 예·경보에 필요한 비용과 인력 투입이 어려울 수 있기 때문이며, 또한 대피가 필요한 전체 인원이 대규모 현장에 비해서는 적기 때문에 비교적 신속하고 원활한 대피가 가능할 것이라고 판단하였기 때문이다. 본 연구에서는 각 시스템별 적절하다고 판단되는 예·경보 기준을 제시하였다. Track A에서는 강우법에 의한 최소한의 경보시스템으로 필요한 안전목표를 달성할 수 있도록 고려하였고, Track B에서는 현장인원 대부분이 성인 남성임을 고려하여, 성인 남성의 부상을 유발할 수 있는 수심(H)과 유속(V)의 곱을 척도로 하는 한계 H·V곡선을 기준으로 운영되는 경보시스템을 제안하였다.

• Journal of radiological science and technology
• /
• v.28 no.1
• /
• pp.1-7
• /
• 2005

High-quality single crystals of pure $Li_2B_4O_7$ as well as $Li_2B_4O_7$ doped with Cu, Mn and Mg impurities (1.0mol%, respectively) have been grown from the melt of $Li_2CO_3+2B_2O_3$ by Czochralski method in platinum crucibles. To study the thermoluminescent properties, $Li_2B_4O_7$ series single crystal TLDs were made by cutting in the size of $4{\times}5{\times}1\;mm^3$. The glow curves show two or three peaks which can be easily deconvoluted. It is observed that room temperature($20{\sim}30^{\circ}C$) fadings of the dosimetric peaks of $Li_2B_4O_7$ series single crystal TLDs were about 10 % for 30 days. The relative photon energy response for $Li_2B_4O_7$ series single crystal TLDs were about 85 % when the responses were normalized to that measured with $^{60}Co\;(1.25\;MeV)\;{\gamma}-rays$. The measured data are in a good agreement with theoretical ones. The $Li_2B_4O_7$ series single crystal TLDs fabricated in this work can be used for monitoring personal and environmental radioactivity.

• Journal of Energy Engineering
• /
• v.23 no.4
• /
• pp.88-94
• /
• 2014

In this paper, Thermal Shock tests were performed varying the composition of the solder and ribbon thickness (A-type:0.2mm/60Sn40Pb, B-type:0.25mm/60Sn40Pb, C-type:0.2 /62Sn36Ag2Pb, D-type:0.25mm/62Sn36Ag2Pb) for evaluating the long-term reliability about Ribbon junction of Silicon solar cells. Thermal Shock test condition was performed during the 600cycles having $-40^{\circ}C{\sim}85^{\circ}C$ temperature range each 15 minutes; One cycle time was 30min. As a result, the initial efficiency of the A-type, B-type, and C, D-type were showed 15.0%, 15.4% and 15.8% respectively. After thermal shock test, the efficiency decreasing-rate of each type were as follow that A-type was 13.8%, B-Type was 15.4%. C-Type and D-Type was 15.3% and 16.2%, respectively. Also, degradation of surface changes and I-V characteristic curves were showed that the series resistance of the A, C-type was increased. Also, current lowering starting point of C-type shown 0.05volt[v] earlier than that of A-type. And B, D-type shown characteristics of composite lowering efficiency such as increase of series resistance, decrease of parallel resistance and cell damage. Therefore Initial solderability and efficiency of specimens using the solder with SnAgPb were superior. But, It has inferior the long-term reliability. The test was confirmed that as the ribbon thickness increases, long-term reliability of solar cell will decrease.

• Food Engineering Progress
• /
• v.15 no.1
• /
• pp.22-27
• /
• 2011

Changes in total nitrogen (T.N.) and total phosphate (T.P.) content in environmental waste water upon the reaction of biological purifying reagents were measured and the reaction rate was evaluated. The purification capacity of two biological purifying reagents composed of vegetable Lactobacillus fermentum (V.L.F.), Saccharomyces cerevisiae(S.C), and Bacillus subtilis(B.S.) were evaluated and compared with that of commercial water purification system operating by local government. After 18days of reaction, the mixture of V.L.F. and S.C. showed dramatic decrease of T.N.(36.21% of the initial value). The mixture of V.L.F., S.C., and B.S. showed faster reaction rate to decrease T.P. compared with that of the mixture of V.L.F. and S.C. The reaction constant of mixture of V.L.F. and S.C. was estimated to be 0.178 $day^{-1}$ by the curve fitting of the data of changes in T.N. during the reaction.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.117-124
• /
• 2019

Vibrio cholerae is a very important pathogenic bacterium that has to be monitored in seafood and ships' ballast water. Various methods have been developed to identify this bacterium, yet these methods are time-consuming and have limitations for their sensitivity to detect contamination. The purpose of the present study was to develop a robust and reliable method for identifying V. cholerae. Peptide nucleic acid (PNA) probes were developed to use for PNA-based asymmetrical real-time PCR techniques. The toxigenic Cholera enterotoxin subunit B (ctxB) gene was selected as a target for detecting V. cholerae and the gene was synthesized as a positive template for conventional and real-time PCR. Real-time PCR primers and PNA probes were designed and standard curves were produced for the quantitative analysis. The selected PNA probes reacted specifically to V. cholerae without any ambiguity, even among closely related species, and the detection limit was 0.1 cfu/100 mL. Taken together, the PNA probes and asymmetrical qPCR methods developed in this present study could contribute to the rapid, accurate monitoring of V. cholerae in marine environments, and as well as in seafood and ships' ballast waters.